Question about Peugeot 206

1 Answer

Peugeot 206cc central locking

The central locking on my Peugeot 206cc does not lock or unlock the doors or boot from the remote key buttons. The lights flash but locks don't work. The doors lock manually by key, but the bootlid does not Also the folding roof doesn't operate, maybe because the boot won't unlock ?. Any suggestions please.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Peugeot Expert
  • 215 Answers

Have you tried to disconnect battery terminal and wait for 5 minutes before connecting again to check the remote locking?

Posted on Jan 08, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: peugeot 406 central locking

you need to reprogram the fob

Posted on Oct 07, 2008

billtec
  • 63 Answers

SOURCE: Peugeot 406 estate, locking problem

HI,THIS IS VERY COMMOM ON ALL PUGS AND CITRONS,TRY GOOD OLD WD40 SPRAYING ON THE KEY AND KEEP WORKING KEY IN/OUT OF LOCK,IT WILL START TO TURN LOCK WHEN ALL THE WORKS ARE CLEAN,THANKS.

Posted on Jan 03, 2009

  • 93 Answers

SOURCE: peugeot 307 1.6 petrol central locking problem

leave ign off with key out 3mins disconnet battery 5 mins reconnett and press lock/ unlock repeatedly until locks cycle through to re sync try this any probs come back to me

Posted on Feb 23, 2009

  • 215 Answers

SOURCE: peugeot 307 hdi 2002 5 door will not start

Check the fob battery because if the battery has gone then you can't immobilise the car immobiliser which in turn doesn't let you start the engine however it cranking. open the bonnet and remove the clips of car battery for a good 15-20 minutes and put them back and check your remote key and try to start your car. If nothing happens then let your car diagnosed by a experienced mechanic who is able to read out the ecu codes.

Posted on Sep 04, 2009

  • 1 Answer

SOURCE: i need to reset my peugeot 406 key fob

Had same trouble with my 406, fixing no problem, with new battery in fob, insert into ignition, turn key, BUT DO NOT START ENGINE, hold button for about 10 seconds release button and remove key from ignition, then try and see if doors lock on remote, if not try again, had to do this a couple of times, and it worked, sorry to say that now my key fob button has completely fell apart, through ware and tare

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my Peugeot 307 lock and unlock itself repeatedly?


Probably a lock is not latching properly. Try servicing the locking mechanisms.

Sep 21, 2018 | Peugeot Cars & Trucks

1 Answer

Peugeot 307 Hdi 2004 intermittently locking/unlocking via central locking & interior light flashing??


I suggest you get one of those manuals people get nowadays to
do it yourself.. My brother use it to repair my car and it's totally repaired now. he got it from. www.reliable-store.com

Mar 06, 2018 | Peugeot 307 Cars & Trucks

1 Answer

How do i reset central locking on a micra 04 reg


Try the following:

"KEY FOB PROGRAMMING
NISSAN
SYSTEM DESCRIPTION
The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and hazard reminder. When the doors are locked and
unlocked the unit flashes the hazard lights once for lock and twice for unlock.
A maximum of four remote controls are allowed to be programmed.
ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II
Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.
Procedure
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key?s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key?s for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds."

Mar 12, 2012 | Nissan Cars & Trucks

2 Answers

My bmw 320d remote wont lock car however does lock the car with the key its a 55 reg


1
Programming
When
Key batteries completely discharged. Key batteries not replaced within 60 seconds. Key added or replaced. DO NOT press remote control buttons during battery replacement.
How
Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button Fig. 1 [1]. Press lock button Fig. 1 [2] briefly 3 times within 10 seconds keeping unlock button [1] depressed. Release unlock button Fig. 1 [1]. Some models: LED Fig. 1 [3] flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Some models: Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously
Later keys with bmw badge on key. Battery can not be replaced
Battery in key charges while driving

Dec 22, 2010 | BMW 3 Series Cars & Trucks

2 Answers

2002 bmw 530i key does not (remotely) unlock doors or trunk but they work fine manually.


Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button. Press lock button briefly 3 times within 10 seconds keeping unlock button depressed. Release unlock button. Some models: LED flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously.

Mar 09, 2010 | 2002 BMW 5 Series

1 Answer

My key does not open or lock my doors remotely had key checked and is sending a signal but still not working


You do not say what year your car is, here is standard programming for most bmw,s,after battery or key replacement or malfunction.
Unlock car,enter, make sure all doors boot etc are closed.
Switch ignition on and off,remove key.
PRESS AND HOLD unlock button.
Press lock button 3 times in 10 seconds
Release unlock button
Some models led flashes in key for 10 seconds
Later keys central locking will lock unlock rapidly to confirm reset.
Later keys without led has no battery replacement,as it charges as you drive.So if you have this type charge before reprogramming

Dec 22, 2009 | BMW 3 Series Cars & Trucks

1 Answer

Central Locking does not work


You must reset your remote control in order for the lock/unlock to work properly.

To reset remote you would:
1)Insert Key in Ignition Turn to Position 1(Don't Start the Engine) for about 5 seconds
2)Turn Key Off and HOLD the LOCK button on Remote while pressing the UNLOCK 3 TIMES
3)Release both lock and unlock buttons you are holding
4)All doors should automatically unlock

And exit the door and lock with the Remote.

Sep 19, 2009 | 2000 BMW 3 Series

3 Answers

I need to reset my peugeot 406 key fob


Had same trouble with my 406, fixing no problem, with new battery in fob, insert into ignition, turn key, BUT DO NOT START ENGINE, hold button for about 10 seconds release button and remove key from ignition, then try and see if doors lock on remote, if not try again, had to do this a couple of times, and it worked, sorry to say that now my key fob button has completely fell apart, through ware and tare

May 19, 2009 | 2005 Peugeot 405

3 Answers

Peugeot 307 1.6 petrol central locking problem


leave ign off with key out 3mins disconnet battery 5 mins reconnett and press lock/ unlock repeatedly until locks cycle through to re sync try this any probs come back to me

Dec 25, 2008 | 2005 Peugeot 405

3 Answers

Key fob not working


hello mate.. if it has stopped working you might want to check the battery first.. if you are sure that the battery is fine then consider reprogramming the fob to your car.. here are the steps to follow.. NISSAN

Remote Control Fob Procedures:

The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and emergency hazard reminders.

When the doors are locked and unlocked the unit flashes the hazard lights once for lock and twice for unlock.

A maximum of four remote controls are allowed to be programmed:

ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II

Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.

Procedure:
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Next, turn ignition switch to OFF position. Leave key in ignition switch.
3. Wait 2 seconds then the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds.


http://www.autokeysquad.com/nissan-fob-programming



i hope this can help you.. :)

Jul 28, 2008 | 2005 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85161 Answers

scj103

Level 2 Expert

89 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...