Question about 2011 Chrysler 200

1 Answer

How do I replace a headlamp? - 2011 Chrysler 200

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 76 Answers

    Follow these steps to change the headlight bulb on your vehicle:
    1. Open the engine compartment hood.
    2. Locate the back of the headlight to determine the lamp and bulb type.
    3. Decide which bulb you need to replace.
    4. Purchase the correct bulb for your headlamp.
    More items...

    Changing a Headlight ' DMV.org

    www.dmv.org > how-to-guides > headlight

Posted on Dec 04, 2015

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
bunnydawg

Roberta Smith

  • 5158 Answers

SOURCE: 2000 CHRYSLER CONCORDE HEADLIGHT BULB REPLACEMENT

thought i already answered this... must have been for someone else... you should be able to access the bulb from within the engine compartment... if it's on the side of the battery you may have to remove it. do not touch the bulb with your fingers as that shortens the life of it.

Robert

Posted on Jan 26, 2009

localwonder

Michael Masters

  • 6784 Answers

SOURCE: how do you replace the headlight bulb on a 2001 chrysler lhs.

This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Posted on Jan 28, 2009

jgwhomeequip

Jeremy Reddick

  • 1902 Answers

SOURCE: replacing headlight bulbs on a 2006 chrysler sebring

Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.

Posted on Feb 06, 2009

Anonymous

  • 1 Answer

SOURCE: headlight bulb replacement on chrysler 300m

Parts Required: Change all the lights at once, it is not worth the anguish of doing this over and over again
2 low-beam lights, 2 high-beam/running lights, 2 parking lights - part nos in the owners manual


A can of diet coke to clean the battery terminals is also recommended. *optional



Tools required

Ratchet set : 10mm, 7mm, 6mm sockets
Extension 12"
Large Flat screwdriver, small 4" flat screwdriver and a pair of pliers
Flash-light
12" Magnetic tip telescoping bit

Surgical gloves

Battery terminal cleaner * optional



Step 1:

First take off the plastic cover that cover that is across the front of the engine compartment. 6 push pins hold it in place, Use the long flat screw driver to pry them up and use the pliers to pull them off.


Gently take the plastic cover off and set it aside.


Step 2:

Next you will see 3 push pins that hold the front grill to the engine housing, using the long flat and a pair of pliers pull the 3 push pins out.


Step 3:
In the upper area of each wheel well, you will see a large 2.5" rubber grommet. Pull the rubber grommet out



Step 4:
Locate a 6mm bolt head that is driven vertically upwards. It is not visible looking at the wheel well. You have to lay down on the floor and you will find it about a foot below the grommet and at the edge of the fender. Use the the ratchet to remove this bolt headed screw. It is about a 1.5" long. Do this for both sides before going to the next step


Step 5:

Start with the passenger side as it is easier. Use the flash light and peer into the fender area from the engine compartment. You will see a nut on a bolt, and a plastic fastener.
Use the 10mm socket on the 12" extension. Insert it into the hole where the grommet was, and guide the socket on the nut head. It is about an 1" long. Be careful as you take it off, else you will be fishing for the bolt in the fender.

Step 6:
Pull on the plastic fender in the front till the bolt head and the fastener exit the fender. This has to be repeated for each side.

Step 7:
Locate 8mm bolt heads on top of the light assembly. Note it is not the Philips head - they are to level the lamps. Before undoing the bolts, check the spirit level on top of the lamp assembly and make a note of the bubbles position. You will need this when you put the assembly back. Undo both bolts, they have about an 1" of thread on the top and then you have to pull it up physically or with the use of the pliers

Step 8:
Pull the headlight assembly out - gently. Don't scratch the paint work and don't damage the rubber molding around the light assembly.

Step 8a*: If you see any salt build up on the battery terminals, pour diet coke or pepsi on the terminals, this neutralizes all the salt. Then pour some water to clean the gunk and then with a paper towel dry it. Be careful with the paper towel, as it contains sulfuric acid and is corrosive, put in in a garbage bag immediately. If you feel it has come into contact with your skin, was vigorously before continuing.

Step 9:
Note the position of the connector before you do anything. Turn the retaining rings holding each bulb counter clock wise. When you do this the bulb assembly and the connector will pull free. Two instances of this. Remove assembly, and place securely on a table

Step 10:
Locate the parking light below and turn the connector clockwise as you are looking over it. Pull out the old bulb and replace it. Do this for both sides. Turn on the parking lights to ensure they work, try the signals too. No sense it putting it all back together and nothing works. Replace the holder and bulb in reverse order. Note the unit should fit in nicely and rotate smoothly as you turn counter clockwise this time.

Step 11:
Using the 4" flat screwdriver, lift the locking pins gently and push the bulb out, Start with the low beams. Low beam has only 1 filament, high-beam/running light has 2 filaments. Put on the pair of surgical gloves, and open the pack of new bulbs, push the bulbs into the empty sockets, until the locking pins click into place. Change the low-and high beams.

Step 12:
Insert the bulb with the connector in the position you noted in step 9. Slide the mounting ring and then lock it into place by turning it clock-wise as you are looking at it from the rear of the assembly. Repeat this for both the high beam and low beam. Slide assembly back into cavity. Repeat this for the other side. Test the bulbs light correctly

Step 13:
Gently push back the front plastic so that the bolt and the plastic stud enter the fender. Pay attention to ensure that the fender lining sits correctly. Using the 12" ratchet extension and the 10mm socket mount the bolt back on and tighten. Do this for both sides

Step 14:
Using the ratchet mount the 6mm fastener on to the fender. Do this for both sides

Step 15:
Mount the jack screws on top of the headlight assembly. Tighten till the bubble in the spirit level returns to the original position. Don't push the bolt past its maximum. If it doesn't return to the original level, loosen and adjust the headlamp assembly and re-tighten. Do this for both headlamps.

Step 16:
Replace the 3 push pins that hold the front grill to the engine compartment. Replace the large plastic panel that was removed in step 1 and remount it using the 6 push pins.


Voila - you have changed all the bulbs on the front of the 1999 300M.

Estimated time:
Novice 2 hours
Advanced 1 hour
Expert 45 mins

If you found this helpful, a quick note to the author George and Anna at lmcgeko@yahoo.com would be appreciated.

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

How to change the headlight bulb on 2009 gmc sierra driver side


1. Loosen only, do not remove, the lower outside hidden headlamp bolt (2). 2. Depress the housing support tab with a flat-bladed tool downward in order to release the headlamp assembly from the support. 3. Pull the lamp assembly slightly forward to access the electrical connection. 4. Disconnect the forward lamp harness main electrical connector from the headlamp harness.
Headlamp Screws (Qty: 2)
1 Caution: Refer to Fastener Caution .
6 Nm (53 lb in)
O Headlamp Screw (Hidden)
6 Nm (53 lb in)
3 Headlamp Housing Support


Preliminary Procedure Remove Healamp
Remove either the LF or RF headlamp assembly. Refer to Headlamp Replacement (Chevrolet) Headlamp Replacement (GMC HD)
Headlamp Replacement (HD Diesel).
Headlamp Bulb (Hi)
Warning: Refer to Haiogen Bulb Warning .
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.
Headlamp Bulb (Lo)
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.

Need more come to https://www.autorepairhelp.us


change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-0.png change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-1.png

Aug 14, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

How to replace headlight bulb on 2002 chevy trailblazer


Headlamp Removal & Installation Bulb Replacement To Remove:
CAUTION
Halogen bulbs contain pressurized gas. Mishandling a bulb may result in the bulb shattering into flying glass fragments.
CAUTION
Make sure to wear eye protection when handling a halogen bulb.
CAUTION
Do not touch the glass of a halogen bulb, only handle the bulb by the base.
CAUTION
Do not allow a halogen bulb to come into contact with dirt or moisture.
CAUTION
Make sure to dispose of a used halogen bulb properly.
CAUTION
Do not allow children to handle halogen bulbs.
  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket counterclockwise.
To Install:
  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.
Headlamp Assembly Chevrolet To Remove:
Headlamp Assembly (Chevrolet) gm-06-00-1591.gif

  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp assembly.
  6. Remove the headlamp assembly from the headlamp panel.
To Install:
  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

Jul 20, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Headlight replacement - 2002 Trailblazer


  1. Open and support the hood.Remove the grille.
  2. Pull up on the retaining tabs (1) in order to remove the headlamp assembly from the headlamp panel.
  3. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
  4. Disconnect the headlamp electrical connector (2) from the headlamp assembly.
  5. Remove the side marker socket (4) from the headlamp assembly.
  6. Remove the park/turn socket (3) from the headlamp assembly.
  7. Remove the headlamp assembly from the headlamp panel.
  8. Installation:
  9. Position the headlamp assembly to the headlamp panel
  10. Index and seat the tabs on the park/turn socket (3) to the headlamp assembly.
  11. Index and seat the tabs on the side marker socket (4) to the headlamp assembly.
  12. Connect the headlamp electrical connector (2).
  13. Connect the headlamp leveling electrical connector to the motor/actuator if equipped.
  14. Align and install the 4 locator pins on the back of the headlamp assembly into the retaining tab holes.
  15. Push down on the retaining tabs (1) in order to lock the headlamp assembly into the headlamp panel.
  16. Install the grille. Refer to Grille Replacement .
  17. Close the hood

Oct 27, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

I need to change a dead bulb in my headlights and I dont have the owner manual.


96 sable, only ino I have. should be similar. Please rate, thanks

  1. sth~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    NOTE: A properly aimed headlamp (13008) assembly normally need not be re-aimed after installation of bulb. A burned out headlamp bulb and retainer (13N021) should not be removed from the headlamp until just before a replacement headlamp bulb and retainer is to be installed. Removal of a headlamp bulb and retainer for an extended period of time may allow contaminants (dust, moisture, smoke) to enter the headlamp and affect the performance of the headlamp. When servicing the headlamp bulb and retainer, energize the headlamp bulb and retainer only while it is contained within the headlamp body.

    Make sure headlamp switch (11654) is in OFF position.
  1. NOTE: On some models the clamps holding the integrated relay control module (IRCM) may need to be unsnapped and the module pulled aside to gain access to the driver side bulb.

    Open hood and locate headlamp bulb through hole in upper radiator support assembly.
  1. Remove headlamp wire connector from headlamp bulb and retainer by pulling the connector and wires in a rearward direction.
  1. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding headlamp bulb retainer off headlamp bulb and retainer. Keep headlamp bulb retainer as it will be used again to retain new headlamp bulb and retainer.
  1. Carefully remove headlamp bulb and retainer from opening in headlamp bulb (13007) by gently pulling straight out of opening. Do not rotate headlamp bulb and retainer during removal.
0a1a11c.gif

Jul 05, 2009 | 1991 Mercury Sable

1 Answer

Replacing headlight bulb of 2001 mercury villager?


SECTION 417-01: Exterior Lighting 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Bulb —Headlamp Removal
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Grasp the bulb only by its base. Avoid touching the glass envelope.
    NOTE: The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp.
    NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the headlamp bulb.
    1. Disconnect the electrical connector.
    1. Remove the headlamp bulb retainer by rotating it counterclockwise about one-eighth of a turn.
    1. Remove the headlamp bulb.
0deebe4.gif Installation
  1. Install the headlamp bulb.
    1. Install the headlamp bulb.
    1. Install the headlamp bulb retainer by rotating it clockwise about one-eighth of a turn.
    1. Connect the electrical connector.
------
go here for villager help

http://autos.groups.yahoo.com/group/villagerquest/

Apr 04, 2009 | 2001 Mercury Villager

1 Answer

Want to know how to replace my headlamp on my 1998 chevrolet silverado K1500 pick up truck. Do I have to remove the grille?


Nope! Here is the steps and a pic:


Headlamp Removal & Installation To Remove:
  1. Turn headlamp switch OFF
1afac03.gif
  1. Remove retaining ring screws.
  2. Remove retaining ring from headlamp.
  3. Remove headlamp from headlamp mounting bracket.
  4. Disconnect electrical connector from headlamp.
To Install:
  1. Connect electrical connector to headlamp.
  2. Install headlamp to headlamp mounting bracket.
  3. Install retaining ring to headlamp and install screws.

Mar 30, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

REPLACING HEADLIGHTS ON 93 GT


sorry, i only have 94 whcih is probably different. Hope it helps at least some.

Section 17-01: Lighting, Exterior 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Headlamp Assembly srb~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE BULB IS DROPPED. HANDLE BULB CAREFULLY. GRASP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP BULB OUT OF REACH OF CHILDREN.
Removal and Installation
  1. Place the headlamp switch (11654) in the OFF position.
  1. Remove the electrical connector from the miniature bulb (13466) by pulling it rearward.
  1. Remove three nut and washer assemblies from the rear of the headlamp (13008) .
  1. Remove the headlamp by pushing forward on the headlamp bulb and retainer (13N021) assembly. For ease of removal, it may be necessary to loosen the attachments of the adjacent parking lamp (13200) and cornering lamp assemblies.
  1. Remove the three clips attaching the headlamp to the headlamp bulb retainer (13N019) by prying them out from the base using a flat-blade screwdriver. This completes the removal of the headlamp . Save the clips for the installation of the new headlamp .
  1. To install the aerodynamic headlamp , ensure that the black rubber shield is securely crimped to the headlamp , then reverse Removal procedure.
  1. After headlamp installation, check headlamp aim and adjust as necessary as outlined under Adjustments.
  1. Turn headlamp switch on and check for proper operation.

    7376770.gif


    Item Part Number Description 1 13200 Parking Lamp Assy 2 14290 Headlamp Dash Panel Junction Wire 3A N621906-S301 Nut (2 Req'd) 4 13A093 Headlamp Adjustment Screw and Nut Assy 5 13008 Headlamp Bulb A Tighten to 4.4-6.4 Nm (39-57 Lb-In)

Mar 21, 2009 | 1993 Ford Mustang

1 Answer

Instructions on replacing headlight assembly


96 f150 procedure

Headlamp Assembly Removal
  1. Remove radiator air deflector from radiator support.
  1. Remove two screws and two nuts retaining headlamp door (13064).
  1. Pull headlamp door from vehicle. Remove three bulbs and sockets.
  1. Disconnect engine control sensor wiring (12A581) from headlamp bulb (13007).
  1. Remove two retainers attaching upper two attachments of headlamp (13008).
  1. Turn horizontal headlamp adjusting screw (13032) completely out of the adjusting nut.
  1. Pull headlamp from vehicle.

Oct 17, 2008 | 1994 Ford F150 Styleside Supercab

1 Answer

Headlamp replacement


Remove or disconnect the following: hood close out filler panel, bolts from the headlamp, headlamp from the headlamp mounting, electrical connector from headlamp, bulb retainer ring from headlamp assembly, then bulb from assembly

Oct 07, 2008 | 2002 Chevrolet Cavalier Coupe

Not finding what you are looking for?
2011 Chrysler 200 Logo

Related Topics:

2,660 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...