Question about 2000 Buick Park Avenue

1 Answer

Power door lock switch replacement

How do i get my buick park ave door panel off so i can replace my broken power door lock switch ? I have a 1997 Buick Park Ave.

Thanks

Posted by on

  • Anonymous Mar 16, 2014

    my 1995 buick park ave will not start after just shutting off

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers




Remove or Disconnect

Door handle trim plate.

  1. .Install or Connect

  2. Electrical connector and door lock cable.
  3. Trim panel by engaging hooks on backside of panel.
  4. Push pin fastener in defroster duct.
  5. Screw from behind lamp assembly.
  6. Courtesy lamp assembly.
  7. Two screws in arm rest.
  8. Arm rest cover plate.
  9. Door handle trim plate.
There May Be A Need to Drill Out RIVETS that Hold Motor in place,. Just Replace with>>MACHINED SCREWS & BOLT'S




Remove or Disconnect

  1. Trim panel. See: Doors, Hood and Trunk\Doors
  2. Four tabs retaining switch.
  3. Electrical connector.
Install or Connect

  1. Electrical connector.
  2. Snap switch into trim panel.
  3. Trim panel.

Posted on Mar 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Buick Park Ave Power windows, Power door


see the diagram attached. test the cables, connector, for open, dirty, bad contacts. Switch, test for bad contacts, clean with contact cleaner, and finally test the motor for open or faulty.Test the fuse or . c.breaker for open or faulty, and clean contacts.
God bless you65149ed9-f8de-443f-9f07-8a66d9d5bcca.jpgc7045ddc-d17c-4b28-8195-9bc37cb53c49.jpg

Sep 30, 2013 | 2002 Buick Park Avenue

1 Answer

Timing chain replacement 1997 buick park ave.


They are not prone to fail. I always recommend to replace only major when engine repair is needed.

Mar 27, 2013 | 1997 Buick Park Avenue

1 Answer

1997 buick park ave/driver side window doesnt work / i replaced the window switches but still doent work


I remember replacing a lot of power window motors on Buicks,but not a lot of switches.Use a basic 12v test light to verify everything is OK to the motor.

Jul 06, 2012 | 1997 Buick Park Avenue

1 Answer

My back windows wont go up and the doors wont lock. door ajar light pops on


Will the windows go up and or lock from the respective doors? Is this the master control on the driver that does not respond? If so remove the driver door panel ( see 97 Park Ave door lock for instructions ) and check the wireing harness located under the switch control panel, make sure all are pluged in well and are not damaged. If the wireing harness is in good repair You might want to check salvage yards for the appropiate control switch replacement. ( watch them remove it from the junker and you'll know how to install it )

Jul 08, 2009 | 1997 Buick Park Avenue

3 Answers

1997 buick park ave 4 door right front door handle won,t work from the outside


Order the exterior door handle AND the clip that attaches the rod to the exterior handle from your local dealership ( any part in the salvage yard will have at least as much wear as the one U are replacing ) Also order a can of touch up paint matching your car. After you have the parts and have painted the new exterior handle, roll down the window and remove the interior door panel. ( instructions have been posted at 'replace door lock buttom' ) Two nuts, one on each side, hold the broken handle in place and must be removed ( DON'T loose them ). Loosen the rod from the clip at the top to allow a bit more room, But take note on the way it is attached ( you will need to reattach the rod to new handle ) To install new mechanism put the new clip on the rod, carefully place the gasket and the new handle in place and install nuts to secure. Test the door handle and make sure it works. Reinstall interior door panel.

Jul 06, 2009 | 1997 Buick Park Avenue

1 Answer

1997 buick park ave door lock buttom is loose. How do I remove the drivers side door panel?


At the bottom of the door panel you will find several screws ( haven't removed mine in a few mo. and have forgotten how many ) there are also screws under the slotted bottom of the finger grip in the door panel. After removing screws lift the panel from the bottom and to the top of the door. You will encounter clips on the rear of the door panel the most problematic is by door locking mechanism. Use a small blade flat screwdriver to Gently prise the clip out of the metal door. To pass over the interior door handle piviot the door panel, Take Care the wires for window and door lock are located here!
I used Gorilla Glue to reseat my lock button be Cautious not to bind the lock button, or the function will be impaired ( won't work ) HAVE FUN

Jun 29, 2009 | 1997 Buick Park Avenue

1 Answer

Need the location of the horn fuse for 1995 buick park ave ultra


For the right side the fuses are
1 Door Locks, Trunk Pull-Down, Fuel Door Release
2 Power Antenna, Lock Switch, Trunk Release
3 Horns
4 not used
5 Cruise Control, Misc. Engine Controls
6 Fuel Pump
7 Injectors
8 Powertrain Control Module, Pass-Key II
9 Not used
10 Not used
11 A/C programmer
12 Not used

The order for the fuses go up in down in columns. First row 1-4 etc.

Jun 24, 2009 | 1995 Buick Park Avenue

1 Answer

1998 buick park ave door opens from inside not the outside


you most likly have a broken lock rod clip inside the door. you can remove the door panel and look around the latch and you will find your problem.

Jun 04, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

None of the interior lights work, cannot find switch/fuse


Take off panel under glove compartment and fuse box is up high and to the far right of the car almost out to the door. Will have label, cover just snaps off.

Nov 23, 2008 | 1997 Buick Park Avenue

Not finding what you are looking for?
2000 Buick Park Avenue Logo

790 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...