Question about 1999 GMC Jimmy

1 Answer

I have no brake pedal in my 1999 jimmy i replaced both back calipers still no pedal

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 2,361 Answers

Ask a friend to help pump the brake while you look underside for leaks.
KEEP brake fluid reservoir fill!

Do a complete bleeding.

Posted on Jan 20, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 226 Answers

SOURCE: How do i properly bleed out my Jimmy?

I use a vacuum bleeder (abt $35) starting at the furthest brake line from the master cylinder & working my way back to the closest. If bled properly by keeping the maste cylinder full, this should solve your problem. Rick

Posted on Apr 15, 2009

  • 532 Answers

SOURCE: Brake problem

air in the lines,bleed them,check rear brakes

Posted on Apr 18, 2009

  • 14092 Answers

SOURCE: 1999 GMC Jimmy Rear Brakes

where do you live meaning if you live on mountain or driving down steep incline every day you will ride brakes every day.that will wear on them a lot.use manual low1 gear coming down mountain.also buy a good brand brakes .i learned a long time ago if you pay more .it will last more.longer.

Posted on May 24, 2009

  • 1201 Answers

SOURCE: Brake pedal still goes to floor 2000 GMC Jimmy

It's very possible to be the master cylinder, the o-rings on the piston could be worn, letting the fluid seep back through instead of getting full pressure through the lines. Could also be the brake booster.
Try changing the master cylinder first, which is cheaper and easier, and see if there is a difference, you'll need to bleed the brakes again.
To check the booster,
With the engine off, pump the brakes until the pedal is hard, then hold pressure on the brake pedal and listen for air escaping, or the pedal goes slowly to the floor, Do that after the master cylinder has been changed, at least that will be eliminated.

Posted on Sep 15, 2009

Testimonial: "Hadn't thought about the O-rings on the rod thanks for the idea. Great Idea Thanks!"

  • 1985 Answers

SOURCE: 1997 GMC Sierra 5.7 changed master cylinder

check under your master cylinder,is there another clyinder below with one line in and one line out,if you do I found this is for the Abs to the rear,I had to replace this it was full of air,and did exactly what yours is now

Posted on Dec 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause the Brake Calipers to stick and get my Rotors hot on my 1999 GMC JIMMY


The master cylinder. What you have is something that is pressurizing the front brake circuit but not the rear. The only possibilities would be the Master Cylinder or a proportioning valve.

May 07, 2016 | 1999 GMC Jimmy

1 Answer

Replace front brake discs


Remove wheels.
Remove calipers and caliper mounting brackets.
Remove brake disk.
Replace new disk, being sure to clean it thoroughly with brake cleaner and a clean rag.

Replace caliper mounting bracket.
Replace new brake pads.
Push back caliper piston.
Re-attach brake caliper.

Repeat on other side.

Remove brake fluid reservoir cap.
Pump brake pedal until hard.
**** out any excess fluid from master cylinder reservoir.
Replace cap.
Wash off any excess fluid with water and dry thoroughly.

Road-test

Be sure to keep to a slower speed than usual and keep extended braking distances until new pads and disks are bedded in.

Nov 07, 2012 | 1999 Daewoo Matiz

1 Answer

98 jimmy slows down and stops on its own.


If the brakes are stopping the jimmy, it could be a hydraulic problem. check brake fluid level in master cylinder. If it is overfilled, fluid can expand when fluid heats up and can apply brakes. also,bad brake hose can trap pressure in caliper and apply brakes. Also check brake pedal and booster adjustments. other possibility is caliper/hardware (mechanical) is hanging up and not releasing. If drum brake in back, check adjustment and/or stuck wheel cylinder.

Jun 20, 2012 | 1998 GMC Jimmy

1 Answer

My 1999 GMC Jimmy's ABS light comes on and off and then the car makes a humming sound. When I press the brakes the car begins to stop, but then the pedal drops to the floor and the car keeps going. I...


Make sure your your wheel speed sensors have good connections at the wheel since you just did work there. You may need to bleed the brakes again for the other problem.

Aug 10, 2017 | 1999 GMC Jimmy

1 Answer

New brakes everything new blead brakes still no pedal


Did you replace the brake calipers? If so, the calipers are left and right specific. Even though they can be mounted on either side, make sure the caliper bleeder screw is on the top portion of the caliper when mounted on the vehicle or else it will be impossible to completely bleed the air out.

Jan 22, 2011 | 1996 GMC Jimmy

1 Answer

Instructions for replacing front disc brakes.


Jack up the car, support with a jack stand. Remove the wheel, unbolt the 2 bolts on the back of the caliper, and remove the caliper and pads off the rotor. Then with a large C-clamp or caliper piston tool and the old brake pad, push the brake piston back into the caliper until it is completely seated, install the pads, lubricate where the calipers slide and reinstall. Make sure to pump the brake pedal after you are done to get the new pads against the rotors before driving.

May 22, 2010 | 1998 GMC Jimmy

1 Answer

Turned rotors and replaced pads now it locks up why on 99 jimmy


Providing you do not have an ABS or Brake light.Either you have a leak, ( which should have set off a brake light) the calipers are defective, the rubber hoses leading to the calipers are so worn that they are deteriorating from the inside and are causing a blockage., or the fluid needs to be replaced and the system must be bled.

Mar 31, 2010 | 1999 GMC Jimmy

1 Answer

Removal and replacement of brake shoes 1999/2000 on ford escort e


Hi
Firstly put the hand brake on and loosen the wheel nuts, jack the car and remove the wheel, if you turn the wheels out so you have a better view. then remove the 2 10mm bolts from the rear of the brake caliper, there will be a hard tough wire coming over then brake caliper pop this off with a screw driver or pliers. now open the bonnet and remove the cap from the brake fluid bottle. once done leave it off and then retun to the brakes, get a flat screw driver and place it between the inner most brake pad and the brake disc then push the 2 apart, once these have been moved lift the caliper off and the brake pads should come free. the caliper has a cylider/ round part that pushes the pads against the disc ensure that the cylider is pushed right back into the caliper using some big grips large pliers. once the cylinder is right back you should be able to fit the new pads. replace all the parts in reverse order, but before putting the wheel back on push the brake pedal several times until the pedal feels hard. then replace the wheel and do the other side. once complete check the fluid level on the brake fluid and replace the cap.

This is a fairly easy job should take a novice about 40mins a side but if your quite savvy with cars then you can complete the whole job in about an hour.

Hope this helps if not please get back to me so I can be more accurate, and talk you through it.

Regards
Dan

Jan 31, 2010 | 1999 Ford Escort

2 Answers

Brakes on 200 GMC jimmy


get a bleed kit or make up some with clear plastic tubing fitted to each bleed nipple
run tubing into a clear dispoable container for each with enough fluid in them so as not to allow air back up the tubing! 2inches deap should do it so long as the tube cant move out of the fluid!
then you can open all four nipples & slowly pump the pedal & dont lat the master cylinder get too low on fluid! [dont pump hard or fast as it creates bubbles]
when no air is left in the system [no bubbles in jars or tubing then close all nipplse!
allow a couple of minutes for the rubbers to settle to original shape then you should have pressure at the paedal!
Cheers Rob

Aug 16, 2009 | 1999 GMC Jimmy

1 Answer

Brake problem


air in the lines,bleed them,check rear brakes

Apr 18, 2009 | 1998 GMC Jimmy

Not finding what you are looking for?
1999 GMC Jimmy Logo

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...