Question about 2004 GMC Envoy

Open Question

2004 gmc envoy. changed ignition lock cylinder, now key wont turn back to off position

Car starts but when shut it off wont turn past acc positon.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
CRTN
  • 716 Answers

SOURCE: ignition switch or ignition cylinder??

Ignition Switch They Are Always Going Bad Your Lucky You Can Get It Acc Mode Mine Wouldn't Turn At All. I Went After Market Through A Much Cheaper Version From Autozone But Now I Have One Key For The Door And Another For The Ignition.

Posted on Jan 30, 2009

Ad
jimmy nutron
  • 132 Answers

SOURCE: key stuck in ignition halfway to ACC position and will not turn

try wd40 and shaking the key, what happens is one of the tumblers get stuck and wont let the key turn if that dosnt work let me know worst case you will have to replace the ignition its about $35 to $40 and a few hours.

Posted on Jun 01, 2009

  • 743 Answers

SOURCE: 1994 Saturn SL2 Key stuck in ignition cylinder

Put some pressure on the steering wheel in one direction or the other this may take the pressure off the cylinder itself and allow you to do what is needed...hope this works.

Posted on Nov 16, 2009

  • 4 Answers

SOURCE: mitsubishi galant 2004 key stuck in ignition

1st Remove Battery cable from Battery because the only time the air bags will deploy is when the key is in the ignition. I have tilt steering and when I put the steering wheel in the up most position. I came right out. But now it seems to stick more lately.

Posted on Jan 02, 2010

  • 82 Answers

SOURCE: 2005 GMC Envoy key is stuck in accessory position

Jump starting the battery may be all you need. If this vehicle was not in park when the battery went dead and when you got in to start it it was dead. You then probably put it into park trying to start it.
But the issue at this time is if it was in neutral when the battery went dead the you changing the selector to park may not actually have placed the transmission in park. With electronic gear selection it actually need power to the system to place the transmission in park.
Without it really being in park the key may move to the lock position.
A bit of quess work here but I hope for you I hit the mark.

Posted on May 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 gmc envoy. key wont turn in the ignition, wheel is not locked shifter wont move, and brakes are very stiff. looks like key wasn't all the way in off postion when removed


The lock cylinder may be jammed and will probably need to be pulled and fixed or replaced. Excessive wear over time with the pins in the cylinder can cause this, particularly with older vehicles.

Jul 03, 2017 | GMC Cars & Trucks

1 Answer

I have a 2004 gmc envoy and the security light came on what does this mean?


  1. 2004 GMC Envoy Security light car not start - Questions - Fixya

    www.fixya.com > ... > GMC > Envoy > 2004 GMC Envoy...will not start replaced ignition switch and car will not turn over. Is the security light on ?If your truck has a pass key system, the sensor in the lock may not be ...
    ON GOOGLE

Jul 15, 2015 | GMC Cars & Trucks

2 Answers

Ok 03 Yukon, at first not running but after being towed home it hit a bump and all the lights came on. Took it off the wrecker it started right up, but nothing electrical in cab works, and now it won'


It might possibly be the ignition switch, or the linkage to it.

They reason I suspect this is your statement, "I bumped the key forward and it will engage the starter but still wont shut off"

The part where you insert the key is really a "cylinder lock", that then transfers the turning motion to the actual "ignition switch"

My wife had a Pontiac (also a GM product) that the cylinder lock had a linkage that went to the ignition switch (similar to a sliding electric switch, with the 4 positions, ACC, OFF, RUN, START), which was bolted on further down the steering column, underneath the plastic covering on the column.

Another person here had a similar problem, and after suggesting this, he wrote back that he removed his steering column cover and found a screw opposite the cylinder lock that had loosened and fallen out.

So you could try removing the steering column cover and see if all is ok.

Also, when you have it opened up, observe the action as you turn the key, as the problem could be the cylinder lock itself.

Jan 28, 2014 | 2003 GMC Yukon XL

1 Answer

How do I remove the ignition lock on my 1998 Mazda Protege? Tumblers are stuck. Key won't go past accessory.


if ou do not have the key, look at the replacement lock there'll be a tab which recesses when the key is turned to acc or on position. It is that tab which prevents you from removing lock cylinder it has to be forced into a recessed position or drilled to where the cylinder can removed. If u do then locate tab turn key to acc or on and push tab to recessed position and remove cylinder.

May 31, 2012 | 1998 Mazda Protege

1 Answer

Key stuck in 2004 gmc envoy and car will not start


make sure battery is 12.6 volts. if not you not going to be able to get transmission go all the way in park to remove ignition key.when you press brake pedal it energize brake transmission shift interlock to get transmission all way in park to remove ignition key.if all is good battery is 12.6 volts.sound like ignition switch lock cylinder broken more likely.

