Top 10 2006 Ford Escape Questions & Answers

2006 Ford Escape Logo

Question

  • 8,915 People Helped

How to remove an engine

How to remove an engine from a 2006 ford escape and the book time required to do it?

Posted by on

Answer

  • Most Helpful of 4 Answers

Hi!!
Click on the following link for step by step.instructions on how to Remove and Install the Engine on a 2006 Ford Escape.
Good Luck!!!

Posted on Sep 13, 2010

Question

  • 6,229 People Helped

instructions for replacing front wheel bearing on

instructions for replacing front wheel bearing on 2006 ford escape

Posted by on

Answer

  • Most Helpful of 1 Answers

I have a 2002 Escape and have changed my bearings. The 2006 is the same. The front wheel bearings on the Escape are simple cartridge bearings, or Gen1 bearings, that are pressed onto the hub and knuckle. They are not so simple to replace. Unless you have the experience and tools, you'll need to take it to the dealer or a shop.

You will need a press and the correct press tools.
The knuckle/hub assembly needs to be removed from the vehicle.

Here's the short version:
Remove the tire/wheel.
Remove the brake caliper w/ bracket.
Remove rotor.
Remove the ABS sensor.
Remove axle nut and press the axle inwards, until loose. (sometimes easy, usual needs special tool).
Remove the strut bolts, tie rod, and the lower ball joint from the knuckle/hub assembly. Each of these connections can have it's issues.
Press the hub out of the assembly. One half of the inner race will be stuck on the hub. Use a bearing splitter to remove that half.
Remove the snap ring from the knuckle.
Press the rest of the bearing from the knuckle.
Press the new bearing into the knuckle. Press on the outer race only!
Snap ring.
Make sure the dust sheild is still in place.
Press the hub into the bearing. The bearing must be supported on the inner race only!
The point is that you must not press thru the balls in the bearing. That can cause the bearing to get brinnelled.... not good.
Reassemble the knuckle on the vehicle in reverse order. I like to put a little grease on the axle spline. The axle spline has a little helix on it... about half a degree. It's supposed to be a tight fit. The torque on the axle nut is 300Nm (about 220ft-lbs?). This torque is very, very important. It is needed to keep the bearing together and at the correct preload, so use a big torque wrench.

...or you can take it to the dealer.

Good luck.
Here are some pictures that may help illustrate the difficulty: cimg1162.jpg cimg1165.jpg cimg1256ss.jpg cimg1241.jpg

Posted on Jan 02, 2011

Question

  • 5,443 People Helped

HOW DO I REPLACE THE ALTERNATOR ON A 2006 FORD ESCAPE WITH A 3.0

ALTERNATOR REPLACEMENT

Posted by on

Answer

  • Most Helpful of 1 Answers

disassemble the right wheel assembly and pull out the right wheel axel. Remove the alternator throught the right wheel well.

Posted on Aug 06, 2009

Question

  • 5,258 People Helped

need to know what fuse goes to my rear windshield

need to know what fuse goes to my rear windshield wiper \

Posted by on

Answer

  • Most Helpful of 1 Answers

The fuse panel is located on the right-hand side of the center console, by the instrument panel. Remove the panel cover to access the fuses. Check position 21, 10AMP (*) Rear wiper motor, Rear wiper washer (colored in the diagram)...

zjlimited_683.jpg

(*) Mini-Fuse

Hope helps (remember to rate this answer)

Posted on Feb 11, 2011

Question

  • 4,826 People Helped

how do you get the

how do you get the alternator out of a 2006 ford escape

Posted by on

Answer

  • Most Helpful of 1 Answers

Well, this one is a royal pain, but you've likely already figured that out. A neighbor had to have the one in her Escape done and after looking at it (thinking how hard could it be to replace the alternator for her...) I directed her to a friend's shop to have it done. He still talks to me so I guess no long term harm done, LOL, but he did say he was never interested in doing another one on an Escape.

