Question about Cars & Trucks

1 Answer

How to bleed clutch master cylinder

Where is the bleed screw

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,361 Answers

The bleed screw is on the salve cylinder (lower part)

Posted on Jan 21, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Hydraulic clutch problems

i have a ktm 125 wich all ktms have hydraulic cluthcs and i have the same problem as all these fellas even when im riding it just sucks right down all the fluid reply to me on X-KTMrida-X@hotmail.com ok thanks fellas

Posted on Oct 27, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

  • 1596 Answers

SOURCE: How do I bleed the clutch master cylinder

Same as You Bleed Any other System Being carefull not to get air IN and IT sometimes TAKES FOREVER ________ STICK WITH IT ------ Took Me 2 hours One time

Posted on Jan 19, 2009

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed brakes?


If YOU DON'T HAVE AN AUTOMATIC BLEEDER GET SOMEONE TO HELP YOU. MAKE SURE THERE IS FLUID IN THE RESOVOIR. HAVE YOUR HELPER 'PUMP' THE BRAKE PEDAL NUMEROUS TIMES THEN HOLD THE PEDAL DOWN. STARTING FROM THE FURTHEST WHEEL AWAY FROM THE RESEVOIR OPEN THE BLEED SCREW SLIGHTLY TO LET OUT ALL AIR. CLOSE THE BLEED SCREW AND PUMP UP THE LINE AGAIN HOLDING THE PEDAL DOWN OPEN THE BLEED SCREW AGAIN UNTIL PEDAL GOES TO FLOOR. CLOSE THE BLEED SCREW AND REPEAT UNTIL NO AIR COMES OUT. MOVE TO NEXT WHEEL AND REPEAT. MAKE SURE YOU KEEP THE RESEVOIR FULL.

Dec 09, 2015 | Cars & Trucks

1 Answer

How do you bleed rear brakes on a 1995 saturn


same as bleeding any brake system . 2 person operation. pump up the brake pedal and hold it down -undo the bleed screw until the pedal is on the floor. hold there until the bleed screw is tightened . repeat the process until no air comes out of the bleed screw. Always start at the longest line first and finish at the shortest. Keep an eye on the reservoir level during the process.

Aug 12, 2014 | Cars & Trucks

1 Answer

How do i bleed new brake caliper


Press brake, let off. Open bleed screw until the fluid runs out with no bubbles. Tighten bleed screw. Press brake and hold. Open bleed screw until pedal goes to floor then close bleed screw with pedal pressed to floor.. Fluid should come out with no air bubbles when open. If they are present repeat the last part.

Jan 16, 2011 | 1996 Lexus ES 300

2 Answers

PETAL GOING TO THE FLOOR REPLACED MASTERCYLINDER BUT STILL GOING TO THE FLOOR


Any time the internal pressurizable portion of the brake system is breached, i.e. bad seals, broken lines, replacing ABS or master cylindar or blown out cylindars at the wheel you must bleed all the air out of the system. A proper bleed requires 2 people. one person operates the bleed screws while the other holds the pedal down. The screw operator is in charge they tell the pedal operator when to push. the pedal must not be released until the bleed screw is closed again or it will **** air back into the line.

to bleed the system you top it off with fluid then
Open a single bleed screw. tell the person to press the pedal and hold it. the bleed screw will sputter with air and fluid forced out. close the screw and then tell the person in the vehicle to release the pedal. repeat this as many times as necessary to get a steady stream of fluid with no air out. close the screw and that line is done move to the next. The bleed screws are located in slightly different spots on different cars but they should all be somewhere near the caliper or cylinder on the back side of each wheel. Obviously you can trace the brake lines to them.

Jan 13, 2011 | 2003 Ford Taurus

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

For install of hydrolic clutch master cylinder, how do I bleed the line?


