2004 Peugeot 206 SW - Answered Questions & Fixed issues

Try turning steering wheel some each way while trying to turn key, pressure from steering may not be allowing it to unlock to let key turn. Other cars sometimes do that, if the locking wheel is gear you are talking about.

2004 Peugeot 206... | Answered on Jul 08, 2016 | 56 views

Check wheel nuts,check shocks or struts.

2004 Peugeot 206... | Answered on Mar 21, 2016 | 71 views

Here is some material you can read up on ..........
No Crank No Start

No one here can tell you the solution to your particular problem as there are many possible causes for the no start condition.

You will need to get the car to a Peugot service centre and have the car scanned for fault codes. Once this is done the cause or causes can be properly diagnosed and then any repair or parts replacements carried out.

2004 Peugeot 206... | Answered on Nov 22, 2015 | 129 views

change your com 2000 25248135-p2wuoloelwkh3ffddo0jqcip-2-0.jpg

2004 Peugeot 206... | Answered on Nov 27, 2014 | 44 views

you need to remove center dash assembly to unscrew the heater control assembly once you pull out the heater control assembly you should have access to the rear where the tiny bulb is and you will need the number marked on it or in your owners manual in specs lights some auto parts dont have the same size since there are many models and sizes you might have to buy from dealer and they have to order so look around to find one

2004 Peugeot 206... | Answered on Aug 06, 2014 | 343 views

run fault codes to find the sensors ,servos and solenoids that may be affected

2004 Peugeot 206... | Answered on Dec 28, 2013 | 87 views

there is a body control module that runs the instrument cluster2_12_2013_5_15_16_pm.png

2004 Peugeot 206... | Answered on Feb 12, 2013 | 377 views

Hola buenas a todo aquel que ve este problema que tengo ( tengo un problema con una hyundai Tucson modelo: 2009 cilindraje : 1.991 ) : me presenta tres c?digos de falla los cuales son ( p1327 - rel? de incandescencia abierto ) ( p0405)( p0562)(p1190) esos son los c?digos en los que eh estado trabajando * pero a?n no doy con el da?o del veh?culo , si me pueden ayudar se lo agradezco ? Ya que eh probado otra pcm revisado todo el ramal del motor asta los soquer de la pcm cambiado todo los censores. Y actuadores de precion de combustible. Y nada

Peugeot 206 Cars... | Answered on Aug 17, 2019 | 1,150 views

inside power distribution box under the hood!

Peugeot 206 Cars... | Answered on Mar 18, 2019 | 42 views

You can try out some guide from here reliable-store
they also provide live chat feature for instant help and it's very useful

Peugeot 206 Cars... | Answered on Mar 12, 2019 | 30 views

There's a website that has all this information about all this and manuals everything totally free there are many actually but I personally like few reliable-store .. let me know if u need help

Peugeot 206 Cars... | Answered on Feb 27, 2019 | 33 views

If you are positive that the bulb and connector are OK...then there could be several root causes:
Bad wiring:
There could be a short somewhere between the connector and fuse/relay or ground.
But you need to figure out first ... is it BOTH the high and low beams that are out on that side of the car?
I think your bulb has 3 spades for a combination high/low beam bulb. Knowing which line is dead helps on figuring out which wire(s) is the issue. If both high and low do not work ... then it is the ground wire.
If you have a voltmeter you can test out the wiring.
Bad Light Control Module (if your car has this; I could not confirm)
I am not sure if the Peugeot has a light control module but on some Saabs there is one and it caused your same symptom. Read link to learn more

Peugeot 206 Cars... | Answered on Jan 23, 2019 | 51 views

Not familiar with that particular model, but on most you must first remove the seat back and seat cover to access the airbag.

Peugeot 206 Cars... | Answered on Jun 07, 2018 | 41 views

Did you get the car plugged into a diagnostic reader after the battery change?
Some newer car ECU's need to be reset to 'new battery' settings. Over time the system alters the battery charge rate as the battery gets older and weaker so a new battery will overcharge if not reset..
The error code, (P0563), reads as "system voltage high".
Get the car plugged into a good diagnostic system and that will allow you to correct the error code and battery settings.
The other symptoms may settle down once the error code is sorted out.

Peugeot 206 Cars... | Answered on Apr 14, 2018 | 80 views

At this website www.reliable-store.com I found all complete guide, much better language, complete detail in
800+ pages, and they also have live assistance feature

Peugeot 206 Cars... | Answered on Mar 09, 2018 | 54 views

External Fuel Quantity Access
Fuel Pump Control Out Of Range
Fuel Pump Control Out Of Range
Fuel Pump Control out Of Range (Fuel Pump Driver Module/VLCM)
VSV 1/2/3 Circuit Range / Performance
Fuel Pump Control Out of Range
Fuel Pump Control Circuit
Fuel pump control out range
Fuel Pump Control Out of Range
Fuel Pump Control Out of Range
High Pressure Fuel Pump Circuit Malfunction or Fuel Pump Control Out Of Range

Peugeot 206 Cars... | Answered on Feb 09, 2018 | 59 views

If oil is not circulating around engine then there could be a blockage resulting in increase of oil pressure. But if your car is under warranty then why dont you take it back and mention your concern in case if something goes wrong.

Peugeot 206 Cars... | Answered on Jan 08, 2018 | 58 views

Not finding what you are looking for?
2004 Peugeot 206 SW Logo

33 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers


Level 3 Expert

85161 Answers


Level 2 Expert

89 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides