Question about 2006 Ford Fiesta 1.4

1 Answer

I need torque setting for 1.4 duratec engine for the conecting rod and main bearings

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,440 Answers

A cheap shop manual will have this and so much more. This information is so critical you might not want to rely on someone's memory.

Posted on Mar 15, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
chuckster57
  • 1102 Answers

SOURCE: Need torques specs for main

Main bearing torque is 56-62 Ft/Lbs..I would use 60
Rod bearing torque is 23-28 Ft/Lbs..I would use 25

Posted on Jan 15, 2011

moparownr
  • 667 Answers

SOURCE: main and rod bearing torque specs

do you have a Haynes Manual or Chilton? if not check your local library, they may have one, the specs are in there

Posted on Mar 31, 2009

inspectmycar
  • 233 Answers

SOURCE: Needing engine bolt torque specifications for a

stage 1 tighten to 30 ft pounds
stage 2 tighten 90 degrees
stage 3 loosen one full turn
stage 4 tighten to 30 ft pounds
stage 5 tighten 90 degrees
stage 6 tighten 90 degrees
this is per mitchell on demand courtesy of ford specs on the lft and right head.
for some reason there are no torque specs on mitchell for connecting rods and mains.

Posted on Sep 16, 2009

  • 1 Answer

SOURCE: i need to know the torque settings for 850cc reliant robin

go to
http://mankymonkeymotors.co.uk/Trikespageimages/relianttorquesettings.html

a target="_new" href="http://www.leafletflyers.co.uk/">Leaflet Distribution in Croydon</a>, Leaflet Distribution in Balham, <a target="_new" href="http://leafletflyers.co.uk/Leaflet-Distribution-Streatham.htm">Leaflet Distribution Streatham</a>.

Posted on Aug 08, 2010

wfservices
  • 262 Answers

SOURCE: NEED TO KNOW WHAT ARE THE TORQUE SPEC N A F250

I hope this helps you. WF

  1. Install the main bearing cap bolts and the cross-mounted main bearing cap bolts.
  1. Tighten all of the main bearing cap bolts in two stages.

    Stage 1: Tighten the vertical fasteners 1 through 10 to 37-43 Nm (27-32 lb/ft). Rotate fasteners 1 through 10, 85-95 degrees.

    Stage 2: Tighten the cross-mounted fasteners 11 through 20 to 27-33 Nm (20-24 lb/ft). Rotate fasteners 11 through 20, 85-95 degrees.

935da7d.gif
Tighten the connecting rod bolts in two stages, using the sequence shown.

Stage 1: 40-45 Nm (30-33 lb/ft)

Stage 2: Rotate 90-120 degrees

7e9368a.gif

Posted on Aug 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know the torque settings for the big end shell bearing caps


if you have a rebuild kit. the specs are listed in the instructions.. if not call the parts store with engine info and they can tell you...

Feb 15, 2013 | Toyota Celica Cars & Trucks

1 Answer

Torque specs for rod & main brgs for 1994 ford f150, 300 6 cyl fuel inj engine


Main Bearing Cap Torque:
Torque in 2 steps: Step 1: torque to 35 Ft/Lbs Step 2: torque to 70 Ft/Lbs

The Rod Bearing Cap Torque: 45 Foot pounds (Final torque)

Was this what you needed...let me know by your rating of me...thanks!

Sep 17, 2011 | 1994 Ford F150 Styleside Supercab

1 Answer

I need the torque specs for the main bearing and conecting rods for a 2000 chev S-10 W/2.2L engine code (4)


I show the main bearing torque to be 70 ft.lbs.
The rod caps are torqued to 38 ft.lbs.
Best of Luck to you..

Aug 26, 2011 | 2000 Chevrolet S-10

1 Answer

What is the torque specification on the main and conecting rod bearing of an isuzu npr 4bd2?


Main bearing caps 116-130 ft-lbs
Connecting Rods 58-65 ft-lbs

This is for the 2.2L Diesel engine.

May 04, 2011 | 1995 Isuzu Rodeo

1 Answer

Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

Mar 02, 2011 | 1989 Honda Civic

1 Answer

I am looking 4 the torque pressures (ft.lbs) on the main crank bearings, and rod bearings on a 2007 Ford 5.4 3 valve engine??? Gerry..............thank-you


mains - vertical bolts first 30 ft.lb. PLUS 90 degrees
pattern frt

8 7
4 3
2 1
6 5
10 9
side bolts
22 ft. lb plus 90 degrees
pattern frt

7 8
3 4
1 2
5 6
9 10

connecting rod caps cracked type rod-rod and caps must be kept in matched sets, recommend new bolts/nuts, spec is 32 ft lb. plus 105 degrees - torque each item to the correct torque then go back and do the degrees. these are torque to yield bolts and the procedure is very important.

Oct 02, 2010 | Ford F-150 Cars & Trucks

1 Answer

Need torque for a 2000 Toyota Celicia GT 1.8L


Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Mar 18, 2010 | 2000 Toyota Celica

1 Answer

I need the torque specs for the main and rod bolt for a 99 escort 2.0l engine


engine tightening torques
Main bearings Renew bolts/nuts No
Main bearings Stage 1 43 Nm
Main bearings Stage 2 85 Nm
Big end bearings Renew bolts/nuts Yes
Big end bearings Stage 1 15 Nm
Big end bearings Stage 2 90°

Jan 21, 2010 | 2004 Ford Focus

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

Not finding what you are looking for?
2006 Ford Fiesta 1.4 Logo

Related Topics:

1,980 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...