Question about 1999 Peugeot 206

1 Answer

Where is the camshaft and crankshaft located on the engine

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Peugeot Master
  • 3,961 Answers

That model was sold with a choice of 3 engines. On all the crankshaft is located at the bottom of the engine, above the sump, and the camshaft at the top of the engine under the cam cover.
.

Posted on Dec 09, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 silverado EGR location on a 5.3 fuel injected v8


Doesn't have a EGR valve ! Has Camshaft Actuator System .
Camshaft Actuator System Description
The camshaft position (CMP) actuator system is used for a variety of engine performance enhancements. These enhancements include lower emission output through exhaust gas recirculation (EGR) control, a wider engine torque range, improved gas mileage, and improved engine idle stability. The CMP actuator system accomplishes this by controlling the amount of intake and exhaust valve overlap. For the 6.0 liter (LY6, L76) and the 6.2 liter (L92) engine, the Park position for the CMP actuator and camshaft is 8.5 degrees before top dead center (BTDC) or 17 crankshaft degrees BTDC. The engine control module (ECM) can only command the CMP actuator to retard the valve timing from the Park position or advance the valve timing back to the Park position. The total range of valve timing authority is 31 degrees camshaft rotation, or 62 degrees of crankshaft rotation. The control range is from the Park position of 8.5 degrees camshaft or 17 degrees crankshaft BTDC, to 22.5 degrees camshaft or 45 degrees crankshaft after top dead center (ATDC).

May 31, 2017 | Cars & Trucks

1 Answer

Need to know the location of both crankshaft position sensor on 2008 Chevrolet hhr plz thx


Only has one crankshaft position sensor ,an cam sensors . To change the crank sensor u would have to pull the starter ,located above starter .
Camshaft Position Sensor Replacement - Intake Camshaft Position Sensor Replacement - Exhaust
After a crank sensor replacement a
Crankshaft Position System Variation Learn has to be done !
Important: The crankshaft position (CKP) system variation learn procedure is required when the following service procedures have been performed, regardless of whether DTC P0315 is set:
?€¢
Engine replacement


?€¢
Engine control module (ECM) replacement


?€¢
Crankshaft damper replacement


?€¢
Crankshaft replacement


?€¢
CKP sensor replacement


?€¢
Any engine repairs which disturb the crankshaft to CKP sensor relationship

Important: The scan tool monitors certain component signals to determine if all the conditions are met to continue with the CKP system variation learn procedure. The scan tool only displays the condition that inhibits the procedure. The scan tool monitors the following components:
?€¢
CKP sensor activity--If there is a CKP sensor condition, refer to the applicable DTC that set.


?€¢
Camshaft position (CMP) signal activity--If there is a CMP signal condition, refer to the applicable DTC that set.


?€¢
Engine coolant temperature (ECT)--If the engine coolant temperature is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.

Apr 04, 2016 | Chevrolet Cars & Trucks

1 Answer

Timing set


Chain

Print


REMOVAL & INSTALLATION

4.3L, 5.0L, 5.7L and 7.4L Engines
See Figures 1, 2, 3, 4, 5 and 6

  1. Remove the timing cover. This will allow access to the timing chain.
  2. Crank the engine until the timing marks on both sprockets are nearest each other and in line between the shaft centers.



0996b43f80219aca.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Crank the engine until the timing marks on both sprockets are in line

  1. On 1996-98 vehicles remove the crankshaft position sensor reluctor ring, if equipped. On 7.4L engines tool J-41371 or its equivalent puller must be used to remove the reluctor ring.
  2. Take out the bolts that hold the camshaft gear to the camshaft. This gear is a light press fit on the camshaft and will come off easily. It is located by a dowel. The chain comes off with the camshaft gear.



0996b43f80219acb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Remove the camshaft gear retaining bolts


0996b43f80219acc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the camshaft gear and timing chain
A gear puller will be required to remove the crankshaft gear.
To install:

  1. Without disturbing the position of the engine, mount the new crankshaft gear on the shaft, and mount the chain over the camshaft gear. Arrange the camshaft gear in such a way that the timing marks will line up between the shaft centers and the camshaft locating dowel will enter the dowel hole in the cam sprocket.
  2. Place the cam sprocket, with its chain mounted over it, in position on the front of the truck and pull up with the three bolts that hold it to the camshaft.
  3. After the gears are in place, turn the engine two full revolutions to make certain that the timing marks are in correct alignment between the shaft centers. Tighten the camshaft sprocket bolts (and nut on the 4.3L) to 21 ft. lbs. (28 Nm) on 1988-95 models. On 1996-98 models, tighten the bolts to 18 ft. Lbs. (25 Nm). On the 7.4L, tighten them to 20 ft. lbs. (26 Nm) on 1988-95 models. On 1996-98 models, tighten the bolts to 25 ft. Lbs. (34 Nm).

