Question about Ford Cars & Trucks

1 Answer

Where is the slave cylinder located on a 1982 Ford F 150 with a straight in line v6

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 588 Answers

I believe you are looking for a master cylinder. A slave cylinder would be on the wheel if talking brakes. If talking clutch, a slave cylinder would be on the bell/flywheel housing between the motor and tranny. The master cylinders for either brakes or clutch would be on the firewall under the hood directly in front of the drivers side.

Posted on Oct 12, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch goes straight to the floor


The usual problem is the slave cylinder.

Apr 20, 2014 | 1997 Ford F150 Regular Cab

1 Answer

Where is the bleedwer screw located on a 2000 ford f 150 for the slave cylinder


it is located at the highest point of the cylinder at the end. normally around where the hose is bolted on

Jan 13, 2014 | Ford Club Cars & Trucks

1 Answer

96 ford 4.9 5 speed hydrolich clutch wont shift all of a sudden new master cylinder


You have a leak and you have air in the system. More than likely the slave cylinder is leaking, the slave is a direct acting one and as with all direct acting slave cylinder it is located inside the transmission bell housing on the transmission input shaft collar. The transmission must be removed to replace it.

Jun 23, 2012 | Ford F150 Cars & Trucks

1 Answer

1982 ford f150 351 firing order diagram...


Hi, the firing order is ( 1 - 3 - 7 - 2 - 6 - 5 - 4 - 8 )

The distributor rotor turns COUNTERCLOCKWISE
The marked # 1 position on the distributor cap faces to the REAR and slightly towards the drivers side, the engine cylinders spark plug locations are numbered.


hfmiles_7.jpg


The wiring diagram....

Jul 11, 2011 | 1982 Ford F 150

2 Answers

I need the correct firing order diagram for a 1982 ford f150 351 windsor please help at least a link to a site



The firing order is ( 1 - 3 - 7 - 2 - 6 - 5 - 4 - 8 )

The distributor rotor turns COUNTERCLOCKWISE

The marked # 1 position on the distrubutor cap faces to the REAR and slightly towards the drivers side

The engine cylinders / spark plug locations are numbered :


firewall

4 - 8

3 - 7

2 - 6

1 - 5

front

If someone has altered the disstributer, pull #1 plug, put finger over hole, turn engine over until compression on that cyl, line up timing marks (ball park only) and rotor will be pointing at the correct terminal for #1 cylinder plug wire connection, in the cap.

Feb 26, 2011 | 1982 Ford F 150

1 Answer

Location of slave cylinder


I THINK ALL OF THE FORDS HAVE INTERNAL SLAVE CYLINDERS.WHERE I WORK (PROVEN FORCE/CLUTCH AND U-JOINT) WE USUALLY SUGGEST CHANGING WHEN YOU DO THE CLUTCH,BECAUSE IT IS INTERNAL.THEY TEND TO FAIL A LOT IN COLDER WEATHER ALSO

Oct 10, 2010 | 1982 Ford F 250

1 Answer

How do you remove the hose on a slave cylinder for a 96 ford ranger


There is a special tool to push the white collar down to remove the line from the clutch slave cylinder. Most clutch kits come with this tool but it is easily available from most parts stores. If you have the tool, lubricate the sleeve and push the line into the slave cylinder to release the holding fingers, then push on the sleeve with the tool and pull straight out on the line to remove. Sometimes they can be a pain. another solution is remove the whole line up to the master cylinder with it, you just have to route it accordingly. I have done this with some that wont disconnect.

Aug 19, 2010 | 1996 Ford Ranger SuperCab

1 Answer

I have a 1996 ford f-150 and my clutch just sticks to the floor. It doesnt retract.


Check the clutch fluid, under the hood on the firewall, if the fluid is low then you need to inspect the for a leak. This could be a leaking slave cylinder which is located internal of the trans bellhousing, if you see any dampness this would indicate a slave cylinder leak. Replacement of the slave , line , and the master cylinder will be required. The slave and master have been updated and require all three to be replaced. Thankyou ,Please rate this answer This will help me out .

May 30, 2010 | 1996 Ford F150 Regular Cab

1 Answer

Brake porportion valve on 1982 ford F-150 moved off of center. How to adjust


If you are certain your valve is the problem, then you need to replace it, you can't adjust it. You should make sure your calipers and drums are correctly functioning. Make sure your master cylinder is functioning correctly, as well as making sure that your brake lines are not stopped up or leaking. Replacing the proportion block is one of the hardest things you'll ever have to replace on a brake system. The bolts will be rusted.

Jan 26, 2010 | 1982 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...