Dodge Cars & Trucks - Recent Questions, Troubleshooting & Support


Here is a forum from dodge talking about the drive cycle https://dodgeforum.com/forum/2nd-gen-neon/199345-2004-neon-drive-cycle.html

Dodge Cars &... | Answered 23 minutes ago


How to set your clock stereo on 1992 Dodge Dakota

?Turn the vehicle on then push the SEL button. It should flash back and forth between the time and the radio station you are set to. Set it to the time position.
?Now push the SET button. On my original stereo a P comes up. ( I think the P means p.m. but I have not been able to figure out how to change that setting) Next try the SEL button. It should flash to the hour. Use the TUNE knob to scroll to the desired hour.
?Push the SEL button and you should be able to set the desired minutes the same way.
?Push the SEL button again and the clock on your vehicle stereo should be set.

1992 Dodge... | Answered 2 hours ago


you can get guide from many sites.. i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete

Dodge Cars &... | Answered 9 hours ago


If it has one it will be along the inner frame rail, usually on the drivers side.

Dodge Cars &... | Answered 13 hours ago


Sounds like an internal transmission problem- could be as simple as a shift solenoid but could be more, sorry but it's true :( Is there a check engine light on? Check it out with a good diagnostic scanner, one with transmission control module capability is ideal!

Dodge Stratus... | Answered 21 hours ago


SYMPTOM
P0508-IAC VALVE SENSE CIRCUIT LOW

WHEN MONITORED
Engine running. Battery voltage greater than 10 volts .

SET CONDITION
The IAC sense circuit is less than 175 mA . One Trip Fault.

POSSIBLE CAUSES
  • IAC motor operation
  • IAC motor
  • (K61) IAC motor control circuit shorted to ground
  • (K961) IAC return circuit open
  • (K961) IAC return circuit shorted to ground
  • (K61) IAC motor control circuit open
  • PCM
  • consistant_15.gifconsistant_16.gifconsistant_17.gif
      Thanks, don't forget to give me a great rating and comment please:)

    2005 Dodge Grand... | Answered 22 hours ago


    It's a shift solenoid, a simple fix done by removing the transmission pan and swapping out the bad solenoid for a new one. Diagnose Further with a Good Scanner to find out which shift solenoid is bad, then swap it out. Easy Fix, also inexpensive! See the pictures and the link I've attached below for further info & best of luck friend! https://dodgeforum.com/forum/2nd-gen-dakota-tech/285204-help-p0751.html
    ce6c61cb-9344-45d0-adea-6d2bb97724dd-1wxu0k0p10onw4f4p0hjypgu-3-2.jpeg

    1ac9d262-131e-4728-ad5b-6c6c21d362b4-1wxu0k0p10onw4f4p0hjypgu-3-5.jpeg

    Dodge Cars &... | Answered 22 hours ago


    This is the same procedure as a Dokota, you are in luck, there was nothing on the Durange but there isa good video for the Dakota. Replace Turn Signal for Dodge Dakota 2001

    2002 Dodge... | Answered Yesterday


    Usually you need to put the key in and turn a little(into the accessory poistion) then use a nail or small screwdriver to push up on the pin under the key cylinder. I had to replace the key on my 2002 Jeep and that was the steps.

    Dodge Dakota... | Answered Yesterday


    "P1206 = Calculated Injector voltage above threshold."
    This is an issue with the electrical signal to one or more of the fuel injectors. A Good mechanic or Auto electrician should be able to help sort it out.

    Dodge Cars &... | Answered Yesterday


    The cooling fan control relay is located behing the grill in a crossmember (see the pic). It works in conjuction with the Integrated Control Module.

    e0ef069.jpg1. Grill
    2. Fan control relay
    3. Rivet
    4. A/C condenser

    Hope this helps.

    2006 Dodge Grand... | Answered Yesterday


    try to leave the key in the ignition for at leas 15 min if nothing happen just take it to mechanic with good scan tools or to the dealer
    thank you

    Dodge Cars &... | Answered Yesterday


    starting noise could be:
    1- timing chain is not tide ( the tensioner not doing the right job)
    2-the starter sticking on with flywheel all the time
    3- engine have low oil
    whining noise after turn off could be :
    1-vacuum leak 2- Alternator pulley is bad

    Dodge Cars &... | Answered Yesterday

    Not finding what you are looking for?
    Dodge Logo

    117,344 questions posted

    Ask a Question

    Usually answered in minutes!

    Popular Products

    2000 Dodge Caravan
    2000 Dodge Caravan

    2,240 Questions

    1999 Dodge Durango
    1999 Dodge Durango

    -934 Questions

    1999 Dodge Ram
    1999 Dodge Ram

    1,750 Questions

    2000 Dodge Durango
    2000 Dodge Durango

    1,576 Questions

    2005 Dodge Caravan
    2005 Dodge Caravan

    1,470 Questions

    Top Dodge Experts

    Marvin
    Marvin

    Level 3 Expert

    84027 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22483 Answers

    Jonah Oneal

    Level 3 Expert

    14053 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...