When installing the crankshaft position sensor you must use install a new oil ring seal onto the sensor.
  1. Install the crankshaft position sensor reluctor ring (if equipped), onto the crankshaft until it is firmly seated against the crankshaft sprocket. On 1996-98 7.4L vehicles replace the reluctor ring with a new component.
  2. Install the front cover, torsional damper, water pump and the radiator.



0996b43f80219acd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: A gear puller will be required to remove the crankshaft gear


0996b43f8020d5d9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Timing mark alignment-4.3L, 5.0L, 5.7L and 7.4L engines

Apr 20, 2013 | 1993 Chevrolet Suburban

1 Answer

1977 ford pinto timming marks


Hope this helps. Please don't forget to rate....thanks!



c17hydro_169.gif

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)


On 2000 cc engines, turn the crankshaft until the two round locating holes in the camshaft pulley are visible from the rear side of the pulley, looking forward from the left-side of the car. When these two holes are parallel to the ground, the timing pointer on the crankshaft pulley should point to TDC. If the drive belt is dislocated, the crankshaft damper will be retarded or advanced 19° per cog on the belt.

If the engine you are working on does not have the two locating holes on the rear side of the camshaft pulley, then you will have to remove the drive belt cover and observe that when the crankshaft timing marks are aligned to TDC of the compression stroke of the No. 1 cylinder, the distributor rotor is pointing to the index mark on the upper lip of the distributor housing which coincides with No. 1 spark plug tower, and the pointer on the camshaft pulley is aligned with the index mark on the cylinder head.

On 2300 cc engines, there is an access plug provided in the cam drive belt cover so that the camshaft timing can be checked without removing the drive belt cover. Remove the access plug, turn the crankshaft until the timing mark on the crankshaft damper indicates TDC, and observe that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover. Also, the rotor of the distributor must align with the No. 1 cylinder firing position.


CAUTION:

After any procedure requiring removal of the rocker arms on the 2300, each lash adjuster must be fully collapsed after assembly, then released. This must be done before the camshaft is turned.



Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)
c17hydro_170.gif

Checking 2000 cc overhead camshaft timing (© Ford Motor Co)

May 08, 2011 | Ford Mustang Cars & Trucks

1 Answer

Need to know what the timing marks and locations for replacing the timing belt


Timing Belt Removal & Installation 3.0L Engine To Remove:
Exploded view of the timing belt and sprocket assembly (3.0L engine) 86723255.gif

  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts. Remove the engine mount insulator from the engine support bracket.
  3. Remove the engine support bracket. Remove the crankshaft pulleys and torsional damper. Remove the timing belt covers.
  4. Rotate the crankshaft until the sprocket timing marks are aligned. The crankshaft sprocket timing mark should align with the oil pump timing mark. The rear camshaft sprocket timing mark should align with the generator bracket timing mark and the front camshaft sprocket timing mark should align with the inner timing belt cover timing mark.
  5. If the belt is to be reused, mark the direction of rotation on the belt for installation reference. Mark the direction of travel for the timing belt for correct installation 86723p72.jpg
  6. Loosen the timing belt tensioner bolt and remove the timing belt.
  7. If necessary, remove the timing belt tensioner. Turn the center tensioner pulley bolt until the timing belt has enough slack . . . 86723p73.jpg
    . . . then slide the timing belt off of the camshaft sprockets 86723p74.jpg
  8. Remove the crankshaft sprocket flange shield and crankshaft sprocket.
  9. Hold the camshaft sprocket using spanner tool MB990775 or equivalent, and remove the camshaft sprocket bolt and washer. Remove the camshaft sprocket.
To Install:
  1. Install the camshaft sprocket on the camshaft with the retaining bolt and washer. Hold the camshaft sprocket using spanner tool MB990775 or equivalent, and tighten the bolt to 70 ft. lbs. (95 Nm).
  2. Install the crankshaft sprocket.
  3. If removed, install the timing belt tensioner and tensioner spring. Hook the spring upper end to the water pump pin and the lower end to the tensioner bracket with the hook out.
  4. Turn the timing belt tensioner counterclockwise full travel in the adjustment slot and tighten the bolt to temporarily hold it in this position.
  5. Rotate the crankshaft sprocket until its timing mark is aligned with the oil pump timing mark.
  6. Rotate the rear camshaft sprocket until its timing mark is aligned with the timing mark on the generator bracket.
  7. Rotate the front (radiator side) camshaft sprocket until its mark is aligned with the timing mark on the inner timing belt cover.
  8. Install the timing belt on the crankshaft sprocket while keeping the belt tight on the tension side. NOTE: If the original belt is being reused, be sure to install it in the same rotational direction.
  9. Position the timing belt over the front camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the rear camshaft sprocket and finally over the tensioner. CAUTION
    If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.
    Rent or borrow the special tool to hold the camshaft sprockets steady . . . 86723p75.jpg
    . . . while loosening the center retaining bolt on the camshaft pulley, then . . . 86723p76.jpg
    . . . remove the camshaft sprocket from the end of the camshaft 86723p77.jpg
    Timing belt tensioner and spring positions 86723254.gif
    Timing belt routing and timing mark locations 86723256.gif

