Question about 2003 Pontiac Grand Am

1 Answer

2003 grand am pontac need find where the motor vaccum is to find out why reves are high

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 6,098 Answers

ANY CODES?

Posted on Apr 26, 2019

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
jturcotte
  • 8980 Answers

SOURCE: motor reves up high when started can not keep it

First check to make sure the throttle return springs are closing the throttle. If that's good, the problem is likely a bad idle air control valve/motor. Take the valve out and check for obstructions in the port that could keep the valve from closing. Then, if you have an ohmmeter, you can run these checks on the valve:

    jturcotte_549.gif
    IAC location:
    jturcotte_550.gif
    Remove IAC, check for obstructions in passage, run electrical testsjturcotte_551.gif
    1. Disengage the IAC electrical connector.
    2. Using an ohmmeter, measure the resistance between IAC terminals A and B . Next measure the resistance between terminals C and D .
    3. Verify that the resistance between both sets of IAC terminals is 20-80 ohms. If the resistance is not as specified, the IAC may be faulty.
    4. Measure the resistance between IAC terminals B and C . Next measure the resistance between terminals A and D .
    5. Verify that the resistance between both sets of IAC terminals is infinite. If the resistance is not infinite, the IAC may be faulty.
    6. Also, with a small mirror, inspect IAC air inlet passage and pintle for debris. Clean as necessary, as this can cause IAC malfunction.

Posted on Dec 19, 2010

sodeep
  • 3267 Answers

SOURCE: need picks and location of

There are 4 bolts on the 2.4 Twin Cam cover on top of the engine. I believe they are 13mm. Remove them, and pull the cover up and off. Under there are the spark plugs. And you will see the ignition system connected as one with the cover.

There are no spark plug wires.
You'll find springs inside of insulator 'boots' when you get in there.

see this picsodeep_1.jpg

Posted on Jun 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine Reving high intermittently


first check for vacuum leaks

Dec 08, 2013 | 2003 Ford Escape

1 Answer

When driving truck bogs down when giving it gas.bring when in neutral and rev up the motor to 3grand is snappy like it should be. Wondering if its my tranny


if it reves up to 3 grand when you start it or while in park most likely it is the TPS "throutial Posisition Seneior".

Dec 20, 2010 | 2003 Chevrolet Silverado 1500

2 Answers

Need to change fan motor control switch? Only works on high setting.


this problem is not caused by the switch, it is caused by a defective blower motor speed control resistor, the resistor is located near the blower motor.

Sep 22, 2010 | 2003 Mercury Grand Marquis

1 Answer

Windows problem


I purchased a 2001 Pontiac Grand AM GT in March 2001. Since that time, I have had three windshields, and all the window motors/regulators replaced. Now I need to have the windows repaired again. I have been the only driver of this car, and have less than 69,000 miles. How do you get Pontac to fix this? I cannot afford to replace again, since I am trying am no longer receiving a pay check, and have applied for disability. Thank you, Linda

May 26, 2010 | 2001 Pontiac Montana

1 Answer

Same exact problem.


Could be the plunger motor/ vaccum plunger under the hood. If the cruise light is on, the computer thinks it is working.

Jun 25, 2009 | 2003 Jeep Grand Cherokee

1 Answer

2000 Jeep GC engine reving.


IDLE CONTROL MOTOR. TRY TO CLEAN IT FIRST.REPLACE.

Jan 14, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Grandprix 2003 code P1811 long shifting or hesitating when accelerating


Have a Code P1811 on my 2002 Pontiac Grand Prix. The only thing I have noticed is it gets warm very fast. Haven't noticed any slippage with the tranny...What do I do??

Nov 08, 2008 | 2003 Pontiac Grand Prix

Not finding what you are looking for?
2003 Pontiac Grand Am Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...