Question about 2008 Mercedes-Benz Mercedes Benz E Class

Open Question

Where is Engine shutoff solenoid location in 2008 MB E350 4MATIC

Car used to start at times and now it does not. I get a DTC PO106

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Trailblazer, 4.2 I6, code P1345, voltage does not change to cam position actuator 12+ volts all the time?


If this DTC sets, there is a problem with the camshaft position actuator solenoid high control circuit shorted to voltage or the solenoid stuck open.
The PCM sends a pulse width modulated 12 volt signal to a (CMP) actuator solenoid in order to control the amount of engine oil flow to a cam phaser passage.
Do you know what a pulse width modulated signal is ?
Diagnostic Aids
Important: Scan tool control of the CMP actuator solenoid is inhibited when DTC P1345 sets.
The following conditions may cause this DTC to set:
• An improperly torqued harmonic balancer
• A mis-built or mis-timed engine
• A loose or missing crank damper bolt
• The camphaser solenoid stuck open
• The camphaser stuck in a position other than 0 degrees
• The camphaser does not return to 0 degrees within 16 seconds

Do you know what a diagnostic flow chart is ?

If this DTC sets, there is a problem with the camshaft position actuator solenoid high control circuit shorted to voltage or the solenoid stuck open.
Step
Action
Values
Yes
No
1
Did you perform the Diagnostic System Check-Engine Controls?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check - Engine Controls
2
Start the engine.
Clear the DTCs with a scan tool.
Does the scan tool indicate that DTC P0014 failed this ignition?
--
YES - Go to DTC P0014
NO - Go to Step 3
3
Observe the Freeze Frame/Failure Records for this DTC.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
--
YES - Go to Step 4
NO - Go to Diagnostic Aids
4
Turn OFF the ignition.
Inspect the crank damper bolt for the proper torque. Refer to Crankshaft Balancer Replacement in Engine Mechanical.
Did you find and correct the condition?
YES - Go to Step 9
NO - Go to Step 5
5
Disconnect the camshaft position actuator.
Remove the camshaft position (CMP) actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Replacement .
Jumper the camshaft position solenoid actuator high control circuit of the actuator solenoid assembly to 12 volts. Refer to Using Connector Test Adapters Wiring Systems.
Jumper the low reference circuit of the camshaft position actuator solenoid to a good ground. Refer to Using Connector Test Adapters in Wiring Systems.
Does the pintle inside the CMP actuator solenoid move?
YES - Go to Step 6
NO - Go to Step 8
6
Inspect the CMP actuator for binding or being stuck. Refer to Camshaft Position Actuator Diagnosis in Engine Mechanical.
Did you find and correct the condition?
--
YES - Go to Step 9
NO - Go to Step 7
7
Inspect the engine for correct valve timing. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical.
Did you find and correct the condition?
--
YES - Go to Step 9
NO - Go to Diagnostic Aids
8
Replace the camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Replacement .
Did you complete the replacement?
--
Go to Step 9
--
9
Clear the DTCs with a scan tool.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
--
Go to Step 2
Go to Step 10
10
Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?
--
Go to Diagnostic Trouble Code (DTC) List
System OK

May 07, 2017 | Cars & Trucks

1 Answer

How to change a csmshsft sensor on a 2008 cadillac srx


Before you replace a part you may or may not need . Why ? What code ? Does the vehicle run ? There has been a lot of confusion on these vehicles with variable valve timing , mixing up cam sensors with camshaft actuators
DTC P0008: Engine Position System Performance Bank 1

DTC P0009: Engine Position System Performance Bank 2
The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).


?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.



DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2

DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .

Jul 24, 2016 | 2008 Cadillac Srx

1 Answer

Where is cam shaft sensor located on a 08 saturn aura


Which engine ? This vehicle had option of six different engines , 2.4 , 3.5 , 2.8 , 3.0 , 3.2 , 3.6 And are you picking on the right part ? What code > DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit
It may not even be a cam sensor problem !
DTC P0340: Intake CMP Sensor Circuit

DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance
Camshaft Position (CMP) Actuator System
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the Park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the Park position, and the locking pin retains the CMP actuator sprocket to the camshaft


It may

Jul 06, 2016 | 2008 Saturn Aura

1 Answer

Where is the fuel system shutoff for a 2008 suzuiki forenza sedan 2.0 I replaced the head gasket and opened the trunk without the key and it beeped at me and flashed lights then shut my fuel pump off


is this car fitted with an immobilizer?
if yes the operators guide tells you ever step here.
the PCM decides to run the pump. not you.
immo happy
spark good
crank engine, do you have full fuel pressure cranking, yes, no.?
if no pressure cranking any scan tool will tell you WHY its cutting fuel.
called DTC errors.

Sep 26, 2014 | 2008 Suzuki Forenza

1 Answer

Runs good for a while then shuts off acts like it is running hot at times but when i check it is not hot rebuilt engine new radiator water pump thermostat also at times act like it is not getting gas but...


In the early 80s they incorporated a shutoff solenoid in the event of overheating. What happens is when the engine reaches a critical level it then opens a vacuum solenoid forcing the engine to stall to prevent it causing extreme damage. I am not sure its location on your vehicle but when it happens again, try clamping off some vacuum lines on the solenoids to find out which one clamped will the car start. hope this takes care of things. ps...change your fuel filter, It may be restricting your fuel.

