Question about 2003 Ford Focus

1 Answer

Focus st 170 mk1 2003 torque setting for both camshaft pulleys worryed in case i have not got it tight enough Thanks John

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Ford Expert
  • 201 Answers

First time it is 60 psi second time 70 psi and finally third time 80 psi should be ok

Posted on Apr 15, 2017

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 701 Answers

SOURCE: what is the camshaft pulley

Hello mudpie67: My name is Roger and I will help with your question. The correct torque value for the camshaft gear is 115(n.m) or 85 (ft.lbs.) Should You need further help? Please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Posted on May 28, 2011

nookymonsta
  • 1 Answer

SOURCE: i need camshaft bearing cap

Maybe for a Main bearing Cap, Certainly not for a Cam bearing

Posted on Apr 14, 2013

  • 58 Answers

SOURCE: Hi I need torque settings for camshaft caps on the ford focus tdci 1800 .

  1. Tighten all bolts in a single sequence to 50 Nm
  2. Back the bolts off 1/2 turn.
  3. Tighten the bolts in sequence shown to 50 Nm .
  4. Rotate all the bolts in a single sequence an additional180 degrees in two steps of 90 degrees each.
9 3 1 5 7
8 6 2 4 10 sequence for head


Spec for rod 38Nm

Posted on Jul 10, 2015

  • 53746 Answers

SOURCE: I need torque spec. For camshaft pulley bolt on 2004 dodge stratus

2004 dodge stratus 2.7 L v6 200i--2006 engine identification is EER has twin cam shafts and the bolts that hold the sprockets to the cam shaft are at 21 ft/lbs
there are 4 bolts for each cam (autodata publication page 375)
if this is not your engine then comment as to how many cam shafts it has as there are many different settings for different dodge engines

Posted on Oct 26, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specifications


Head bolts are torqued in 3 steps, 1-18ft.lbs, 2-60 degrees, 3-60 degrees, camshaft caps-10-11 ftlbs, intake manifold-12-17ftlbs, exh manifolds-32-40 ftlbs, camshaft pulley-74-89 ftlbs.

Feb 05, 2014 | Cars & Trucks

1 Answer

I have this 89 acura legend 2.7l v6 timing belt removed and the water pump removed, the old pump failed which caused the belt to fail, i have new parts and the pump installed only i dont understand to...


Hi, here is what you need to do. Get all of the timing marks lined up as indicated in the picture below. Put the belt on. Without moving the gears off their marks, make the belt tight across the cam gears and then down the right side to the crank gear. All of the slack must be on the left side to be taken up by the tensioner. Release the tensioner to tighten the belt and then verify the marks are still aligned. If the marks are not aligned, loosen the tensioner just enough to turn the gear that needs to be realigned. After tensioning the belt, rotate the crankshaft clockwise 720 degrees and recheck the timing marks. I have pasted the book procedure below. Please let me know if you still have questions. You must get this right.

jturcotte_2242.gif

jturcotte_2243.gif



jturcotte_2244.gif



jturcotte_2241.gif

  1. If the crankshaft or camshafts have been turned with the timing belt removed, remove the spark plugs and advance the crankshaft about 15 degrees beyond TDC of No. 1 cylinder. Make sure the camshaft sprockets are properly aligned with the marks and return the crankshaft to the TDC mark.
  2. Install the belt in sequence on the crankshaft, the front camshaft, water pump and tensioner pulleys, then the rear camshaft.
  3. To adjust the tension, loosen the tensioner pulley bolt about 1 / 2 turn. The spring will automatically set the proper tension. Torque the bolt to 31 ft. lbs. (43 Nm).
  4. Rotate the crankshaft 6 turns clockwise and check that the timing marks on the crankshaft and camshafts align properly. Adjust the timing belt tension again by rotating the crankshaft to the align the blue mark on the pulley with the pointer. Loosen and retorque the tensioner pulley bolt.
  5. Install the remaining parts in reverse order. Torque the crankshaft pulley bolt to 83 ft. lbs. (115 Nm). When installing the side mount bracket, torque the bolts to 40 ft. lbs. (55 Nm).