  10. Apply rotating force in the opposite direction to the front camshaft sprocket (radiator side) to create tension on the timing belt tension side. Check that all timing marks are aligned.
  11. Install the crankshaft sprocket flange.
  12. Loosen the tensioner bolt and allow the tensioner spring to tension the belt.
  13. Rotate the crankshaft two full turns in a clockwise direction. Turn the crankshaft smoothly and in a clockwise direction only.
  14. Again line up the timing marks. If all marks are aligned, tighten the tensioner bolt to 250 in. lbs. (28 Nm). Otherwise repeat the installation procedure.
  15. Install the timing belt covers. Install the engine support bracket. Tighten the support bracket mounting bolts to 35 ft. lbs. (47 Nm).
  16. Install the engine mount insulator, torsional damper and crankshaft pulleys. Tighten the crankshaft pulley bolt to 112 ft. lbs. (151 Nm).
  17. Install the accessory drive belts.
  18. Reconnect the negative battery cable.
  19. Run the engine and check for proper operation.
prev.gif next.gif

Aug 17, 2010 | 1997 Dodge Caravan

1 Answer

How do I time a 2006 dodge caravan 2.4L


2.4L Engine
NOTE You may need DRB scan tool to perform the crankshaft and camshaft relearn alignment procedure.
  1. Remove or disconnect the following:
    • Negative battery cable
    • Right front wheel and inner splash shield
    • Accessory drive belts
    • Crankshaft damper
    • A/C compressor/alternator tensioner and pulley assembly
    • Lower front timing cover
    • Upper front timing cover
    • Right engine mount
    • Engine mount bracket

    NOTE This is an interference engine. Do not rotate the crankshaft or the camshafts after the timing belt has been removed. Damage to the valve components may occur. Before removing the timing belt, always align the timing marks.
  2. Rotate the crankshaft until the Top Dead Center (TDC) mark on the oil pump housing aligns with the TDC mark on the camshaft sprocket (located on the trailing edge of the tooth).
  3. Loosen the timing belt tensioner lock bolt.
  4. Insert a 6mm Allen wrench into the hexagon opening located on the top plate of the belt tensioner pulley. Rotate the top plate clockwise until there is enough slack to remove the belt.
  5. If necessary, remove the camshaft timing belt sprockets.
  6. If necessary, remove the crankshaft timing belt sprocket using removal tool No. 6793, or equivalent.
  7. Place the tensioner into a soft-jawed vise to compress the tensioner.
  8. After compressing the tensioner, insert a pin (a 5/64 in. Allen wrench will also work) into the plunger side hole to retain the plunger until installation.

09943d3.gif

Camshaft and crankshaft alignment marks—2.4L engine


ed2b9ee.gif

To lock the timing belt tensioner, be sure to fully insert the smaller Allen wrench into the tensioner as shown—2.4L engine



03f364a.gif

Installation of the timing belt, notice the camshaft alignment— 2.4L (VIN B) engine


