Question about Cars & Trucks

1 Answer

Using a 1.1 radiator cap on 3sfe ipsum what happens if I change it with 0.9.the current,1.1 seems to make the car over heat even thought it doesn't boil

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,092 Answers

To.be on safe side use factory 0.9 original specifications.using 1.1 raise boiling point. 0.9 lower boiling point opening pressure 13 psi.use factory specs.to keep from damaging engine.

Posted on Apr 03, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 99 DODGE STRATUS RADIATOR OVERFLOW BOTTLE

Double check that your rad cooling fan is operating as it should, but after that, I'd be looking at a good rad flush, or rad replace. Believe it or not, your heater core is like a small rad, and when you turn the heater on, it actually cools the circulating coolant, slighly,and therefore shows a difference on your gauge. Like I said, make sure the rad fan is coming on when engine temperature is at normal or slightly higher, and if it is, then I'd be taking a close look at my radiator, especially if it wasn't replaced when headgasket was done.

Posted on Aug 27, 2008

  • 231 Answers

SOURCE: 1997 bmw z3 conv. 1.9 overheated, changed

hi jasso, I would recommend checking the water pump if you see no flow in the radiator. Make sure when you fill up the cooling system, that you fill it cold, and that the vent screw in the radiator is loose. fill system until fluid comes out the vent screw. tighten the screw, start the car and have someone run at 1500rpm and check for flow.also, make sure that you have your temp setting full hot and blower on middle speed so that you don't trap air in the heater core.

Posted on Apr 05, 2009

  • 1 Answer

SOURCE: 1989 Mazda B2600i pickup overheats. Replaced

you just said it you need a new fan clutch

Posted on May 12, 2009

Kravcar
  • 192 Answers

SOURCE: Engine overheating in traffic or when idling

I'm assuming your car has the Northstar engine?.

Strangely enough,if you remove the thermostat in the Northstar engine, it will overheat, this is because the stat is both a thermostat and a pressure valve.I can't be bothered to explain in detail how the whole cooling system works but please understand that you need to put the stat back in,(or preferably a new one).As for the cooling fans,what you described is normal for the Northstar.
Further to this, look at my profile,I have provided similar solutions for overheating problems.

Posted on Aug 19, 2009

  • 976 Answers

SOURCE: 1995 Volvo 850 Overheating

head gasket is blown

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota ipsum 3sfe engine 1996 model repair manual


Sorry this site doesn't have this manual on file.

Sep 24, 2016 | Toyota Cars & Trucks

1 Answer

I need to know if the 3sfe engines have a distributor which uses a 4 or 5 pin cap.?


what vehicle does a 3sfe engine fit and how many pistons are there.
the cap will have 4 leads around the outside and 1 in the middle or if the cap has all the leads out the side it will have 2 leads for plugs centre 1 for coil and the next 2 for plugs.

Jun 07, 2015 | Cars & Trucks

1 Answer

Got a gurgling noise every now and then seems to be coming from the engine


Sounds like you may have trapped air in the water system if so needs bled....or the water is going into your overflow tank or back into the radiator...That should happen only when the engine heat is a little higher then normal causing the radiator cap to open and allowing the pressure to push the expanded water into the overflow tank..if you are not experiencing over heating problem then...My bet is your radiator cap is getting weak..have it checked and changed...if necessary.good luck...

Mar 02, 2015 | Cars & Trucks

1 Answer

My Toyota ipsum heats up there is a sound where the timing belt is its like a bearing id faulty can this be the cause of the heating ???


Tension pulley might be the notice but I don't think that would make it run hot..You changed the thermostat and said the water is circulating..If it's not leaking water I would check the Catalytic converter under car...When they start getting clogged up it will make your car run hot because the exhaust can't get out like it supposed to...You can also put a thermostat in that opens sooner

Nov 28, 2017 | Toyota Cars & Trucks

2 Answers

1993 V6 camry engine over heats and check engine light comes on


The thermostat housing is located by grabbing the upper radiator hose, and following it back to the engine block.
The housing that the hose is connected to is the thermostat housing.
Changing the thermostat will fix your problem!

Thanks for using FixYa - a FixYa rating is appreciated!!

Jan 31, 2009 | 1993 Toyota Camry V6

1 Answer

No heat


Hello,
from your description you have an air lock. You stated thermostat changed, I presume you just filled up radiator popped cap on and thought that was it?
Well you need to park on level ground, whilst cold remove cap start engine leave to idle until operating temp, keep clear of coolant filler as hopefully it will gurgle, bubble up and flow over then you need to top up with very warm water and anti freeze.
Wait as it may do it again before settling as the air lock will possibly be in your heater Matrix/Core hence cold air.
Good luck and please remember to rate this effort.
Paul 'W'
Onyer~EDson(:0) {#><U.K.

Jan 18, 2009 | 1996 Ford Taurus

1 Answer

Have a 95 Limina car with 280 000KMs. I changed both head and intake gaskets a few months ago. I`ve also changed the heater core (leaking). Both times the system was flushed and filled. Replaced the...


yes I can help! it seem that you have some air in your cooling system. first you will have to drain the system by removing the lower radiator hose. clamp the radiator hose in place refail the system with 70% cooleant and 20% water. remove the radiator cap and start the engine allow air bubble to escape from the system while the engine is on but do not allow the coolean to over flow from the radiator. replace the radiator cap as soon as you see steam coming from the cooleant. another way is-- you can keep the radiator cap on and loose the bleeder valve that is located on the thermostat side and the other at the back of the engine near the fire wall or crow. Also check the thermostat. make sure it is in the right position and the little opening on the thermostat is not clog and the spring is pointing toward the engine. also make sure that thermostat is right one for your car.

Dec 31, 2008 | 1995 Chevrolet Lumina

3 Answers

Car overheat frequently and at time the engine sound is very loud


Several things can cause this overheating. Have you recently done a:
1. Check Hoses for Leaks
2. Check Radiator for Leaks --- Also, Change Radiator Cap ( can loose pressure there if
cap is bad)
3. Check Water Pump for Leaks. If Water Pump is bad, you will hear a loud noise from it
4 Complete Tune Up? Should be done at least 1x a Yr. Depending on how much you drive the Vehicle. Includes: Plugs, Plug Wires, Gas Filter, Air Breather Filter, PCV Valve, Adjust Timing,
Check Belts -- see if worn
5. Changed your Thermostat & Gasket and have the correct degree Thermostat in the Vehicle?
6.. Had your Radiator Rod and Cleaned out?
7. Temperture Sending Unit (located near Thermostat) could be bad
8. 02-Sensor (Generally located in the Exhaust Manifold - needs a socket with a space in it
to allow the Socket to fit over this top wire of the 0-2 Sensor )
9. Change oil and oil Filter.
10. Change Gas Tank Cap ---

Do all this yearly ( except the Radiator Rod & Clean ( do every 2-3 yrs), and you should not have
any over-heating nor stalling out, etc. and should pass emissions as well.

Nov 25, 2008 | Hyundai Elantra Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

21790 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...