Sep 13, 2011 | Acura Legend Cars & Trucks

1 Answer

How do I change the timing belt on my 1991 chevy lumina 3.1?


Things You'll Need:
  • 2 camshaft timing clamps (#J38613-A)
  • Set of metric ½-inch drive sockets
  • Set of metric 3/8-inch drive sockets
  • Set of metric ¼-inch drive sockets
  • ½-inch drive ratchet
  • ½-inch drive air gun
  • ½-inch extensions (4 to 8 inches long)
  • 3/8-inch drive ratchet
  • 3/8-inch drive air gun
  • 3/8-inch extensions (4 to 8 inches long)
  • ¼-inch drive ratchet
  • ¼-inch drive air gun
  • ¼-inch extensions (4 to 8 inches long)
  • Pry bar
  • Common screwdriver
  • Small common screwdriver
  • Small piece of wire at least 1.85 inches long
  • Phillips screwdriver
  • Pliers
  • Adjustable wrench
  • Torque wrench
    Removing the Timing Belt
  1. Remove the air cleaner, air duct and the coolant reservoir. The coolant reservoir can remain attached to the hoses---just unbolt it and move it to the side out of your way. Remove the serpentine belt. Before removing the serpentine belt, make sure there is a diagram on the hood or radiator support to show you the belt routing. If the belt routing sticker is missing, sketch out a picture of the belt routing.
  2. Siphon the fluid out of the reservoir of the power steering pump, or be prepared to cap the line ports off. You can cap the line ports off with a piece of rubber hose. Close the open end of the hose with a large bolt. Unbolt the power steering pump from its bracket and set it aside. Cap any open hose ends or pipe fittings. This will prevent additional fluid loss.
  3. Remove the right timing belt cover, spark plug wire cover, left timing belt cover and the ECM harness cover using the ¼-inch tools. Remove the serpentine belt tensioner with the 3/8-inch tools. Unclip the power steering hose from the alternator. Using the ¼-inch tools or the 3/8-inch tools, remove the center timing belt cover and the right and left camshaft covers.
  4. Remove the tensioner side plate. The side plate is located just under the left cams and has three bolts holding it on. The tensioner is hydraulic and includes a plunger unit. Turn the plunger unit to remove it from the pulley arm and socket. Make sure you do not lose the tapered brush that sits between the plunger and the mount. Loosen and remove the tensioner pulley bolt (located at about 10 o'clock on the tensioner pulley). Tape the pulley pivot bushing to the pulley so it doesn't fall out. Remove the pulley and the arm. Remove the timing belt.
  5. Installing the Timing Belt
  6. Bend a thick paper clip so you have a straight piece of wire at least 1.85 inches long. Clamp the tensioner plunger at its center in a vise, with the plunger pointing toward the ground. Allow it to sit for 5 minutes to get the oil into the rubber boot. Remove the plug from the flat base of the plunger and insert a small screwdriver into the vent hole. Turn the screwdriver counterclockwise until the pushrod is retracted. Make sure the pushrod is fully retracted before moving on to the next step.
  7. Push the wire peg you created in Step 1 into the vent hole and turn the screwdriver counterclockwise until you feel the wire peg lock into the pushrod. Fill the plunger with 5W-30 synthetic engine oil to the bottom of the hole. Do not overfill the plunger. Put the plug back on the plunger. Make sure the plug is in securely and the plunger is completely sealed. Wipe the plunger clean of spilled oil.
  8. Clean the tensioner pulley, but do not lubricate it. Turn the crankshaft clockwise until the number 1 cylinder (front cylinder on the driver's side) is at top dead center and the timing marks on the crank pulley and the block are lined up. Top dead center is achieved when the piston in the number 1 hole reaches its complete height in the rotation. You can feel for this by sticking a screwdriver in number 1 spark plug hole while turning the crank pulley.
  9. Turn all four of the camshaft pulleys so that the machined flats are facing up. Install the timing clamps on each camshaft carrier. Torque the bolt on the timing clamp to 22 foot pounds of torque. If there are any timing marks drawn on the camshaft pulleys, erase them.

