Question about 2003 Pontiac Grand Am

Open Question

I need an asembly diagram for the clutch push rod on a 2003 grand am. The clip broke and now the pedal goes to the floor and stays there. I had to buy the complete push rod but only needed the clip. Nothing new there. I need a drawing of how it connects to the pedal. The Haynes manual was of no help.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need a clutch pedal diagram for a 1999 s10 2.2 4cyl manual trans


Sorry no diagram. But here is how it works. In the start position(Power) the wire goes to the start fuse, from the fuse it goes to the clutch pedal switch. Push the pedal and it goes to the starter relay. On the other end is ground. If it is good it pulls the relay closed. On the closed end is battery power to the starter.

Mar 09, 2016 | 1999 Chevrolet Silverado 1500

1 Answer

New clutch installed. No pedal, stays on floor unless I bring it back up with my hand. No resistance.


`Did it bleed, did fluid come out in a steady stream? Isn't there a spring to bring the pedal off the floor?
Check the linkage of the pedal to rod to the clutch master cylinder, make sure that is all together. Any chance the master has an internal leak and won't build hydraulic pressure down at the slave? If you get it bled, then watch the slave operation while someone works the clutch pedal. The piston on the slave should extend and push the clutch fork enough to disengage the clutch.

Jul 19, 2015 | Nissan Cars & Trucks

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

1 Answer

Grand am clutch pedal


try opening the bleed nipple on the slave cylinder so that you are not trying to press against the pressure plate when you push the rod into the master cylinder.

Dec 14, 2013 | Cars & Trucks

1 Answer

Clutch goes to floor houseing broke


clutch master.(master cylinder)

Aug 21, 2012 | 2003 GMC Sierra 1500

1 Answer

Clutch pedal stays at floor - will not come back up


clutch pedal broke .autoadjuster broke ,clutch thrust bearing has gone through clutch pressure plate operating fingers ,clutch operating arm has broke

Dec 05, 2010 | 2004 Pontiac Grand Am

1 Answer

Clutch pedal went to floor no fluid loss push rod disassembled


Hi:
If your clutch reservoir is still full, you have had a failure of either the clutch master cylinder, or the clutch slave cylinder.

Nov 11, 2009 | 1993 Jeep Grand Cherokee

2 Answers

Clutch pedal went to the floor but did not come back up. Heard something 'pop' when pushing in clutch last night. Got home, then tried to start car this morning and clutch made a 'pop' sound again when...


there is a plastic clip that connects the clutch pedal to the rod that goes to the master cylinder, chances are that it let go. Bad thing is that it is only available from GM along with the rod. It is around 50

Oct 16, 2009 | 2003 Oldsmobile Alero

2 Answers

Clutch pedal stays to the floor and car is now stuck in neutral. Can raise the pedal with hand but will not raise on it's own


clutch hydralics is gone, meaning you have a leak, check clutch master cylinder, see if its empty, if so refill and pump pedal sevarel time may have to lift by hand sometimes then look for a leak,most times it the slave cylinder,thats what pushs clutch fork to disengage clutch. hope this is helpful good luck.

Oct 15, 2009 | 2003 Pontiac Sunfire

3 Answers

Clutch pedal suddenly went to floor with a clunk Tranny or cluthch linkage?


man might just be the same thing as me the pushrod operating lever broke...push rod might of went through pressure plate also easy on your clutch...but ya take tire off left side take green cap off and check that little lever thingy if its broke

Apr 20, 2009 | 1991 Volkswagen Jetta

Not finding what you are looking for?
2003 Pontiac Grand Am Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...