20 Most Recent 1988 Pontiac Firebird Questions & Answers


What are the symptoms? Dirty fuel, clogged injectors, worn starter etc can all be a part of this...clean throttle body too.

1988 Pontiac... | Answered on Sep 25, 2015


Could try the crank sensor, that is where I would start. Next would be the timing & compression.

1988 Pontiac... | Answered on Dec 06, 2014


sounds like it needs a new clutch theres no way around it your letting out the clutch fully before it moves at high revs your clutch is burnt out it only works better when its hots because its expanded by the heat but when its cooled down it wont move again yep its a new one.

1988 Pontiac... | Answered on May 05, 2014


Before you spend a ton of money, have the timing checked

1988 Pontiac... | Answered on Apr 03, 2014


Sometimes when you check a battery if you have wiggled it then it starts it could be as simple as a loose connection or dirty posts. On a very small amount of the time the wiggle could just liven the battery up long enough to get another start out of it (this will not work over and over again). From what you write this could be in need of a battery or alternator or just cleaning the battery posts. Without more info I can not say. Does it click and do nothing? Does it make a grrr noise that kinda tapers off to nothing (like it wants to start but just can't get there)? Do the headlights work and are they bright or do they seem weak? Post any info describing any noise it makes or doesn't make (if none) and I will help you more.

1988 Pontiac... | Answered on Mar 26, 2014


It would appear that steps need to be taken to determine the current draw . it can not unless there is a circuit for it to do so . Disconnect the earth strap from the battery and insert an amp meter in the circuit . IF there is a circuit for the current you will read that current and that will point to what unit is capable of using that current with out serious effect. Low current (up to 3amps ) indicates lights so check boot light still on-glove box light on- interior light on-head light module faulty etc.; Higher draw then look for ECM working when it should be off--sensors operating from shorts __HO2s sensor ABS unit operating. Starter motors I would discount because if the solenoid was operating the starter would be spinning the motor. Check that the audio systems are not operational with out making noise .Units I would be checking would be automatic units that draw through a relay and a check for this would be to watch the amp meter for a change as each power wire to the relay/s was removed and re installed . IF you find a relay that causes a variance I would replace that module and recheck the current draw.

1988 Pontiac... | Answered on Mar 22, 2014


Take it in for a fuel injector cleaning, Happened to me with a used Mustang I bought would die when I shifted gears then back on when I let the clutch out. Too to 3 shops and they had no idea, went to the dealer and instantly knew what it was, about $80 to fix it. Has to be done in a shop because they use a special machine to clean out the fuel lines and injectors. I'm hoping it's as easy as mine was to have fixed.

1988 Pontiac... | Answered on Jan 23, 2014


at a low pressure as you are relying on a float system to control the fuel level. So about 10 psi would be ample.

1988 Pontiac... | Answered on Jan 05, 2014


Plz check adjustment on transmission

1988 Pontiac... | Answered on Nov 14, 2013


Is this a manual or automatic trans.?

1988 Pontiac... | Answered on Nov 14, 2013


Retime it. Put #1 cylinder at TDC of compression stroke. Pull number one spark plug: with finger over hole turn the crank with a socket and feel for the pressure buildup as engine turns. When you feel pressure, that means number one piston is rising on it's compression stroke. Now turn the crank on around until it is lining up the zero mark on the pointer scale. TDC of compression stroke.
Now put the distributor in so that the rotor when installed is pointing to the number one spark plug tower. Distributor shaft will turn slightly as it is installed, so start with shaft and rotor turned a bit back, so when slides into position, rotor is pointing directly to #1 plug tower. Keep playing with it until you get it right.
Good luck.

1988 Pontiac... | Answered on Aug 28, 2013


I would check the fuel pressure regulator, fuel filter, there might be a centrifugal cut-off switch. No output from the crankshaft position sensor would probly cause that. When you turn the key on you should be able to hear the pump run for a couple seconds. If not, could be a short circuit, loose connection, that sorta thing.

1988 Pontiac... | Answered on May 27, 2013


it could be the fuse.you dont want to look at the alternator just yet so start at the fuse box and work your way to under the hood down by the head lights theres k

1988 Pontiac... | Answered on Apr 30, 2013


It sounds like you may have burned out your fusable link. It's a special wire that comes off the starter solennoid and is designed to burn off in the event of an overload. DO NOT REPLACE IT WITH REGULAR WIRE, THIS IS A LEADING CAUSE OF CAR FIRES.
You will want to check for what caused the overload condition that caused the fusable link to burn out in the first place.

1988 Pontiac... | Answered on Apr 30, 2013


You follow the top radiator hose to the thermostat
housing & remove 2 bolts

The heater core-- I would try flushing out from the
heater hoses,just don't use full garden hose pressure

1988 Pontiac... | Answered on Mar 06, 2013

Not finding what you are looking for?
Cars & Trucks Logo

136 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Firebird Pontiac

  • Firebird Pontiac

Most Popular Question

battery drain in 3 3l motor

  • Cars & Trucks
Loading...