20 Most Recent 1996 Dodge Ram 1500 Club Cab Questions & Answers


Here's a link to a pdf file containing the headlight wiring diagram for your year model Dodge Ram 1500..
I can't help but notice that you say you've replaced the headlight relay? That's quite odd, because there is NO headlight relay on this vehicle- only a 40 amp fuse located in the power distribution box that sits behind the battery inside the engine bay.
The switch is notorious for burning out because there is NO RELAY on this vehicle, and there is a recall (#819) but this only affects 3500 models even though the headlight wiring is the same for 1500,2500 and 3500 model Rams.
Here are two more links that will help you troubleshoot your headlights problems.
HereInformation on Putting a Relay in the Wiring System

1996 Dodge Ram... | Answered on Mar 21, 2019


Sounds like it's worn out, best take into the shop for repair, should only cost $20 with parts.

1996 Dodge Ram... | Answered on Sep 03, 2018


check the fuel filter and pump. if the ignition spark is ok.

1996 Dodge Ram... | Answered on Jan 03, 2018


starter solenoid is bad perhaps .

1996 Dodge Ram... | Answered on Dec 03, 2017


it most likely needs new plugs and an o2 sensor. it also has a large evap leak. thats what all those codes mean. you could have looked them up yourself on google. po352 and po 356 are telling you two cylinders are not firing number 2 and 6 so change the plugs first and go from there. or get pro help so you dont just throw unneeded parts at it like many people do.

1996 Dodge Ram... | Answered on Nov 16, 2017


Sounds like it's running rich when it should be pulling off the "choke" as it's warm-ish. Maybe a temperature sensor somewhere.

1996 Dodge Ram... | Answered on Apr 08, 2017


Sounds like u have an air bubble. Easiest way to get that out is jack the frt of the truck up as high as u can get it with the radiator cap off and run it

1996 Dodge Ram... | Answered on Jan 03, 2017


REMOVAL & INSTALLATION
  1. Clamp the seat belts to keep them from retracting.
  2. Locate and disconnect seat wiring at the connector(s).
  3. Move front seats forward or back for access to the hold down hardware.
  4. Put the rear seats in the stowed position.
  5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
  6. Remove the hardware securing the seat.
  7. On split bench models, lift the center seat upward to clear attachment stud
  8. Remove the seat from the vehicle.
NOTE Do NOT activate the track adjusters once the fastening hardware is removed.
  1. Installation is the reverse of removal.

336abe0.gif


Fig. Disconnect the wiring from under the seat

36c62e2.gif


Fig. Seat track mounting hardware locations-typical


d95c538.gif

Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram


1589e1e.gif

Fig. Split bench seat assembly-Ram


616f086.gif

Fig. Bucket seat mounting components-Durango shown


851105e.gif

Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

1996 Dodge Ram... | Answered on Oct 21, 2016


Possibly the replacement headlight switch has the same defect.

1996 Dodge Ram... | Answered on Feb 18, 2016


This is likely a short in the power distribution block located on your stearing column. There was a recall for this problem. Contact the dealer for information.

1996 Dodge Ram... | Answered on Dec 14, 2015


Sounds like an aftermarket security system.

1996 Dodge Ram... | Answered on Nov 22, 2015


There are 3 different engines for that year but the 5.2 and 5.9 are the same but gave you a picture of both anyway. I hope this helps and good luck.


clifford224_243.jpg


clifford224_244.jpg

clifford224_245.jpg

1996 Dodge Ram... | Answered on Nov 01, 2015


idle air controll motor is bad

1996 Dodge Ram... | Answered on Oct 22, 2015


I have blown tail lights in my 96 Dodge Ram 1500
Can anyone help me

1996 Dodge Ram... | Answered on Oct 08, 2015


How is your transmission fluid level?

If you put it in neutral can you push the truck by hand or are the brakes binding?

1996 Dodge Ram... | Answered on Sep 18, 2015


check the crankshaft position sensor it may be sending a varying signal to computer

1996 Dodge Ram... | Answered on Jun 14, 2015


should have some cotter pins on frame you can pull to put everything in place and on column in engine bay

1996 Dodge Ram... | Answered on Apr 20, 2015

Not finding what you are looking for?
Cars & Trucks Logo

703 questions posted

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ram 1500 Dodge

  • Ram 1500 Dodge

Most Popular Question

just bought 1996 dodge ram 1500 studers

  • Cars & Trucks
Loading...