  10. Loosen the camshaft sprocket bolts. Using a rubber hammer, tap each camshaft sprocket to remove any taper. Tighten the sprocket bolts finger-tight. Spin each sprocket to be sure the sprocket turns freely. Make sure there is no back and forth freeplay when the sprockets are being turned.
  11. Install the timing belt starting with the crankshaft pulley. Route the belt to the right guide pulley (as you are facing the engine), then the right exhaust camshaft sprocket, over the top of the right intake camshaft sprocket, then under the center guide pulley, over the left intake camshaft sprocket and over the left exhaust camshaft sprocket. Make sure the timing belt is tight on the right side and loose on the left side (again, as you are facing the engine).
  12. Install the tensioner pulley, making sure the pivot brush does not fall out. Leave it taped or use a magnet to hold it in. Torque the tensioner pulley bolt to 37 foot pounds of torque. Install the tensioner and the side plate. Be sure the pushrod end is seated properly against the tensioner pulley. Torque the side plate retaining bolts to 18 foot pounds of torque. Remove the locking pin and let the plunger extend to its normal position.
  13. Set the torque wrench to 89 foot pounds of torque, then put the torque wrench on the square lug of the tensioner and torque it. This applies initial tension to the timing belt. Turn the crankshaft sprocket three times by hand. This ensures seating of the timing belt and makes sure the engine turns freely without the valves hitting the pistons. Check to be sure the crankshaft pulley timing marks are still lined up.
  14. Torque the bolts on the left camshaft exhaust and intake pulleys to 96 foot pounds of torque. You will need to hold the sprockets to keep them from turning while torquing the bolts. Remove the timing clamp from the left side camshaft carrier. The cams should not move when removing the timing clamp. Turn the crankshaft one complete clockwise rotation and align the crankshaft pulley marks.
  15. Repeat Step 9 for the right camshaft exhaust and intake pulleys, expect when turning the engine, turn it two complete clockwise rotations and align the crankshaft pulley marks. The flat, machined surfaces on the camshafts will be facing up on one side and facing down on the other side.
  16. Mark the left camshaft exhaust pulley at 2 o'clock and the left camshaft intake pulley at 8 o'clock (the marks should be in line with each other) with fingernail polish or heat paint. Mark the right camshaft exhaust pulley at 10 o'clock and the right camshaft intake pulley at 4 o'clock, lining up the marks. Install all components in the reverse order of removal.

Feb 15, 2011 | 1991 Chevrolet Lumina

1 Answer

Camshaft torque settings ford puma 1.4




Crankshaft Belt Pulley 85 ft.lb


Rear crankshaft oil seal carrier 15 ft.lb
Camshaft Timing Belt Pulleys 50 ft.lb

Camshaft timing belt pulleys 50 ft.lbrejakwilson.gif

Same TIGHTENING Sequence for Single OHC


rejakwilson_0.gif

Nov 24, 2010 | 2000 Ford Focus

1 Answer

Would like information on timing belt settings on a 1993 Isuzu Rodeo 4X4 3.2 We have already bought the book. It seems that the setting still are not what this particular motor/engine needs are there other...


look for timing marks????
Align groove of crankshaft timing pulley with mark on oil pump.
Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate. (i can email pic if needed)
When timing marks are aligned, no pistons will be on T.D.C.
install timing belt. Align the dotted alignment mark on the timing belt with the mark on the crankshaft gear.
For correct belt installation, the letters the belt must be able to be read as viewed from the front of the vehicle. It is recommended for easy installation that the belt be secured with double clips after it is installed to each pulley. Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Turn the crankshaft counterclockwise to remove the belt slack between the crankshaft timing pulley and the RH bank camshaft timing pulley.
Install the belt on the water pump pulley. Remove double clips from pulleys. Turn the crankshaft pulley clockwise by two turns. Measure the rod protrusion to ensure it is within the standard. Standard 4-6 mm (0.16-0.24 in)


