Question about 2005 Peugeot 405

1 Answer

Removing Peugeot 407 Petrol 1.8 Spark plugs

I know how to do spark plugs but the housing around 407 plugs looks a little complicated. Any help would be appreciated.

Thanks

Des

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fiat punto 2005 spark plug change


Hi Gerard, on a 1.28v Punto the plugs are on the back of the cylinder head tucked between the 4 inlet manifolds. The plug closest to the timing belt end (just next to the oil dipstick) is easy to find, the others are a bit obscured by the plastic housing that sheaths the injector wiring. Be careful pulling off the suppressor caps, they hang on quite tight so best use long nose pliers and NOT pull on the HT lead. Hope that helps. Andy

Apr 15, 2014 | 2005 Fiat Punto 1.2

1 Answer

2005 Pt Cruiser running poor at acceration


If plugs helped...the problem went away...then it could be a plug getting fouled by excess fuel or oil. Look at your new plugs and see if they are discolored or went with gas. could be an injector problem. It could also be an ignition problem. You moved the plug wires around and they worked for a few minutes till the new "connection in the wire" burned up. Check your plug wires with an ohm meter. Check your plugs for fuel or oil on plug...a sign of stuck injector, oil leak, misfire. Did it really help or was it just wishful thinking?

Apr 02, 2014 | 2002 Chrysler PT Cruiser

1 Answer

My mazda v6 mx6 2.5, automatic misfiring. what could be the problem


what year and how many miles? check engine light on? problem could be as easy as a spark plug wire loose or broken. so first check for broken or loose spark plug wires check them close with your hand. u can also check at night time with the engine running, watching for an out of place spark. next i would check the spark plugs, remove and inspect for proper clearances. still no luck u can do a compression test on each cylinder. fuel delivery could also be a problem but a little more complicated to check. u could always put some fuel injector clean in ur fuel tank. ps if u take ur spark plugs out look at the spark plugs tips. compare the spark plugs with a spark plug condition chart. also always use anti seize compound on the threads of your spark plug before installation.

Aug 02, 2013 | Cars & Trucks

2 Answers

My car smells like its burning oil, and there is oil in my spark plug wells. Guy at auto parts store says I need to replace oil gaskets that go around spark plugs. Is this a valid diagnosis and if so is it...


As far as I know spark plugs only have a metal type washer to seal, and there is no other oil seal needed. I have know oil to leak from rocker cover and fill spark plug wells, but tis also often covers engine. Burning oil smell couldbe from oil going onto the outside of hot engine. Check oil loss via dip stick. Clean all oil from outside engine to find out sites of leaks. Hope this helps.

Sep 22, 2017 | 2004 Volkswagen Jetta

3 Answers

97 sebring 2.5. need to know where the crank sensor is. not getting fire to plugs


Hi, the crank sensor goes into the top of the bellhousing, right at the back of the engine where it meets the transmission. You may have to remove the air filter housing and hoses to see it. It reads on the flywheel.

sheikhtijani.jpg

May 14, 2011 | 1997 Chrysler Sebring

1 Answer

Spark plugs


The heat shields are attached to head under spark plug. Need to turn boot on wire all around & then wiggle back & forth & pull upward.

Jul 13, 2010 | 2004 Chevrolet TrailBlazer

2 Answers

I had replaced spark plugs with NGK BKR6E-11. The fuel economy has gone down dramatically after this change. The plugs I was using earlier were NGK BKR6E-11 and then the mileage has now gone down. Now I am...


You are correct in saying the gap. Call a suzuki dealer, ask for service and as what the gap should be. Your problem is more than likely not having set the gap. Before you change that gap, if you can, measure what is now vs/what it should be. You will need a feeler gauge. Grainger sells the, so des NAPA.

Dec 08, 2009 | 1999 Suzuki Esteem

2 Answers

Spark plugs change


remove the spark plug lead from the plug, blow out any dirt etc from around the plug, undo the plug and remove from the vehicle, make sure the plug has the right gap setting before installing into the engine.
Check each plug that you remove for any sign of a wet or oily plug which are signs of more serious problems.
If all the plugs are dry with just a light brown carbon deposit on them they are firing ok.
Hope this helps

May 22, 2009 | 2006 Suzuki Forenza

1 Answer

Nissan ca18det wont start


try looking near the bottom pulley or around the gearbox housing near to where it bolts to the engine

Jan 26, 2009 | 1988 Nissan 200SX

4 Answers

How to change the spark plugs in a 2006 Volkswagon Jetta


The solution is:

Engine cover removal: Fairly simple, I will try to explain this best I can without pictures. To start, you will want to remove the connecting air intake hoses (BIG tube looking thing on bottom right of the top of the engine) it is clamped down, just take some pliers and unclamp it to remove hose. Then the hose right next to that one (adjacent to the front bumber) You will need an star screw driver, if you look at the two screw's heads on either side of it you will know what i'm talking about. Then that comes off. Then there is a wire attached to the air intake hose, you must unconnect it, (I explained already how to take wires off in the spark plug section below, they are all the same) Next all you have to do is pull up on one side of the engine cover. (if you look at the back left of the cover you see what looks like a rubber gromet, kinda of look like you need to take that bolt off just to get anywhere.. you don't, that rubber peice acts as a snap on button say on your shirt perhaps) You pull hard enough it will come up, and there is four of those rubber gromet fasteners so just keep wiggling it and pulling until you get it off.

Spark Plug removal:

The spark plugs are located on the very top in plain sight of the engine, easy easy to get to.. you will see (not the actual spark plug just sitting there staring at you, they are under the caps) There are five caps all facing the same way and they have wire connections hooking to all of them. First you have to unconnect the wire to the cap. Take a skinny flat head screw driver.. and stick it in the middle of the wire housing (don't get confused, the housing is just the plastic piece that is black, it "houses" all the wires that power the spark plugs) The middle of the wire housing you will see a little perfect sqaure opening, there is a little clamp thing in there and with the screw driver all you do is put pressure upward (toward the back of your car) and pull at the same time and the housing will disconnect from the spark plug cap. Do this to all five caps.

Next the cap itself, is really easy to take out, just use that same flat head screw driver to kind of pry underneath the cap, don't be afraid to put pressure you won't break anything, Then the cap will come off and underneath the cap (attached to it) is the spark plug covers (acts like.. a battery in the remote) long metal tubular looking things.. if you see that, your doing good. Now look down into the whole you just removed the spark plug cover from, you will see the top of the spark plug down in there. Do this for all five caps.

Now you need tools, a medium size wratchet would do good. make sure you have a loong extension, and a deep well (long) socket (size in MM is 15 in standard 9/16 or one higher) loosen (lefty loosey, righty tighty) the spark plug until you can pull it out with the wratchet.. discard old, put in new spark plug, tighten but not tight tight.. do that for all five spark plugs.. once new spark plug is in, put the spark plug cover and cap combo back into the whole ( MAKE SURE YOU CLEAN IT AND THE WHOLE OUT BEFORE HAND) then just apply little pressure and the cap will set back into place (just make sure it is facing the way it was before) then connect the wiring back to the end of the cap (just slide it on and push it will "click" into place) do that for all .. then put your engine cover back on, reconnect the hoses and the wire on top of the hose. You are then good to go.

Oct 17, 2008 | 2006 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,042 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

scj103

Level 2 Expert

99 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...