Question about GMC Envoy

Open Question

How do I replace my radiator support on my 2006 gmc envoy densely

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 341 Answers

SOURCE: Replace the thermostat on 2002 GMC Envoy

4.2L Engine the thermostat and the neck where the hose goes on is one unit $25 at autozone

  1. Remove the necessary coolant from the radiator.
  2. Remove the alternator, Loosen the outlet hose clamp at the thermostat housing. Remove the outlet hose from the thermostat housing.
  3. Remove the thermostat housing bolts.
  4. Remove the thermostat housing from the engine block.
  5. Clean all of the surfaces of the thermostat housing.
  6. Clean the sealing surface of the engine block.

Posted on Dec 29, 2008

Ad
  • 362 Answers

SOURCE: Fuse Box Location 2006 GMC Envoy

Under the rear seat, drivers side.
Black box you will need to remove the cover.
Lone99star
Please rate this solution.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jason_77a19afa8d604dee

Posted on Feb 10, 2009

  • 101 Answers

SOURCE: 2006 GMC Envoy and the A/C fan wont work in number 5 position

replace the resistor 4 the blower motor that should slove that hope this helps

Posted on Mar 05, 2009

  • 196 Answers

SOURCE: how do you replace tailgate struts on a gmc 2006

There should just be metal clips on each end. Use a thin/standard screwdriver and pry out on the clips. They won't come off completey, but just pop out a little ways. Once they do, just pull and wiggle the strut and it should pop off the ball it's snapped on to. To install the new ones, just make sure the new clips are in the "out" position, snap the socket on to the ball and push in on the clip to secure it in place. Hope this helps.

Posted on Jun 11, 2010

duane_wong
  • 6826 Answers

SOURCE: How do I check and possibly replace the engine oil

Oil Pressure Test Check for proper oil pressure at the sending unit passage with an externally mounted mechanical oil pressure gauge. A tachometer may also be needed, as some specifications may require running the engine at a specific RPM.

  1. While the engine is cold, locate and remove the oil pressure sending unit.
  2. Following the manufacturer's instructions, connect a mechanical oil pressure gauge and, if necessary, a tachometer to the engine.
  3. Start the engine and allow it to idle.
  4. Note and record the oil pressure reading when the engine is cold. The engine may need to run at a specified RPM, if so check the vehicle's specification.
  5. Run the engine until normal operating temperature is reached.
  6. Check the oil pressure reading again with the engine hot and record the value. Turn off the engine.
Compare the hot oil pressure reading to the specification. If the reading is low, check the cold pressure reading against the specification. If the cold pressure is well above the specification, and the hot reading was lower than the specification, the engine may have the wrong viscosity oil. Change the oil, making sure to use the proper grade and quantity, and then repeat the test.
Low oil pressure readings could be attributed to internal component wear, pump related problems, a low oil level, or oil viscosity that is too low. High oil pressure readings could be caused by an overfilled crankcase, too high of an oil viscosity or a faulty pressure relief valve.

Posted on Oct 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need vacuum hose diagram for 2006 4.2 envoy


When the vehicle was built the vacuum hose diagram was on top of the radiator finish panel. If it is no longer there you will have to search for another Envoy and peer at the label on that vehicle.

Jan 29, 2015 | 2006 GMC Envoy 4.2

2 Answers

My 2006 Envoy's air conditioner only blows cold air when the car is moving. What is the problem?


Look to see if the electric radiator fans are working when the A/c is on.

Jul 13, 2014 | 2008 GMC Envoy

1 Answer

How to replacing thermostat 2006 envoy


remove upper radiator hose.. if you trace it back to the engine, you will see the thermostat housing.. should be two bolts.. make sure when you reinstall you clean the surface good, and re applicate with gasket sealer, or gasket..

Jan 25, 2013 | 2006 GMC Envoy

1 Answer

How to-detect a coolant leak 2006 gmc envoy


A shop, or you, could put pressure in the coolant system, then check all over for leaks. Parts stores sell a coolant pressure testing pump- you just place it in the radiator, pump the system up to about 15 psi, then start looking for leaks. The pressure shoould make any leaks quite apparent.

Nov 22, 2012 | 2006 GMC Envoy

1 Answer

I can take the fan and wiggle it up and down. The 2006 Envoy is over heating before I get a mile away from home


cedricponce7, Your fan is connected to your water pump. If you can wiggle it then the bearings in the pump are bad. When the engine is cold open the radiator cap and see if there is any coolant in there. Chances are the radiator is very low. Fill the radiator with water and see if the bottom of the pump leaks. If it does then you have to replace the water pump. Drain the cooling system and refill with the proper coolant. Good luck with this.

Jun 06, 2011 | 2006 GMC Envoy

1 Answer

How do i replace engine air filter on 2006 gmc envoy 4.2 6 cyl? Thanks Bob


Not totaly familiar but on my truck . I follow rubber intake from air box to driver side radiator suport its in a black box there 2 stainless clips open it..

Mar 25, 2011 | GMC Envoy Cars & Trucks

2 Answers

I can't find this car 2006 GMC Envoy SLE 4D owner manual


Its possible that you can find this 2006 GMC Envoy - Owners Manual in the next link: GMC Owners Manual.

Hope helps (remember to rate this).

Oct 01, 2010 | 2006 GMC Envoy

1 Answer

My outdoor temperature indicator is stuck on 0C° GMC Envoy SLE 2006


The temperature sensor is defective, it is located just in front of the radiator, under the radiator support. Before replacing, make sure the electrical connector is seated properly.

Sep 11, 2010 | 2006 GMC Envoy

1 Answer

How do remove the waterpump on a 2006 gmc envoy


1 remove the top radiator cover 7 bolts/clips
2 remove the fanblade and clutch, this will take a large wrench, I believe a 32 mm, and a hammer, the threads are rihgt handed
3 remove the water hoses
4 remove the pump 4 bolts
5 clean all the gasket material off the engine
6 reinstall everything in reverse order
Good luck

Jun 14, 2010 | 2006 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...