OK, well let's get to answering your question. I'll paste the general information for you here, plus the link at the end of it to where I retrieved it from rather than type the step by step from my own memory, but this is pretty much it, including the bulk of the tools you're going to need.

One further note, as difficult as these are to replace, make certain you're not skimping on quality by going to some general parts place with their "lifetime" replacement units. Bite the bullet, buy a factory unit from the Ford parts department and likely you won't be doing this job again any time soon.

Here we go:

DISCONNECT THE NEGATIVE BATTERY CABLE


1. Block the tires, set the emergency/parking brake, and put the truck up on jack stands and remove the front wheel.

2. Remove the black plastic splash shield from underneath the right side of the engine. It's held on by about 5 M8 bolts, and one Phillips head screw.

3. Remove the serpentine belt. With the cover off, from underneath you can put a 3/8" drive socket into the tensioner pulley.

3. Next you need to remove the right front axle. Do it in one piece. Loosen the 32mm nut that assembles the shaft to the spindle. Back the nut off so about half the threads can be seen- you will hit the head of the nut to get it to go back through the spindle. Remove the front (15mm) and rear (I used a 3/4" but it was slightly too large) bolts holding the lower control arm to the frame. I pulled the assembly away from the truck at this time and braced it. Use a socket on the nut. This will star the process. After it started to go through I used the jack handle until the axle went back through the spindle. Now remove the 2 nuts (10mm) holding the half-shaft bearing and slide the front axle out of the trans-axle case in one piece. PLACE A CATCH CAN UNDER THE AXLE, YOU WILL LOSE FLUID!!

4. (YOU DID DISCONNECT THE NEGATIVE BATTERY CABLE, right?) There are 2 plastic snap clips holding the back splash guard for the alternator. A flat head screwdriver will pry these out and and if you're careful you can reuse them. There are (3) M13's holding the alternator, two on bottom, one on top (do the top one first, it's easier to hold the alternator up to get the last bolt out. Remove these bolts and slide the alternator out of the way. (Try using different extensions and a u-joint on the ratchet, they can help in different combination's. This will also help when you are removing the alternator bracket.

5. Now, that the alternator is unbolted, you need to take off the alternator bracket. There are 3 (10mm) bolts that go from the rear into the engine block. The top can be seen from under the truck. The next one is below and the third is easily remove from the side of the car near the wheel.

6. Once the bracket is out, you can you have a little more room to get to the electrical connections. Be careful with the regulator connector, you need to push inn the tab that holds it in. I used a flat screw drive on the tab to release the lock. If you look at the new alternator and you will see a square hole in the connector where the lock engages the connector). The positive wire is held on by a 10mm nut.

Put is all back together. You will lose a little over a quart of tranny fluid so you may want to pick that up when you get the alternator.

The hardest part for me was literally unplugging the alternator. There is no extra wire so getting in there to push the tab and pull the plug was rough.

Total time from start to finish was 2hours 15minutes from the time I broke the first lug-nut loose until I started the truck, this included a run to the auto store to empty my oil container so I could catch the transmission fluid and a 10 minute break for some water. It was about 90 degrees and very humid. I used all hand tools, no air. I'd be happy to go another 6 years and 180,000 miles before I had to replace this thing again, especially in the summer when my other truck is broken down and taking up the space in my air conditioned shop.


OK, me again. Here's the link I borrowed the information from for you and good luck on this one, it's a royal pain, even with a lift.

http://www.ford-trucks.com/forums/465864-changing-alternator.html

Posted on Mar 24, 2011

Question

  • 4,822 People Helped

How to troubleshoot P0340 Camshaft Position Sensor Circuit Malfunction code after replacing the sensor?

I got the OBDII code p0450 on my 2005 Ford Escape, 3.0 4wd 6 cyl. I replaced the Camshaft Postition Sensor, and the error comes back within a few miles. How does a total automotive idiot, who has limited funds, troubleshoot P0340 Camshaft Position Sensor Circuit Malfunction after replaceing the sensor? Please help?

