Question about 1995 Pontiac Grand Am

Open Question

I have a 1995 pontiac grand am and need to know where the program connector is inthe trunck to program the key fob a picture would help

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 341 Answers

SOURCE: Do key fobs loose memory (06 Pontiac Grand Prix)

do you have the owner manuals .... it tells you how to program them for that car

Posted on Dec 11, 2008

Ad
  • 7 Answers

SOURCE: 2005 Pontiac SV6 Montana key fob unlocks doors but will not lock

For the sliding doors you need to clean the contacts, there are 6 or 8 on both sides, just wipe them clean as they are probably covered in oil/grease/grime.

Posted on Feb 14, 2009

  • 401 Answers

SOURCE: how do i program a key fob for a 2006 Pontiac

you will need to take it to a dealer or some place that has a scanner to program key fobs
IMORTANT TAKE ALL THE KEY FOBS WITH YOU
once the vehicle is put in the learn mode all the fobs have to be programed

Posted on Nov 10, 2009

Molson02536
  • 3854 Answers

SOURCE: How do I reset a Key Fob for my 2006 Grand Prix

No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.

Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.
Perform the following steps: Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.

Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Posted on Nov 13, 2009

  • 25 Answers

SOURCE: timing specs

this procedure is not for the beginner,if you feel ok about the work then i would suggest you purchase a haynes service manual which are very thorough.p.s.the other solution was very thorough just short of photos which a manual will have.no worries pardner.

Posted on Jan 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the wire look like that you use to program a key fob picture of where it is or what it looks like


Not a picture, but may help.
the program line-a dark green wire with a molded insulator
(usually red) on the end.

Dec 03, 2015 | 1995 Plymouth Grand Voyager

1 Answer

How to program a 2002 pontiac grand am key fobe


Go to youtube watch a video this will help u understand the procedure

Mar 03, 2014 | 2002 Pontiac Grand Am

1 Answer

How do I program my remote key fob for a 2007 pontiac grand prix?


Hey Lisa,
You are going to have to take the car and the key fobs to the dealership .
They will need all of the fobs , as they are all going to need to be reprogramed at once ;
The fob on an 07 Pontiac only can be programed using a diagnostic scan tool .
They will connect the scan tool to the vehicle.
Turn key to on position.
Select 1 body,
then select special functions
then select program key fob,
select the number of key fobs you want programed.
Press and hold the lock and unlock key simultaneously for about 15 seconds until the power locks cycle to confirm the remote is programed.

Nov 05, 2011 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

How do I program a new key fob for a 2007 Grand Prix? Bought a replacement on e-bay.


Hey Lisa,
You are going to have to take the car and the key fobs to the dealership .
They will need all of the fobs , as they are all going to need to be reprogramed at once ;
The fob on an 07 Pontiac only can be programed using a diagnostic scan tool .
They will connect the scan tool to the vehicle.
Turn key to on position.
Select 1 body,
then select special functions
then select program key fob,
select the number of key fobs you want programed.
Press and hold the lock and unlock key simultaneously for about 15 seconds until the power locks cycle to confirm the remote is programed.

Nov 05, 2011 | 2007 Pontiac Grand Prix GXP Sedan

2 Answers

The key fob for my 2006 Pontiac Grand Prix will not work. I have checked the battery & that is not the problem. Is there a program to reset the key fob?


The key fobs stop working because the solder joints that hold the battery in place break free. Very easy to fix with a little solder and a soldering iron. I just fixed a bunch of them for people I know including BOTH of the fobs for our 2006 GP GT. Takes about 5 minutes each.

Sep 26, 2010 | 2006 Pontiac Grand Prix

1 Answer

How do i program the key fob on my 2003 grand am se


Hi
to program your key fobs you need to take the vehicle to a dealer or shop with a scanner to enable the program mode
IMPORTANT take ALL the KEY FOBS
hope this helps

Aug 17, 2010 | 2003 Pontiac Grand Am

1 Answer

How do i program a key fob for a 2006 Pontiac Grand Prix. I have a new one I just need to program it


you will need to take it to a dealer or some place that has a scanner to program key fobs
IMORTANT TAKE ALL THE KEY FOBS WITH YOU
once the vehicle is put in the learn mode all the fobs have to be programed

Nov 09, 2009 | 2006 Pontiac Grand Prix

1 Answer

Do key fobs loose memory (06 Pontiac Grand Prix)


do you have the owner manuals .... it tells you how to program them for that car

Dec 11, 2008 | 2006 Pontiac Grand Prix

2 Answers

Programming a 2006 Pontiac Gran Prix Keyless remote


The rke on 06 pontiac only can be programed using a diagnostic scan tool or Tech 2.
Conect the scan tool to the vehicle. turn key to on position.
Select 1 body, 2 them select special funtions
3 slect program key fob,
4 select the number of key fob you want to program.
5 Press and hold the lock and unlock key simultaneous. about 15 seconds
The power lock cycle confirm the remote is programed.

Jul 03, 2008 | 2006 Pontiac Grand Prix

Not finding what you are looking for?
1995 Pontiac Grand Am Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...