Oct 19, 2013 | 1989 Ford F 150

1 Answer

Fault code P0021


Hi there:P0021 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

A code P0021 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0021 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft. A P0021 engine code is basically the same as a P0011 code, except this is for Bank 2, not Bank 1.

Most likely a P0021 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.


A P0021 DTC trouble code may be caused by one or more of the following:Incorrect camshaft timingWiring problems (harness/wiring) in intake timing control valve control solenoid systemContinuous oil flow to VCT piston chamberFailed timing valve control solenoid (stuck open)

Possible Solutions:This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.To reset the fuel pump, press the button on the switch. The switch is located immediately below the hole in the trunk side trim.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa.

Mar 06, 2012 | Cars & Trucks

1 Answer

P0012


P0012 - "A" Camshaft Position - Timing Over-******** (Bank 1)
OBD-II DTC Trouble Code Description

"A" Camshaft Position - Timing Over-******** (Bank 1)
What does that mean?

A code P0012 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0012 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-********, the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.
Potential Symptoms

Most likely a P0012 DTC will result in one of the following:

hard starting
poor idle and/or
stalling

There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.
Causes

A P0012 DTC trouble code may be caused by one or more of the following:

Incorrect camshaft timing
Wiring problems (harness/wiring) in intake timing control valve control solenoid system
Continuous oil flow to VCT piston chamber
Failed timing valve control solenoid (stuck open)

Possible Solutions

The main thing to check is to verify the operation of the VCT solenoid. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Nov 26, 2011 | 2004 Ford F150

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on


O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction
--------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Jul 07, 2011 | 1995 Toyota Camry

1 Answer

EL VEHICULO TIENE PERDIDA DE POTENCIA Y EN EL SCANNER MUESTRA LOS CODIGO PO0011; PO0012


P0011 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
A code P0011 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.

Potential Symptoms: Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

Causes: A P0011 DTC trouble code may be caused by one or more of the following:
Incorrect camshaft timing
Wiring problems (harness/wiring) in intake timing control valve control solenoid system
Continuous oil flow to VCT piston chamber
Failed timing valve control solenoid (stuck open)

Possible Solutions: This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.


P0012 - "A" Camshaft Position - Timing Over-Retarded (Bank 1)
A code P0012 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0012 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.

Potential Symptoms: Most likely a P0012 DTC will result in one of the following:
hard starting
poor idle and/or
stalling

There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.
A code P0012 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0012 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.

Causes: A P0012 DTC trouble code may be caused by one or more of the following:
Incorrect camshaft timing
Wiring problems (harness/wiring) in intake timing control valve control solenoid system
Continuous oil flow to VCT piston chamber
Failed timing valve control solenoid (stuck open)

Possible Solutions:
The main thing to check is to verify the operation of the VCT solenoid. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Hope this helps. Suerte.

May 30, 2011 | Toyota Yaris Cars & Trucks

1 Answer

Code po410


DTC P0410 Secondary Air Injection (AIR) System

Circuit Description
The PCM activates the secondary air injection system by grounding the AIR relay. This energizes the pump and the vacuum control solenoid. As vacuum is applied to the two shutoff valves, fresh air is allowed to pass through them. The AIR pump forces fresh air past the shutoff valves and into the exhaust stream in order to accelerate catalyst operation. The PCM will run up to 3 diagnostic tests using the O2S1 voltage and Short Term FT to verify system operation. The system can be diagnosed during normal secondary air injection operation or the scan tool can activate the system specifically for diagnostic purposes. If an air flow problem is detected this DTC will set. When inactive, the shutoff valve prevents air flow in either direction.

Conditions for Running the DTC
• AIR system commanded ON for more than 20 seconds.

• The IAT is between 1° C and 151° C (32° F and 302° F).

• The ECT is between 5° C and 114° C ( 41° F and 230° F).

• Battery voltage is more than 11.7 volts.

• Engine run time is more than 200 seconds.

• Calculated air flow is more than 11 gps.

• Accumulated flow between 240 cts and 600 cts.

• BLM cell of 16 or 17.

• TPS changes less than 5 percent.

• Stabilization time of more than 1 second.

• Fuel ethanol composition of less than 15 percent.

• DTCs 105, 107, 108, 112, 113, 117, 118, 122, 123, 130, 131, 132, 133, 1133, 134, 171, 172, 178, 179, 201, 202, 203, 204, 300, 336, 340, 341, 506, 507, 601, 602, and 1621 are not set.
Conditions for Setting the DTC
Lean time is more than 1 second during 4 second active test.

Action Taken When the DTC Sets
• The malfunction indicator lamp (MIL) illuminates after two ignition cycles with the malfunction present.

• The PCM records the operating conditions at the time the diagnostic fails. The Freeze Frame and Failure Records buffers stores this information.

• A history DTC is stored.

Conditions for Clearing the MIL/DTC
• The MIL will turn OFF after 3 consecutive ignition cycles in which the diagnostic runs without a fault.

• A history DTC will clear after 40 consecutive warm up cycles without a fault.

• A scan tool can clear the DTCs.


Diagnostic Aids
An intermittent may be caused by any of the following conditions:

• A poor connection

• Rubbed through wire insulation

• A broken wire inside the insulation

Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.

Test Description
The numbers below refer to the step numbers on the diagnostic table.

This step checks for a restriction in the engine vacuum supply to the AIR shutoff valve.

This step determines if the lack of air is caused by an open in the AIR supply hose or a defective shutoff valve.

Mar 17, 2011 | 2000 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...