GMC Envoy - Popular Questions, Answers, Tips & Manuals

This would be the shift linkage bushing, very common. When switching through the gears, the gear selector lights in the dash probably don't move from P.

2003 GMC Envoy | 18 views | 0 helpful votes

There may be four. Bank 1, sensors 1, 2 and 3 and bank 2 sensor 1. This link will help you find the sensor that you need.

2002 GMC Envoy | 24 views | 0 helpful votes

The service and repair manual with diagram will provide step by step help to locate and fix the problem on your own easily and you will get the manual from the given link Home Toolsnyou

2002 GMC Envoy | 31 views | 0 helpful votes

was it jerking before change out --check installation of unit

2006 GMC Envoy | 20 views | 0 helpful votes

Could be many things. But spark and fuel most common. 1st, is car getting adequate fuel? Check fuel pump or fuel filter. Then spark. Use spark plug tester for spark. Then mechanic.

2003 GMC Envoy | 18 views | 0 helpful votes

Google your question.
About 280,000 results (0.61 seconds)

GMC Envoy Cars &... | 48 views | 1 helpful votes

check connectors fuses and relays ----also check the connections ribbon connections and unit under rear seat drivers side --lift seat like your going to fold down

2002 GMC Envoy | 27 views | 0 helpful votes

yes pulley free wheels--- when clutch is engaged [turn on ]then compressor is turning as well

2004 GMC Envoy | 26 views | 0 helpful votes

The best way to fix the problem is getting help from service and repair manual with pictures and diagram which will give you step by step help to locate and fix the problem on your own and you will get the manual from the given link

2002 GMC Envoy | 39 views | 0 helpful votes

Your drive train may be in limp mode, which indicates something seriously wrong with it (engine or transmission). Check for trouble codes with a code reader.

GMC Envoy Cars &... | 19 views | 0 helpful votes

Your anti-theft system kicked in for some reason. If you shut it off, the engine will turn over but will not start. A Chevy or GMC dealership is usually required to reset the system, but you'll have to bring it to them. Dealer + Towing = BIG $$$$. A less expensive option would be a mobile mechanic (call them first) or a licenced locksmith. Either way you'll need to show ID and proof of ownership.

2002 GMC Envoy | 31 views | 0 helpful votes

Look for black wire. Check it by using an omh meter and testing it to a ground.

GMC Envoy Cars &... | 30 views | 0 helpful votes

Temperature blend door actuator is probably stuck on heat position , needs replacing more then likely. Videos on youtube showing how to replace it .

Now as far as it shutting down , that could be any number of thing's , could cost a lot of time an money tracking that down . It would be best if when it shut off it wouldn't restart ,easier to fix that way .

2004 GMC Envoy | 57 views | 0 helpful votes

Nothing you can do , have it towed to a qualified repair shop.

2002 GMC Envoy | 42 views | 0 helpful votes

located in the back . It's called the LGM fuse #2 (Lift Gate Module) The Lift Gate Module controls the defroster grid circuit.

GMC Envoy Cars &... | 42 views | 1 helpful votes

Not finding what you are looking for?

-3,824 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2004 GMC Envoy
2004 GMC Envoy

2,174 Questions

2002 GMC Envoy
2002 GMC Envoy

1,364 Questions

2003 GMC Envoy
2003 GMC Envoy

1,326 Questions

2006 GMC Envoy
2006 GMC Envoy

569 Questions

2005 GMC Envoy
2005 GMC Envoy

521 Questions

Top GMC Experts


Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides