Hyundai Motor 2002 Elantra - Answered Questions & Fixed issues


Make sure the 3 prongs (2 silver & 1 gold) line up to connect properly when you put it back in. I had to pullout the gold outside of where the bulb sits and slightly pull out the 3 in the actual lens to get a good connection. ***This is what makes the turn signal wireless... They have to be aligned and have contact****

Hyundai Motor... | Answered on Jun 06, 2019 | 373 views


remove the interior door trim and you will see small nuts holding the handle onto the outer door skin. Remove any rods /clips and undo the nuts and the handle will come out.

Hyundai Motor... | Answered on Sep 29, 2018 | 309 views


The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

Hyundai Motor... | Answered on Jun 14, 2018 | 57 views


The brake light switch could be stuck.

Hyundai Motor... | Answered on Mar 12, 2018 | 17 views


hyundai elantra If you want to solve your problem, click on the link I attached

Hyundai Motor... | Answered on Dec 12, 2017 | 95 views


If the test says it the issue.. you have no choice but to replace it.. (you could cut it apart and clean it out, then reweld it)..BUT if the inspectors see it,, you are IN BIG TROUBLE!!

Hyundai Motor... | Answered on Sep 20, 2017 | 66 views


you have to mention the make and model that is being tested
there are codes but if it is a GM product many scan tools will not read the faults because it requires a scan tool with a special protocol for GM
if it is a nissan , the ECM has a small screw that has to be turned to get the codes to read
The car is playing so rest assured there are fault codes but who ever is doing the reading is using the wrong scanner or is not familiar with your make of car requirements

Hyundai Motor... | Answered on Sep 07, 2017 | 141 views


Sounds like the fuel pump is starting to go, the problem after fill up is most always related to a failing pump. The other issue may be a dirty throttle valve.

Hyundai Motor... | Answered on Jul 12, 2017 | 73 views


This issue is often caused by the PCV circuit. Check the PCV valve and port for clogging or torn/leaking hoses.

Hyundai Motor... | Answered on May 18, 2017 | 38 views


You don't say if you had it checked for DTC's - diagnostic trouble codes ? Have a scan tool that views sensor data hooked up . See what the PCM/ECM or TCM is see for input data . Your best bet mite be to take to a qualified repair shop that has the diagnostic equipment an knowledge to find the problem . Rather then guessing an just replacing parts .

Hyundai Motor... | Answered on Apr 21, 2017 | 83 views


The code says tps switch so replace the throttle position sensor.

Hyundai Motor... | Answered on Mar 12, 2017 | 330 views


Do you get power to fuel pump relay?

Hyundai Motor... | Answered on Dec 14, 2016 | 81 views


Did you recently clear the trouble codes or disconnect the battery? Once all codes are cleared, the computer will not display systems 'ready' until they go through an evaluation cycle. Some of the systems require a certain number of drive cycles before they will display 'ready'. A drive cycle is usually starting the engine from a cold start (based on coolant temperature) and driving until certain conditions are met. I don't know what the requirements are for your car, but my 2003 pickup truck requires more than 10 drive cycles before it will make the O2 sensors and evaporative emissions 'ready'. Most states only require that a certain number of systems are showing 'ready' to pass emissions certification.

Hyundai Motor... | Answered on Oct 24, 2016 | 173 views


The dome light is powered through 26A FUSE 26.
The clock and radio are powered through 15A FUSE 25 and 10A FUSE 9.

Hyundai Motor... | Answered on Sep 24, 2016 | 421 views


One is under the hood on the drivers side. The other is behind the little tip out tray by the drivers left knee. Open the tray and pull up to remove.

Hyundai Motor... | Answered on Jul 29, 2016 | 47 views


36mm socket and long breaker bar, 12mm and 14mm wrenches and a ball joint separator fork.

Hyundai Motor... | Answered on Jul 29, 2016 | 50 views


Best Manuals


to fix your car visit this link

Hyundai Motor... | Answered on Apr 06, 2016 | 94 views


Hi Dani, The links below are two short youtube videos that shows how to fix a car that doesn't start, The 1st link is a car that won't crank over and the 2nd link is a car that cranks over but won't start...CHEERS..
https://www.youtube.com/watch?v=TSE0fOrujW0https://www.youtube.com/watch?v=064Ilsz8Fzg

Hyundai Motor... | Answered on Mar 31, 2016 | 70 views


The VSS sensor is located on the transaxle .
If the VSS is defective replace the instrument cluster

Hyundai Motor... | Answered on Mar 20, 2016 | 950 views

Not finding what you are looking for?

653 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...