13) If out of standard, remove pusher, loosen adjusting bolt, and readjust. (Repeat from step 11). Tighten adjusting bolt to the specified torque. Torque 42 N-m (31 lb-ft)


  1. Pusher
    • Tighten bolt to the specified torque.
Torque 19 N-m (19 lb-ft)


  1. Timing belt cover
    • Remove crankshaft pulley that was installed in step 9.
    • Tighten bolts to the specified torque.
Torque 17 N-m (12 lb-ft)


  1. Oil cooler hose
    • Tighten oil cooler hose bracket bolts to the specified torque.
Torque 22 N-m (16 lb-ft)


  1. Crankshaft pulley assembly
    • Using special tool J-8614-01, hold the crankshaft pulley.
    • Tighten center bolt to the specified torque.
Torque 167 N-m (123 lb-ft)


  1. Crankshaft pulley; P/S belt
    • Tighten fixing bolt to the specified torque.
Install the belt on the idler pulley.

Mar 07, 2010 | 1993 Isuzu Rodeo

1 Answer

Ford focus wheel nut torque setting for alloy wheels.


hi we set them at 100nm which is tight enough and all so tight enough so you can undo them at the side of the road if you need to regards

Jan 21, 2010 | 2001 Ford Focus

1 Answer

How to install timing belt on 1998 vw beetle


Instructions
Things You'll Need: · Set of quarter-inch drive sockets Quarter-inch drive ratchet Set of half-inch drive sockets Half-inch drive air gun Set of metric wrenches Special tools for holding camshaft timing #2065-A and injection pump #2064

Step 1

Remove the accessory drive belts and the accessory drive belt tensioner. Remove the upper timing belt cover and the valve cover. Turn the crankshaft clockwise until the No.1 cylinder is atop, dead center, with the flywheel timing marks aligned.

Step 2

Install the special tool setting bar (#2065-A) on the rear of the camshaft. If it does not fit, turn the crankshaft once more and line up the timing marks again in the hole of the transmission housing.

Step 3

Insert locking pin #2064 into the injection pump to hold it in position. Remove the crankshaft pulley bolts, the crankshaft pulley and the lower timing belt cover. Loosen the tensioner pulley nut and allow the tensioner to move away from the belt. Loosely tighten the nut to hold the tensioner out of the way. Remove the top guide pulley and the timing belt.

Step 4

Make sure that the timing mark on the flywheel is lined up and that the camshaft setting bar and injection locking pin are in place. Loosen the camshaft bolt a half turn and tap the sprocket with a soft mallet to loosen it off its taper. The sprocket should move freely. Install the top guide pulley and torque to 18 foot pounds of torque.

Step 5

Install the new timing belt, starting on the right side and working counterclockwise. Keep the tension on the right nontensioned side. Loosen the tensioner pulley nut. Using the two-pin wrench, turn the tensioner pulley clockwise until the notch and raised mark are aligned. Torque the tensioner pulley nut to 15 foot pounds of torque. Make sure the flywheel timing mark is still aligned.

Step 6

Torque the camshaft bolt to 33 foot pounds of torque. Remove the locking pin from the injection pump and remove the camshaft setting bar. Turn the crankshaft two turns and check the alignment on the flywheel. Make sure that the setting bar can be inserted easily and that the injection pump locking pin can be inserted. Install all components in reverse order of removal and torque the crankshaft bolt to 18 foot pounds of torque.

My Recommendation - Pay an authorized VW mechanic $500 to replace the timing belt water pump an tensioner, and sleep better knowing that the job was done right. Just too many places for a novice car mechanic to screw up. jQuery('.article ol .image').each(function(i,e){ var $this = jQuery(this); $this.find('img').error(function(){ jQuery(this).remove(); $this.remove(); }); });

Oct 06, 2009 | 1998 Volkswagen Beetle

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...