Question about 2000 GMC Envoy

1 Answer

Front brakes I have had several issues with my brakes. The front brakes (especially driver side) gets hot and smokes but is not leaking anything. We have bled the brakes, replaced the brakes, replaced hose lines and calipers. Was told it could be master cylinder but with what I have found it does not seem like that. It seems like brake pressure wont release unless the car sits awhile and then is okay for a short distance then acts up again. Today i had to almost floor the gas just to get it up to 40 because it dropped from 55 to about 40 on its own and the rpms sky rocketed. I was also told it could be the abs proportioning valve but from what i have been reading they are for the rear brakes. can someone help me please?

Posted by on

  • brit s Jun 25, 2013

    for some reason its like the brakes do what they want. if i remove my foot from gas on an incline it actually stops and sits there, i dont even have to touch the brake. any clue whats going on?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • GMC Master
  • 22,423 Answers

If the proportioning clogs or damaged it can cause brake problems such as yours take pressure readings on all 4 calipers the proportioning valve is just as it says differentiates the pressure front to back also the abs unit itself can cause the same problem also

Posted on Jun 26, 2013

Testimonial: "thats kinda what we were thinking so we actually unplugged the abs to see if it made a difference and its still messing up. we are gonna flush the brake system and see what that does and plug the abs back in. i do believe the abs unit is a salvage part. its been wrote on with a yellow marking saying 2000 blazer and i know it wouldnt come out stock like that so maybe its already had issues with the abs before we bought it. ive dumped atleast the same amount of money into it as i paid and its costing me like $80 a week in gas to go to and from work which is only about 12 minutes away so its robbing the gas mileage bad"

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 9 Answers

SOURCE: 1986 gmc sierra 1500 front rt brake locks up

check brake lines they may have gotten pinched very commonok new c/k trucks when you crank the torsion bars up to far you may have hit something and pinched the brake line check those before messing with the master cylinder those are a real pain

Posted on Sep 21, 2008

  • 266 Answers

SOURCE: replaced both front calipers, rotors,

The best way to bleed the brakes is to start with the master cylinder and work your way back. after you are sure all the air is out of the master, got to the rear and open one bleed screw. do not touch the brake pedal ,but let the fluid drain, keeping the master cylinder full, untill the fluid comes out clear,like new. Close that side and go to the other rear wheel and repeat. After the rear is done close all beed screws and pump the brakes at least 10 times .Then bleed the front in a normal fashion. Try to close the bleed screw before the brake pedal hits the floor.If you still have air in brake system then there has to be a leak letting it in. Gravity brake bleeding is the easiest way to remove air in system

Posted on Mar 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drove my Honda Passport AWD 2002 about 7 miles this morning and I noticed smoke that seemed to be coming from the front wheel on driver side. What could it be?


Wouldn't you suspect a failed wheel hub
bearing assy or brake issue ?

Start taking it apart & sniffing as you go

Have to stop using it as is

Oct 19, 2014 | 2002 Honda Passport

1 Answer

Brake booster vacuum leak


Your brakes appear to be dragging i.e. brake pads still contacting the rotor. It could be air in your hydraulic braking system. Have the braking system flushed and bled.

Jan 17, 2014 | Audi Cars & Trucks

2 Answers

Ford 2004 f250 king ranch v10 6.8 brakes are not working.


In this case, you will need to leak the for wheels, never leak only one or two wheels when adjusting the breaks. If the leaking continues you need to check the conduit for potential damages. If pedal stay soft after checking everything else, check the break fluid unit. The unit has a piston if I'm not wrong. The piston has some parts that are of rubber material which can wear out or get damaged.

Nov 22, 2017 | 2004 Ford F250

1 Answer

I have no front brakes on my 88 Toyota. I've bled


You may have to install brake cylinder kits on the front wheels. The kits come with all you need to replace them. Or it could also be the main cylinder that's leaking.

Nov 20, 2011 | 1988 Toyota Pickup

1 Answer

Callipers on passenger side front and rear had locked down while the car sat on millitary base for nine months. Purchased new callipers (all four) pads rotors etc to get my sons car back on the road. Now...


Sounds like the master cylinder has bailed on you as well. Pedal going to the floor is the common sign that it's bad. To prevent any more aggrevation's, match the part, port for port, size, shape, and mount flange before putting a drop of fluid in the new one. It's a critical part and should obtained from Hyundai. Have it pressure bled, or have the dealer do it. The ABS sometimes requires special equipment to bleed the system.

Aug 27, 2011 | 2006 Hyundai Tiburon

1 Answer

Drivers side front brake pads sticking, smoking bled allready no help


Sounds like you need new calipers and or the rubber portion of the brake line that goes from the steel brake line to the caliper. This part of the brake line (rubber part) can colapse inside acting as if there is a one way valve in the line keeping pressure on the caliper piston as if the brakes are applied.

Nov 28, 2010 | 1991 Cadillac DeVille

4 Answers

1997 JEEP GRAND CHEROKEE FRONT BRAKE GETS VERY HOT SMOKES. CHANGED BRAKES AND ROTORS BOTH SIDES NOW OTHER SIDE DID IT. wHAT MAY BE CAUSING THIS/


Were the calipers check for not sticking, as well as lubed well when re-installed? If it's original flex hoses at calipers, that's also a consideration.

Jan 01, 2010 | 1997 Jeep Grand Cherokee

1 Answer

I have a 94 cavalier rs and i put a rear wheel cylinder in it and i started to bleed the brakes and i bled the right rear and it bled fine then i went to the side where i put the wheel cylinder in and it...


well sounds like its still full of air youll have to gravity bleed it. if you can leave your car on a steep hill overnight with the rear end up then bleed it the do the same make your front end sit high up overnight then bleed it. air bubbles always try to make their way to the highest point

Oct 19, 2009 | 1994 Chevrolet Cavalier

1 Answer

Brakes still spongy


need to perform abs service bleed, as far as i know only the dealer can do

Jul 02, 2009 | 2006 Chevrolet Malibu Maxx

Not finding what you are looking for?
2000 GMC Envoy Logo

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...