Question about 2014 Dodge Dart

1 Answer

Location third brake light wires

Just installed a rear spoiler on a 2014 dodge dart,I am looking for a harness to wire in third brake light on spoiler....can i wire it in inside trunk or do i have to go to the existing third brake light on car that is above the back glass

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 71 Answers

You can use one of the wires from either brake light and make yourself a good ground in trunk and running the two wires to you light switch. be careful where and how you run wires around the trunk hindges as you do not want them to become pinched and short out as that is a safety issue and get you pulled over. always solder and heat shrink all splices and wire to wire connections, if you dont you will hate your self later as wire from front of car to back of car could then need to be replaced.

I’m happy to assist further over the phone at https://www.6ya.com/expert/christpher_f760d0f18f8eedc3

Posted on Sep 12, 2014

  • Ronald Tworek
    Ronald Tworek Feb 01, 2015

    BLINKS, with turn signal! Need to locate Third Light Wire!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to hardwire my stereo in my car need to know what each wire is by color. Can anyobe help with that don't feel like paying 150 for a harness. 2014 dodge dart se Install new double din.


As far as the size goes I have n0o idea, but if you would like to do this install correctly and have the car start after install (it is hooked into the security system) contact www.crutchfield.com

Oct 11, 2018 | Dodge Cars & Trucks

1 Answer

Installing a spoiler on a 90 accord but dont know wat wires to splice into for brake light on the spoiler. obviously the brake lights but what wires are wat in the harness


The power wire that you are looking for is green with white tracer and the ground wire is Black.

Use a test light to confirm it powers with the brake before you hook it up

Aug 17, 2013 | 1990 Honda Accord

1 Answer

Third eye brake light won't work and the buld is new. I've tried location the fuse and can't find on specifically for that, would it be tied to something else?


all of the brake lights are on the same fuse. If the other brake lights are working than the fuse is good.

If I remember correctly this third brake light is located in the trunk lid. I would suspect that there is a broken power or ground wire going to the socket for the bulb. The usually area for this to happen is where the wiring harness flexes when the trunk is opened and closed. I think the connector for the harness is in the same area and I'm pretty sure it is on the drivers side. Take a peak at the wiring in that area. you may have to remove some tape to get a good look. If there are wires broken than a simple repair should get it working again.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Sep 30, 2011 | 1998 Dodge Neon

1 Answer

My rear spoiler lights will not come on when i press on the brakes?


There can be a faulty connection or break of the wire that goes to the light. This can be in the boot hinges harness as it can get damaged in this section.
If the tail brake lamps are workingg then the fault is only in this section as it is normally coupled to the tail brake circuit .So remove the lights and trace the wire down the harness to find the open wire.

Sep 06, 2011 | 2006 Nissan Altima

2 Answers

2007 dodge caliber brake lights dont work, bulbs are good, hatch back brake light works any ideas what this could be. derek


Check the connections on the "body harness" that is located near the hinge for the decklid.this harness,if i remember correctly,is on the driver-side of the car.Also check to make that no wire has any "bare spots"that are grounding to any metal.

Feb 12, 2011 | Dodge Caliber Cars & Trucks

2 Answers

I have a 2000 Dodge RAM 3500 with no lower brake lights. The turn signals work and the hazard lights work so the bulbs are good. The center high mounted stop lamp works but just in case I replaced the...


if the third brake light works then ther is a broken wire. start looking for it at the tail lights and work forward if you cant find the break you can always run a new possitive wire from either the third brake light to the tail lights or if the trailer wiring harness hase power to the brake lights you can splice in there as well. hope this helps

Mar 14, 2010 | 1994 Dodge Ram

1 Answer

How to replace 3rd brake light on 2004 Chrysler Pacifica?


the 3rd brake light is mounted to the spoiler. you need to remove the spoiler from the liftgate to acces the mounting bolts and the wire clip. there are five points of attachment of the spoiler,four hex nuts (metric) and one snap clip. two are accessable when the liftgate is open, they are in the corners of the liftgate. two more are under the upper rear window interior trim. the interior trim is held on by snap clips. if you pry outward on the trim starting on the right side of the window and work your way toward the middle you will be able to gain access to the two other nuts. once you have removed all four nuts, then close the liftgate and remove the spoiler by lifting up to disengage the last attachment point (snap clip). you will then need to change the light by removing the two nuts and disconnecting the wire clip. re-instal is the opposite of above. make sure that the wire for the third brake light does not get pinched when installed. (mine was improperly installed from the factory and the wire was pinched and this may have been why there was an early failure of the light)

Feb 18, 2010 | 2004 Chrysler Pacifica

1 Answer

2005 Lincoln Ls 3rd Brake Light Wiring


The best way to wire a third brake light is to run the wire directly from the brake light switch on the side of the steering colum to the light. You will need a test light to find out what wire lights up when you push the brake pedal. Then you can splice into it when you run your wire to the rear light.

Jan 01, 2009 | Lincoln LS Cars & Trucks

Not finding what you are looking for?
2014 Dodge Dart Logo

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...