Nov 06, 2011 | 2004 GMC Envoy

1 Answer

Location of ignition switch on 2006 gmc envoy


PATH: Chassis Electrical > Instruments & Switches > Ignition Switch > Removal & Installation Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disable the airbag system, as outlined in the Chassis Electrical Section.
  3. Remove the hush and knee bolster.
  4. Remove the steering column trim covers.
  5. With the key installed, turn the key to the RUN position.
  6. Install a hex wrench into the hole on top of the lock cylinder housing. Push down on the hex wrench to release the tab on the lock cylinder inside the lock cylinder housing.
49901b3.gif
Push down on the hex wrench to release the tab on the lock cylinder inside the lock cylinder housing

  1. Slide the lock cylinder out of the lock cylinder housing.
  2. Disconnect the passlock and key buzzer from the lock cylinder housing.
  3. Insert into the lock cylinder housing
0bc8f9a.gif
Release the tabs on the ignition switch using ignition switch connector release tool J 42759

  1. Pull the ignition switch out of the lock cylinder housing.
  2. Disconnect the connector from the ignition switch.
To install:
  1. Verify the alignment of the gear in the ignition switch. If gear is not in position shown, turn gear in ignition switch until you reach the correct position.
  2. Use a screwdriver to rotate the lock cylinder housing gear counterclockwise until it hits a stop. In order to reach a stop while rotating the lock cylinder housing gear you MUST push and hold in the solenoid on the electric park lock.
  3. Connect the connector to the ignition switch.
  4. Insert the ignition switch into the lock cylinder housing. The tabs on the ignition switch MUST be seated inside the lock cylinder housing for proper installation.
  5. Use a screwdriver to rotate the lock cylinder housing gear clockwise to the start position—allowing it to spring return into the RUN position.
52c72cb.gif
Use a screwdriver to rotate the lock cylinder housing gear clockwise to the START position

  1. Align the lock cylinder and install the lock cylinder into the lock cylinder housing.
  2. Connect the passlock and key buzzer into the lock housing.
  3. Install the steering column trim covers.
  4. Install the hush and knee bolster.
  5. Enable the airbag system, as outlined in the Chassis Electrical Section.
  6. Connect the negative battery cable.

Oct 12, 2009 | 2006 GMC Envoy

1 Answer

My key will start the car but it wont turn the car off i have to unplulg the distributor to kill theh car. Also the ignition switch in the car rotates all the way around but it has always done that it just...


the ignition switch is an electrical part. The lock cylinder is whre the key goes and it activates the ignition switch. If you pulled the lock cylinder out, you could operate the car with a screwdriver.
Either you have damaged the ignition switch where the lock cylinder goes into it, or the lock cylinder is damaged where it fits into the ignition switch.

this is 96 taurus, don't have 92 sorry

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.
------------------
Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Ignition Switch The ignition switch (11572), which is mounted on the steering actuator housing (3F723), operates in the following manner:
  • The ignition switch is cycled through rotation of the ignition switch lock cylinder (11582) through a pin which is part of the ignition switch.
  • The ignition switch lock cylinder also controls the mechanism which provides a positive lock for the transaxle linkage and the steering system.
  • The locking mechanism is located in the steering column housing.
The ignition switch lock cylinder positions are:
  • ACC
  • LOCK
  • OFF
  • RUN
  • START
The key can be removed from the ignition switch lock cylinder with the column-shift transaxle only when the shift lever is in PARK position and the key is in LOCK position.
  • The ACC position operates while the steering and transaxle remain locked.
  • The engine shuts off when the key is turned to the OFF position without locking the steering or transaxle.
Blade Type
The ignition switch has blade-type terminals that engage with one multiple connector. The multiple connector is secured to the ignition switch by an integral connector fastener.

May 05, 2009 | 1992 Mercury Sable

1 Answer

Key broke off in column


If you can get it to turn tothe on position (wait to start position) you should be able to locate the lock pin in the lock cylinder (may have to pull off lower plastic part of column to access) push up on the pin with a small punch or drill bit (with ignition in on position) and pull out the lock cylinder assembly. Be careful, there may be a gear inside that should come out with lock cylinder, use caution when installing new cylinder to make sure it is installed in the proper positon. Hope this helps.

Mar 11, 2009 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

I have a 2004 GMC ENVOY I got in it started it pressed the brake and could not put it in gear. I tried to turn the ignition switch off but would not go back far enough to take the key out.I have no power...


your ignition is bad, replace the ignition and your problem should be solved....

Note: if you have not done this before, you may want to have a shop do it for you.

Nov 26, 2008 | 2004 GMC Envoy

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...