20 Most Recent 2005 Ford Explorer Sport Trac - Page 7 Questions & Answers


need more information please

2005 Ford... | Answered on May 08, 2011


Thanks for choosing FixYa and welcome.

2005 Ford... | Answered on Apr 30, 2011


When You say highlights, do you mean the highbeams?

2005 Ford... | Answered on Apr 18, 2011


If you lost the code it is also located on the door lock module. should be located in the kick panel.

2005 Ford... | Answered on Apr 14, 2011


  1. Lift the console lid.
  2. Take the two screws out from the front console cover. It is the cover that goes down around the shifter.
  3. Remove the cover by pulling up from the back.
  4. Next pull the front cover off from around the radio. This cover goes all the way down to the center console.
  5. Unlug all connections.
  6. Take the 4 screws out from around the radio that hold it in.
To install just repeat the steps in reverse.

http://www.ford-trucks.com/forums/867595-2009-sport-trac-radio-removal.html

2005 Ford... | Answered on Mar 14, 2011


Check fluid levels. If its not low, it may be time for a rebuild. Try in all gears to see if it will move

2005 Ford... | Answered on Mar 06, 2011


  1. 1 Drain the coolant from your Explorer into an adequate container by opening the drain plug at the bottom of the radiator. Save the coolant for reuse if it is relatively new and clean.
  2. 2 Remove the negative battery cable from the battery if your Explorer has a 2.9-, 3.0-, 4.0- or 5.0-liter engine. This step is not necessary for 2.3- and 2.5-liter engines.
  3. 3 Follow the upper radiator hose to the front driver's side of the intake manifold, where it meets the engine. This is where the thermostat housing on your Ford Explorer is located. If necessary, remove the air cleaner duct for easy access to the housing.
  4. 4 Loosen the clip on the end of the radiator hose and pull the hose off the thermostat housing. Use a 10mm wrench or socket to remove the two retaining bolts on the thermostat housing cover. Remove the cover.
  5. 5 Note the position of the thermostat before removal. Pull out the old thermostat. Seat the new thermostat inside the housing in the same position as the old one, spring-side facing into the engine. Install new gasket over the thermostat.
  6. 6 Reattach the thermostat housing cover and the radiator hose. Reinstall the air cleaner duct if removed earlier. Fill the radiator with reserve or new coolant. Start your Explorer and run with the heater blowing until the engine gets warm. Check for leaks.

Read more: How to Change the Thermostat in a Ford Explorer ' eHow.com http://www.ehow.com/how_4484916_change-thermostat-ford-explorer.html#ixzz1CLSvmPwR

2005 Ford... | Answered on Jan 28, 2011


With test light, verify you have power & ground to the motor, when ignition is on & switch is on high.If so, blower motor will need to be replaced. If not check fuse or blower motor resistor.

2005 Ford... | Answered on Jan 17, 2011


yes you can but you need special tools you need an air compressor and hose with a fitting that will screw into your sprrk plug hole. then you need an over head valve spring compressor. the air from the compressor will hold the valve against the head while you remove the valve retainers or collets to remove the spring. then you just assemble it all again is not hard but you do need the right gear

2005 Ford... | Answered on Jan 11, 2011


J C Whitney located in Chicago ... one of the biggest after market outfits in the country ...

2005 Ford... | Answered on Dec 28, 2010


I'm surprised they didnt sel you a oxygen sensor. Let the engine idle and see if you can locate a vacuum leak. listen for a air hissing noise. the pcv lines have rubber ends and are suspect. the dealer will have the parts you need.

2005 Ford... | Answered on Dec 11, 2010


They do make it easy for you there is a web sit go to www.fleet.ford.com under the Maintenance tab at the top by your toolbar on your monitor. They have a VIN Decoder program you will need to inter you VIN number it takes all of one minute to spit out you breakdown print page last item on list is your code under Prod Sequence Number and there you have your code!

2005 Ford... | Answered on Dec 10, 2010


Should be inside the fuse box or pluged into the back of it its larger then anything else in there and round and unplugs you just plug the new one in

2005 Ford... | Answered on Dec 04, 2010


Why would you waste money on fuel injection cleaning?
Why would you replace perfectly good ignition wires,they
do not wear out. (You only replace when they fail)
I have had OEM wires on a veh for over 17 years,over 18 on another
and 21 years ,on the one I currently use.

You paid to have preventative maintainance work done to
your vehicle.
Now it is either the same as before or worse.
Take it back,and tell the shop why you went there in the first
place. If you don't spend time there and be part of the solution,
they recommend and start performing services they make money on.
That is not how you do drivability diagnostics.

2005 Ford... | Answered on Nov 25, 2010

Not finding what you are looking for?
Cars & Trucks Logo

403 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Explorer Sport Trac Ford

  • Explorer Sport Trac Ford

Most Popular Question

fuse box diagram 2005 ford explorer

  • Cars & Trucks
Loading...