20 Most Recent 1994 Geo Metro Questions & Answers


Sounds like a major internal problem.

1994 Geo Metro | Answered on Apr 25, 2019


Unfortunately, both of these items are equally important and repairs can't normally be avoided by taking care of your car.

Your MAP (Mass Air Pressure) Sensor measures intake manifold vacuum pressure to help control the air and fuel mixture and timing. It contains a pressure-sensitive element that connects to an electronic circuit, generating a signal that changes with pressure changes in the manifold.

Your EGR (Exhaust Gas Recirculation) valve recirculates exhaust gases through the intake manifold to be burned again, cooling peak combustion temperature. Dilutes the air and fuel mixture to keep the nitrogen oxide emissions within breathable limits. And yes, it could very well be that the EGR solenoid that is causing the issue.

Both units effect your vehicle's fuel/air mixture. This is important because your vehicle running lean/rich can cause "snowball" problems. For example, a faulty EGR can cause the vehicle to run rich/lean. If not repaired, in time, the exhaust caused by the wrong rich/lean fuel mixture can damage the O2 sensors and/or catalytic converter.

If I had to pick, I'd start with your MAP Sensor. One guess I would have is that your MAP Sensor failed and made your vehicle start burning the wrong fuel/air mixture. Assuming I'm right, this could have damaged the EGR Valve. So, I see no reason to replace the EGR Valve alone, just so it too can be damaged by the poor fuel/air mixture caused by the still-faulty MAP Sensor. If your lucky, you may see the faulty EGR code disappear once your MAP Sensor is replaced.

Hope this helps and good luck!

1994 Geo Metro | Answered on Mar 28, 2019


There is a transmission controller that is located under the dash beside the right hand side of the steering column. It is held on to a bracket by two 10mm bolts. A change in that transmission control computer will make the transmission shift like new

1994 Geo Metro | Answered on Oct 26, 2018


I have read your problem and you can easily get the solution of your problem at the given link toolsnyou.com they provide the service manuals.Do visit it once. http://toolsnyou.com/

1994 Geo Metro | Answered on Jul 31, 2017


I think you have a mechanical issue with the transmission and it will need to be rebuilt.

1994 Geo Metro | Answered on Jun 30, 2017


Yes, correct. There is only the cam sensor in the distributor for the ecm's cam/crank reference signal. Many factors are figured in for pulse width, getting the air/fuel mixture correct.
Have you checked the ground for the ecm? The CEL does work? Too odd that both computers had no injector ground control, you must have missed something. Use an ohmmeter when you checked for continuity on the injector ground wire?

1994 Geo Metro | Answered on Jun 11, 2017


1)Throttle body butterfly stuck or gummed up.
2) Idle control valve gummed up or electrically inop..
Spray cleaners will solve the problem unless it's electrical .

1994 Geo Metro | Answered on Feb 02, 2017


Check your coolant level, you may have a head gasket leak sending coolant through the cylinders causing the "smoke".

1994 Geo Metro | Answered on May 21, 2016


If the shift lever is what is hard & sticky, get some grease & lube the handle at the joint at the trans. ( Maint. anyway) . The right gear oil? Was it doing it before the oil chg ? How's the clutch feel? Clutch, Pressure plate & throw out bearing poss. Smell any burning smells? One step at a time. Good luck

1994 Geo Metro | Answered on Nov 19, 2015


You want a simple answer but there is not one. The ECU looks at many things to determine what (if any) pulse is proper. Any sensor which sends no information or info outside of normal limits can prevent pulse. No info from crank/cam sensor is common issue, Bad EFI fuse or relay can do this. Bad ECU ground or other ground (Fuel rail) can do this. Many sensors can be tested with ohm meter.

1994 Geo Metro | Answered on Apr 20, 2015


no man on earth can answer, because we can't look either.
only looking at real damage works.
damage or wear really have no limits in the physical world.
we examine it carefully to see what is wrong, and then replace parts that are beyond repair.

1994 Geo Metro | Answered on Apr 14, 2015


no photos, and we are to guess failures in the physical world?