The slave cylinder on the transmission flywheel housing has a bleed screw. Fill the clutch reservoir on the master cylinder to 'max'. Have a friend depress the clutch pedal and keep it pressed. Open the bleed screw half a turn to release the air and then lightly re-tighten the bleed screw . Ask for the pedal to be released then depressed fully again and held there. Again release the bleed screw half a turn to release air bubbles. Keep repeating the above cycles until no more air is forthcoming and then tighten the bleed screw firmly. Your done

Dec 04, 2010 | 1987 Nissan Pathfinder

1 Answer

1987 Maxima-5 speed is difficult to grt in to gear--How to adjust clutch and check clutch hydraulic fluid?


TO ADJUST PEDAL HEIGHT ADJUST WITH A STOPPER LIMITING THE UPWARD TRAVEL OF THE PEDAL.PEDAL FREE PLAY IS ADJUSTED AT THE MASTERCYLINDER PUSH ROD.IF PUSH ROD IS NON ADJUSTABLE FREE PLAY IS ADJUSTED BY PLACING SHIMS BETWEEN THE MASTERCYLINDER AND THE FIREWALL.ON A FEW MODELS PEDAL FREE PLAY CAN ALSO BE ADJUSTED AT THE OPERATING SLAVE CYLINDER PUSHROD.PUSHRODS ARE AVAILABLE IN THREE LENGTHS FOR THE 310.PEDAL HEIGHT ABOVE FLOOR IS 6.73 - 7.13 INCH PEDAL FREE PLAY IS 0.04 - 0.12 INCH.YOU HAVE CLUTCH FLUID LONG AS YOU SEE BRAKE FLUID IN MASTERCYLINDER.IF MASTERCYLINDER LOW YOU HAVE TO BLEED THE THE CLUTCH MASTERCYLINDER BY LOCATING BLEED SCREW ON SLAVE CYLINDER. REMOVE THE BLEED SCREW DUST CAP.ATTACH A CLEAR TUBE TO THE BLEED SCREW.PUT OTHER END OF CLEAR TUBE IN A CLEAN CONTAINER OF BRAKE FLUID.FILL THE MASTERCYLINDER WITH BRAKE FLUID.OPEN BLEED SCREW 3/4 A TURN.DEPRESS CLUTCH PEDAL QUICKLY.HOLD IT DOWN.HAVE A HELPER TIGHTEN THE BLEED SCREW.ALLOW PEDAL TO RETURN SLOWLY.BLEEDER SCREW TORQUE IS 5 - 6 FT LBS.IF YOU SEE AIR BUBBLES CLEAR BLEED TUBE.REPEAT THE BLEED PROCESS UNTIL YOU SEE NO AIR BUBBLES.DONT LET CLUTCH MASTERCYLINDER GO DRY WHILE BLEEDING.IF SO YOU GOT START BLEEDING PROCESS ALL OVER.HOPE THIS HELP.

Aug 05, 2010 | 1987 Nissan Maxima

1 Answer

Clutch mastercilinder bleeding bmw 325tds how do you get brakefluid from reservoir to the slavecilinder. must it be pumped or will normal bleeding solve my problem


You can try regular bleeding by pumping pedal, also you can try a bleeding tool hooked to cylinder bleeder screw, and last a plastic bleeding siringe to push fluid through the bleeder screw into master, i would start with bleeding the master at the line first then go to the slave cylinder and if that doesnt work then try pushing fluid through bleeder screw into master.

Jul 19, 2010 | 1994 BMW 3 Series

1 Answer

I need to know what the coolant fill procedure is for my 2000 olds intrigue . i do not have an owners manual


What engine? For the 3.5l, jack up the right front. Remove the bleed screw that is in the upper right of the radiator. Fill the coolant recovery tank until the coolant flows out of the bleed screw. Put a paper towel or rag between the outlet on the side of the bleed screw and the headlight. Screw the bleed screw until it barely closes. Run the engine and open the bleed screw until coolant streams out of the outlet. Close and let engine warm till thermostat opens. Carefully crack open bleed screw very slightly and let air out - careful, this is killer hot steam and water. Check coolant level. Unjack car and recheck coolant level after 4 or 5 thermal cycles (cold start, warm til thermostat opens, cool down).

Mar 20, 2010 | 2000 Oldsmobile Intrigue

2 Answers

I cant not find the bleed screw or line for a 2000 jeep wrangler 6 cyl,its not where the book says is suppose to be


bleed screw or line for what?? Could you be alittle more specific?? It's hard to help you if you don't give a little more information than bleed screw and line. there are many bleed screws and lines on your Jeep.

Jul 24, 2008 | Jeep Wrangler Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22423 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...