Posted by on

Answer

  • Most Helpful of 1 Answers

Where is the camshafts on BMW z3 1997

Posted on Oct 04, 2013

Question

  • 4,435 People Helped

flashing 4wd and steady abs light on ford escape

flashing 4wd and steady abs light on ford escape

Posted by on

Answer

  • Most Helpful of 1 Answers

I have a 2005 Ford Escape and have this problem. I can tell you that if the light comes on every .8 miles and blinks for 8 times, learn to live with it. After taking to dealer when it first started in about 2008, having the tone ring changed on the CV's for the tires, after been told maybe an alien lived in there....the light sell happily blinks on.If it comes on and stays on I would worry more than if it blinks intermittently. Mine has what they call "Intelligent 4-Wheel Drive" [which must be an oxymoron], but still has the 4X4 light to indicate when supposedly it switches in to 4-wheel drive according to driving conditions. Certainly if you haven't noticed any other abnormalities with how the vehicle drives this could very well be the culprit.Hope this helps.

Posted on May 22, 2012

Question

  • 4,104 People Helped

how to change a tone

how to change a tone ring on a 2006 ford escape

Posted by on

Answer

  • Most Helpful of 3 Answers

here is how I do it.
http://youtu.be/3xZBld7MW8E

Posted on Aug 24, 2013

Question

  • 4,034 People Helped

Transmission Problem - Ford Escape 2006

I just got back from AAMCO and they told me that a computer scan revealed the following codes: P0732 - Gear 2 Incorrect Ratio and P0734 - Gear 4 Incorrect Ratio. How can I fix this? I have a 2006 Ford Escape but was told that my transmission is that of a Mazda. Please help. I need my car. Thank you.

Posted by on

Answer

  • Most Helpful of 1 Answers

P0732 and P0734 indicates gear ratio errors in 2nd and 4th gears, basically no 2nd and 4th gear. The one thing 2nd and 4th gear has in common is the band, the band is known to break, this is a common failure with this transmission and happens on a regular basis.

You need to remove the transmission to repair it.

Posted on Mar 08, 2015

Question

  • 3,676 People Helped

2006 ford escape 37,000 miles. My abs light stays

2006 ford escape 37,000 miles. My abs light stays on and the 4wd light flashes. I,m taking a trip next week. Is this something I can put off until I get back?

Posted by on

Answer

  • Most Helpful of 4 Answers

You likely have a cracked ABS tone ring. I had no idea what that meant when I was researching my girlfriends vehicle (2006 Escape hybrid) but sure enough that it what it was. She was getting the Service 4X4, Service Braking System, and the ABS light was on in the car. The tone ring is a gear that fits on the end of your CV shaft and can be found right behind your tire (if you search this problem on google you should find some pictures). You can see this without removing anything from the vehicle. There is a sensor that counts the gears of this ring as it goes by to determine your speed and whatnot. This information is used by the braking system and if the ring is cracked it will spin freely and the computer will not know what is going on and throw an error (or two or three). You can fix this two ways: replace CV shaft (about a $70 part) or replace the ring itself (a $12 - $15 part). Labor is what is going to get you on this. You can disconnect fuse #34 (5 amp fuse) to disable the ABS, but on my girlfriend's car this also disabled the power steering.

Posted on Jun 14, 2010

830 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2002 Ford Escape
2002 Ford Escape

1,094 Questions

2001 Ford Escape
2001 Ford Escape

1,056 Questions

2005 Ford Escape
2005 Ford Escape

1,058 Questions

2003 Ford Escape
2003 Ford Escape

869 Questions

2004 Ford Escape
2004 Ford Escape

538 Questions

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

2006 Ford Escape Escape

  • 2006 Ford Escape Escape

Most Popular Question

rear glass hatch open fix

  • Cars & Trucks
Loading...