1994 Geo Metro | Answered on Mar 31, 2015


The PCM (ECU does that) its part of what is called EFI, electronic fuel injection, it's a computer, that gets inputs, and uses those inputs to injector perfectly at ALL times.
what engine? 3cy. or 4? is it TBI injected or MPI injected
1 injector or 4? we need to know that first.
does it run on test fuel for 3 seconds.
when was last time it run perfect, last week last year. what?
first off stop guessing, you can go broke that way.
want to diagnosis it? the steps are easy. if fuel is good..
  1. fuses good.?
  2. CEL lamp glow keyon, if not ECU is bad. or bulb , it must glow.
  3. compression over 150PSI on all cyl. (w.o.t = wide open throttle)
  4. do a 60k, mile tune up yet, filters, spark,. and cam timing belt.?
  5. if not, why wait?
  6. 6: is spark good tall cylinders not just 1? is the timing way off if yes, the cam belt did slip, do not fiddle tiiming, fix the belt. first.
  7. ok it now magically runs on test fuel for 3 seconds and sounds great. so we do fueling last.
  8. fuel pressure tests are next. takes $20 gauge got one?
  9. ill stop here, as fueling tests are long play.l..... ask. if you can get to step 9,

I think all 94 metors are TBI engines, one injector
up to 1997 inclusive.
then the 1998 offered 4cyl, MPI injected engine.


have you learned how to use flash codes (DTC) yet?
insert jumper , key on, see CEL lamp glow and flash 12s'
the crank for 5seconds, see if the flashes go to 41 or 42?
bingo if yes.
the TBI allows the mech to watch injection, at the TB.
with top hose off. you can watch it inject as person 2 cranks.
does it?
the ECU brain cuts fuel at the first sign of:
  1. lost spark (to stop fires)
  2. lost Cmp sensor, same .
  3. TPS ground wire busted and ecu things foot is W.O.T (super secret unflood mode) (or TPS cracked in half inside)
or total loss of fuel pressure.

1994 Geo Metro | Answered on Mar 27, 2015


click metro here
and read
http://www.fixkick.com/
see those 2 forums.
or here
http://www.teamswift.net/index.php
GEO swift?

if you own any GEO, ANY.
be proactive (its old) and buy the books, then ask questions.
http://www.ebay.com/sch/i.html?_odkw=1993+geo+metro+operators+guide&_osacat=0&_from=R40&_trksid=p2045573.m570.l1313.TR0.TRC0.H0.X1993+geo+metro+operators+manual&_nkw=1993+geo+metro+operators+manual&_sacat=0

or get an account at alldata.com
or join a real forum and ask there.
or google all week.
those are the DIY choices.

or google like this, google really is your friend....

https://www.google.com/search?q=1993+geo+metro+fuse+box&source=lnms&sa=X&ei=cxrNU7DaDMuTyASOrYCwAQ&ved=0CAcQ_AUoAA&biw=1120&bih=516&dpr=1.71



1994 Geo Metro | Answered on Jan 01, 2015


First stepwould typically be to replace the PCV valve. It's located behind the valve cover at the bottom of the rubber tube that connects to the back of the valve cover and branches off to the air filter housing.

Alternate possibility:

If the head gasket has been replaced, it's likely one of the oil returns is blocked (replacement head gaskets, for whatever reason, don't usually align with the head correctly). The solution is to open the secondary oil return. I used a one foot piece of 4 gauge bare copper wire (more of a 1/4" copper rod). Remove the valve cover. Taper the end of the copper wire to a blunt point and drive it about 6 inches down the oil return on the backside of the head near the rear of the head (directly behind where the oil filler cap was).

1994 Geo Metro | Answered on Dec 15, 2014


Circuit breaker box under the hood. Try replacing that breaker. Seems as though it's weak as heat gets to it.

1994 Geo Metro | Answered on Dec 15, 2014


Sounds like it's a Upper Valve Bearing. Is it a 1.3 L ?

1994 Geo Metro | Answered on Dec 14, 2014


wont go to high idle
this is the IAC failing not TPS, the tps only signals to the ECU
that you are at idle.

1994 Geo Metro | Answered on Sep 15, 2014


from what,. name it.
point with finger and say.. xxxxxxxxxxxxxxxxxx here.

1994 Geo Metro | Answered on Sep 14, 2014

Not finding what you are looking for?
1994 Geo Metro Logo

260 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1997 Geo Metro
1997 Geo Metro

236 Questions

1995 Geo Metro
1995 Geo Metro

215 Questions

1993 Geo Metro
1993 Geo Metro

168 Questions

1996 Geo Metro
1996 Geo Metro

168 Questions

1992 Geo Metro
1992 Geo Metro

151 Questions

Top Geo Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Metro Geo

  • Metro Geo

Most Popular Question

1994 geo metro automatic transmission

  • Cars & Trucks
Loading...