To install:
  1. If necessary, use tool No. 6792, or equivalent, to install the crankshaft timing belt sprocket onto the crankshaft.
  2. If necessary, install the camshaft sprockets onto the camshafts. Install and tighten the camshaft sprocket bolts to 75 ft. lbs. (101 Nm).
  3. Set the crankshaft sprocket to Top Dead Center (TDC) by aligning the notch on the sprocket with the arrow on the oil pump housing.
  4. Set the camshafts timing marks so the exhaust camshaft is 1/2 notch below intake camshaft sprocket. Make sure the arrows on both camshaft sprockets are facing up
  5. Install the timing belt starting at the crankshaft, then around the water pump sprocket, idler pulley, camshaft sprockets and around the tensioner pulley.
  6. Move the exhaust camshaft sprocket counterclockwise to take up the belt slack.
  7. Insert a 6mm Allen wrench into the hexagon opening located on the top plate of the belt tensioner pulley. Rotate the top plate counterclockwise until there is no slack on the belt. The tensioner setting notch will start to move clockwise. Watch the notch and continue rotating the top plate counterclockwise until the setting notch is aligned with the spring tang. Using the Allen wrench to prevent the top plate from moving, tighten the tensioner lock bolt to 220 inch lbs. (25 Nm). The setting notch and spring tang should remain aligned after the lock nut is tightened.
  8. Rotate the crankshaft 2 revolutions and recheck the timing marks.
  9. Check the spring tang is within the tolerance window. If not within the window, reinsert the Allen wrench and into the hexagon opening located on the top plate of the belt tensioner pulley. Rotate the top plate counterclockwise until there is no slack on the belt. The tensioner setting notch will start to move clockwise. Watch the notch and continue rotating the top plate counterclockwise until the setting notch is aligned with the spring tang. Using the Allen wrench to prevent the top plate from moving, tighten the tensioner lock bolt to 220 inch lbs. (25 Nm). The setting notch and spring tang should remain aligned after the lock nut is tightened.
  10. Install the engine mount bracket.
  11. Install the front timing belt covers.
  12. Install the A/C compressor/alternator tensioner and pulley assembly.
  13. Install the right engine mount.
  14. Install the crankshaft damper
  15. Install the accessory drive belts and adjust to the proper tension.
  16. Install the right inner splash shield and wheel.
  17. Reconnect the negative battery cable.
  18. Perform the crankshaft and camshaft relearn alignment procedure using the DRB scan tool, or equivalent

Please do not forget to rate and comment about your experience with fixya today... If there is any further assistance i can provide for you please let me know..

Dec 28, 2009 | 2006 Dodge Caravan

1 Answer

Camshaft and crankshaft problem


The camshaft and crankshaft are located internally in the engine. To replace the engine would have to come out and completly rebuilt. Unless you have alot of experience in rebuilding engines I don't reccomend attempting this on your own. These are major compotents and have to be installed and aligned properly.

Sep 21, 2009 | 2004 Chrysler Sebring

1 Answer

1996 Jaguar XJ6: Diagnostic (Check Engine) Camshaft Sensor A


If your car is a 4.0L there are no camshaft sensor. Only crankshaft sensor and timing sensor. Dont know your problem but if your car is not running it is very common that the crankshaft sensor is faulty. It is fairly easy replaced and located just above the crankshaft wheel atthe front of the engine. It is mounted with one 8mm boult.

Apr 30, 2009 | 1995 Jaguar XJ6

2 Answers

Camshaft position sensor location


crank sensor is a component used in an internal combustion engine to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control ignition system timing and other engine parameters. Before electronic crank sensors were available, the distributor would have to be manually adjusted to a timing mark on the engine.

The crank sensor can be used in combination with a similar camshaft position sensor to monitor the relationship between the pistons and valves in the engine, which is particularly important in engines with variable valve timing. It is also commonly the primary source for the measurement of engine speed in revolutions per minute.

Crank sensors in engines are usually comprised of magnets and an inductive coil. They are principally based on the Hall effect. Common mounting locations include the main crank pulley, the flywheel, or occasionally on the crankshaft itself.

Some engines, such as GM's Premium V family utilise crank position sensors which read a reluctor ring integral to the Harmonic Balancer. This is a much more accurate method of determining the position of the crankshaft, and allows the computer to determine within a few degrees the exact position of the crankshaft (and thereby all connected components) at any given time.

Dec 27, 2008 | 2004 Hyundai Santa Fe

1 Answer

Cam timing


Firstly with this engine being identified as an interference engine, I will not accept any responsibility if your engine gets damaged. You are free to take or leave this advice and the responsibility will be entirely yours.

Engine codes: D2H, D6A, D6B, D6D, DDZ, DKZ, DFZ.
Covering years 1989 to 1997.

  • Turn the crankshaft in a clockwise direction to about 10.00 o'clock on the mark on the camshaft sprocket. Good tip here, apply tippex to the sprocket mark.
  • Now slowly continue to turn the crankshaft and with the timing pin feel for the locating hole behind the camshaft sprocket.
  • You will find the camshaft location hole at about 8.00 o'clock.
  • When you have located the the locating hole behind the camshaft sprocket, insert the timing pin.
  • Now insert the timing pin in the crankshaft pulley.
  • You will find the crankshaft pulley location hole behind the sprocket at about 10.30 o'clock.
  • When both timing pins are in their locating holes, the top and bottom of the engine is in-line.
  • This information is only to set the engine up and not to change the timing belt.
  • I would advise that on these engines you change the timing belts at 60,000 miles or every 3 years which ever comes first. If for any reason the timing belt gets contaminated, change the timing belt.
Take care.

Nov 28, 2008 | 1991 Peugeot 405

Not finding what you are looking for?
1999 Peugeot 206 Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

scj103

Level 2 Expert

99 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...