20 Most Recent 2003 Mitsubishi Lancer - Page 2 Questions & Answers


Is Fuse OK?How about a fuel filter.

2003 Mitsubishi... | Answered on Apr 03, 2017


Above radiator outlet hose from the engine side.

2003 Mitsubishi... | Answered on Mar 18, 2017


Inside the fuel tank like every other car since the 1980's

2003 Mitsubishi... | Answered on Mar 01, 2017


Don't worry about it. The clock has a very minimal draw on your battery and won't drain it unless you store it for years.

2003 Mitsubishi... | Answered on Feb 04, 2017


There is no fuel cut switch on the lancer. Need to know what you are trying to fix no fuel?

2003 Mitsubishi... | Answered on Sep 07, 2016


Scan Tools The Changing Field of Diagnostics Take it to a ASE certified repair shop .

2003 Mitsubishi... | Answered on May 13, 2016


have to remove airbag to fix this

2003 Mitsubishi... | Answered on Mar 30, 2016


Sounds like you have spark and no fuel.
Could be bad gas, sludge in the fuel line or injectors, or a failed fuel pump.
If you check fuel pressure with a gauge and it is normal, you may need to drain the tank and clean out the injectors.
Gasoline turns to shellac after several months, which acts like varnish.

2003 Mitsubishi... | Answered on Mar 06, 2016


Depending on how much room you have behind the headlight assembly, unplug the wire connector turn the bulb 1/3 - 1/4 turn counterclockwise and remove. when reinstalling DO NOT TOUCH THE GLASS (it is a halogen bulb) of the bulb when installing, doing so will transfer oils from your skin and cause premature failure. If you do clean the glass with rubbing alcohol and a clean cloth. If there is no room to reach in and remove the bulb, the headlight assy will probably have a couple of screws that when removed will allow you access to the bulb. BTW the part # you need is 9007

2003 Mitsubishi... | Answered on Feb 21, 2016


You will need to remove the center console to access the bulb that is burned out. you can follow this link and it kinda tells you how to take it out. the instructions are for a 2003 but there are no differences Removing Center Console evolutionm net

2003 Mitsubishi... | Answered on Feb 18, 2016


The globe or LED in the dash has failed. Usually the instrument cluster has to come out for this to be replaced.
.

2003 Mitsubishi... | Answered on Jan 07, 2016


Mitsubishi's have always had problems with their throttle bodys carboning up, Magnas and Pajeros especially. Clean the throttle body with a can of carburettor cleaner, don't forget to open the butterfly and get right in behind it. Also check your ignition leads with a multimeter, any more resistance than 4000 ohms per foot of lead length, replace the lead. The misfiring may also have now damaged your oxygen sensor, check this with an analog multimeter, the O2 sensor output should vary between 0 and 1 volt as the needle moves between these readings (to vary the mixture) if not then replace the O2 sensor also. This problem is not related to your tyres.

2003 Mitsubishi... | Answered on Nov 13, 2015


the marks on the cam shafts are directly vertical at the top in line with a mark in the back of the housing the balance shaft timing mark is at 9 oclock position
the crank shaft timing mark is at 10 oclock position ( lining up with a pointer) and the oil pump mark is also at the 10 oc;ock position lining up with a pointer
( to check the position of the oil pump sprocket remove a plug -shown in the book -and insert .30dia pointed screw driver (5/16 philips ) to at least 2.4 "
if it cannot be inserted to this depth move the oil pump sprocket until it can)
the process of assembly is -:
install the timing belt to the sprockets and pulleys in the following order , retaining the belt to the camshaft sprockets by the use of suitable binding clips ( clothes pegs etc)
crankshaft sprocket
oil pump sprocket
guide pulley
exhaust camshaft sprocket
intake camshaft sprocket
tension pulley
to help install the belt the auto tensioner on the lh side should be removed
all of this information will be included in a workshop manual covering lancer engines for the years listed and will also include all tensions for the bolts --If you do not have the workshop manual then it is STRONGLY recommended that you obtain one
information from autodata belt installation manual lancer 2.0 l
2003-2007 engines

2003 Mitsubishi... | Answered on Oct 17, 2015


The slave cylinder, which is present only on manual transmission automobiles, is located at the transmission bell housing, where it provides the hydraulic pressure-to-mechanical pressure conversion that actuates the clutch fork to disengage the clutch plate from the pressure plate.

2003 Mitsubishi... | Answered on Oct 04, 2015

Not finding what you are looking for?

945 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Lancer Mitsubishi

  • Lancer Mitsubishi

Most Popular Question

slave cylinder located motor

  • Cars & Trucks
Loading...