Question about Peugeot 206

Open Question

Hi, the rpm of my Peugeot 206 is on 1250 rpm. I change the a new idle sensor. How can I adjust z rpm around 800 rpm at idle time?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 183 Answers

SOURCE: Idle problem

Yes you can,

do this with your RPM setting,

you ahve to just set you engine race settings,

try & having funn with your car,

THNX

Posted on May 18, 2008

Ad
alicantecoli
  • 22484 Answers

SOURCE: how to increase idle speed on peugeot 405 sti

carb? mono point injection or multi point injection.check for a thin rubber air hose that runs to ign module is it intact or sucking in air caused by being perished also the thin pipe running to the air intake cold /hot ,flap control .if carb then it has a adjusting screw ,and mono point but multipoint is different.91 model also uses a distributor which could be advanced a slightly ,check the same sort of air pipe to the gearbox as iam sure this year has a pipe to operate the gearchange.any of these pipes sucking air can cause your problem

Posted on Nov 20, 2008

  • 84 Answers

SOURCE: 1999 passat tdi power fault

Air mass sensor, almost never shows codes but always makes the vehicle loose power !! cheaper from vw than pattern and more reliable

Posted on Dec 24, 2008

alicantecoli
  • 22484 Answers

SOURCE: idling problems

their should be a hand idle control somewhere on this vehicle ??

Posted on May 08, 2009

  • 1 Answer

SOURCE: vw polo 1 litre has idling problems it keeps revin...

im also havin a problm with 99 polo 1.6 it revs high low high low and if da tank is below 1/4 it dies of while driving iv changed tank unit,trottle body, sensor nd after i changd tank unit da foat reads opsite way sum1 plz help me

Posted on Feb 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the ignition timing for 2002 nissan hardbody 2000i 16v


Here are the 3 engines listed for this year. IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 2.4L SFI 4cyl

The Ignition Timing

18-22 DegreesBefore top dead center - When throttle positionsensor disconnected and using suitably programmedscan tool.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (750-850 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (700-800 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI SC 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chockdrive wheels, curb idle speed (700-800 RPM)transmission in neutral.

Jun 05, 2015 | Nissan Hardbody Cars & Trucks

1 Answer

What is the idle speed 3.0 V6 chrysler 1994. I need to set the timing and nowhere does it mention the idle speed


Well the idle speed is computer controlled, so there's no adjustment.
Normal idle is around 800 rpm.

Mar 08, 2014 | 1994 Chrysler LeBaron

2 Answers

Taurus 2002 idle


most have an idle stop screw thats adjustable with a phillips screwdrivewr or a nutdriver head..need to adjust this to between 750-800 minimum..your oil light will go out and proper rpm on the alternator will be achieved..

Jan 21, 2014 | Cars & Trucks

2 Answers

Its idling rough


Hi.

Check idle air control system (valve, hoses and wires). Check air intake and check the sensors installed in the air intake. Check vacuum for leaks.

Those listed are the most common faults causing fast idle in this type of engine.

Regards.

Ginko

Dec 15, 2011 | 2002 Mitsubishi Lancer

2 Answers

1990 f150 larriat. V-8, I believe the engine should idle around 750 rpm. I tried using a timing light and adjust the timing but the it would not work with advancing the timing. Is there anything else...


YOU CAN PUT THE TIMING BACK TO ORIGINAL POSITION! ON TOP OF THE MOTOR! IF IT IS CARBURATED, YOU CAN ADJUST THE IDLE SCREW TO RAISE IDLE! IT WILL BE A SMALL SCREW LOCATED BEHIND THE THROTTLE PLATE! ON FUEL INJECTED MOTOR, IT IS LOCATED UNDER THE COVER WHERE THE THROTTLE CABLE GOES INTO! YOU WILL SEE A SMALL SCREW BEHIND THE THROTTLE PLATE! THE PLATE IS A RECTANGULAR PLATE THAT YOU CAN MOVE TO INCREASE THE IDLE BY HAND! I OWN A 93'!

Mar 02, 2011 | 1990 Ford F150

2 Answers

Need to adjust my idle how do i do that


air idle control valve, I dont belive you have a ideler set screw..I do belive the problem is what I have Listed..........Best of luck


How can I tell if I need a new air idle control valve?
If your car has a rough idle or the idle cycles up and down, then chances are that you have a bad idle control valve. On modern vehicles, the purpose of the idle air control valve is to regulate your idle, and keep the idle smooth. The idle valve is controlled by the ECU or the computer, and when in gear the idle should be between 800 and 1000 rpm, and not in gear, between 700 and 900 rpm

Dec 02, 2010 | 1999 Oldsmobile Alero

1 Answer

Rpm and acceleration problem


throttle sensor fault. might be cleanable if removed. also could be a damaged idle valve, might be staying open this cal also give high revs. and tap and it will go down as its sticking. acceleration is the throttle sensor i may have blank spots. removing it and spraying in the switch breather hole and shake the cleaner around and turning it at the same time should clean the sensor. then shake and leave to drain out the cleaner. idle valve you will need to remove it and clean ti with some carb cleaner and a brush like toothbrush, clean it thorley out push the pin in and out to make sure its not sticking at same time spray it. then when clean leave to dry. then refit them. hope this helps

Jun 24, 2017 | 1999 BMW 318 ti

2 Answers

My 99 suburban idles at 1000 rpm in park with a new TPS at operating temp. What is the factory idle setting? how do I adjust rpm?


There no adjustment for idle, control by computer, TPS reading should be .50 volt's, you could have a vacum leak, check vacum line and check for vacum leak at base of intake manifold.

Jan 21, 2010 | 1999 GMC Suburban

1 Answer

Idle speed high


Sounds like the tps (throttle position sensor) is either defective, or out of adjustment. Need an oscilloscope to check, so see a mechanic. Could also be vacuum leak. check lines for cracks and leaks

Oct 19, 2009 | 1990 Isuzu Trooper

3 Answers

1992 chevy blazer idols too low when engine is cold it idols around 800 rpm but when it warms up it drops down to around 400 rpm n alittle lower when i put it in gear


The problem is in the idle air control motor. It is mounted on the throttle body with two bolts, you can pull it off and make sure it is not caked with carbon also check where it mounts on the throttle body and make sure it is not caked with carbon.

Sep 13, 2009 | 1992 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

scj103

Level 2 Expert

89 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...