1999 Peugeot 206 - Page 7 - Answered Questions & Fixed issues


drivers level 1 airbag igniter open circuit

If airbag light on dashboard is ON, in most cases there is a problem with ribbon cable located in "COM2000" module. When you remove airbag, look at the BLUE connector to see if wires are connected. Rather complicated repair for DIY. Best to find working used complete module.

Peugeot 206 Cars... | Answered on Sep 22, 2014 | 542 views


The light is on to tell you the vehicle has a fault, take it to a mechanic and have a scanner put on it and it will tell you the fault, good luck

Peugeot 206 Cars... | Answered on Oct 12, 2016 | 136 views


A meter will show a charge from an alternator but what charge was it . IF it is not 14.5 volts and DC volts not ac volts then the alternator is not working properly and that is why the light is staying on. Best have the electrics checked out at an accredited auto electrician shop.

Peugeot 206 Cars... | Answered on Aug 24, 2014 | 468 views


Check clean and tighten battery terminals . I once found a battery had been replaced over a wiring loom and the sharp side of the battery box had cut into it causing a inter mitten short.

Peugeot 206 Cars... | Answered on Aug 11, 2014 | 49 views


The windscreen wiper stick attached to the steering wheel column has two functions. The up and down movement is to control the operation of the front wipers and a small ring collar that rotates on the wiper stick handle to control the rear wipers.

Hope this helps. You can get a manual from this site and check on page 110 http://www.scribd.com/doc/43174930/peugeot-206-2005-2006-manual

Peugeot 206 Cars... | Answered on Aug 02, 2014 | 114 views


REPLACE THE FAN CLUTCH AND BLADES, BE FINE, ALSO CHANGE THE THERMOSTAT

Peugeot 206 Cars... | Answered on Jul 23, 2014 | 145 views


sounds like the immobiliser transponder is not being read, after five years you may have to get a dealer to reset it.

Peugeot 206 Cars... | Answered on Jul 19, 2014 | 150 views


its the cylinder at timing belt end IE drivers side in UK

Peugeot 206 Cars... | Answered on Jul 19, 2014 | 53 views


remove the console from the handbrake and you will see contact there.its possible you have to adjust the hight,adjust whit ignition is on.
so you can see it come on if not bin broken.

Peugeot 206 Cars... | Answered on Jun 20, 2014 | 78 views


lower ball joints are fitted from the bottom up and are either bolted back in place or are pressed in place . I have done this pressing bit by fitting the ball joint in place and doing everything up and then placing a jack under the ball joint and raising the car so that the weight is on the suspension and ball and then I use a heavy hammer and hit the arm down which generally drives the ball joint into place.. Remember that the weight of the vehicle makes the suspension arm press down on the ball joint so it and tries to pull it up through the arm

Peugeot 206 Cars... | Answered on Mar 15, 2014 | 83 views


Think you have a problem with the wiring connections but where ?? i couldnt tell you without a good look myself i would advise you ask a local mechanic to have a look for you

Peugeot 206 Cars... | Answered on Feb 27, 2014 | 101 views


Try pressing the lock and unlock buttons on the remote, holding for a few seconds, then trying the unlock and lock buttons to see if the alarm disarms...your description indicates the car alarm is still armed!

Peugeot 206 Cars... | Answered on Feb 18, 2014 | 211 views


Please seek your local mechanic.

Peugeot 206 Cars... | Answered on Jan 11, 2014 | 124 views


check the fuse if good then check heater resistor pack if falty replace

Peugeot 206 Cars... | Answered on Dec 31, 2013 | 81 views


hi gary ther is a resistor pack that feeds the motor take note of the colours of the wires and the size of the wires that feed the motor and follow them back to the resister block and replace the resister block hope this will be helpfull

Peugeot 206 Cars... | Answered on Dec 31, 2013 | 101 views


Hi, If the clock is on top of the centre dash, the panel holding it in just clips out with a gentle tug upwards. There is a couple of screws holding the clock in and then you will see the bulb holders in the rear of the clock. Any auto centre should stock the bulbs, They just turn half a turn to come out.Jon.

Peugeot 206 Cars... | Answered on Oct 04, 2015 | 192 views


Need new front wheel bearings on Peugeot 206 02 plate how do you change the bearings

Peugeot 206 Cars... | Answered on Oct 28, 2014 | 3,983 views


Check the transmission fluid, it may be low.

Peugeot 206 Cars... | Answered on Nov 26, 2013 | 202 views


by the battery in engine look at fuse cover for layout

Peugeot 206 Cars... | Answered on Nov 22, 2013 | 445 views

Not finding what you are looking for?
1999 Peugeot 206 Logo

113 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

scj103

Level 2 Expert

99 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...