Question about Cars & Trucks

1 Answer

Bontrager 300.how to change /reinstall battery on wheel sensor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,041 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear wheel speed sensors on 99 rx 300


this a rear wheel sensor.

Hope this will answer your question,If do pls click on helful botton and you can follow me at fixya,so I can answer your question faster.thanks.
25545694-l3yrohjhb50ijjwrt10tbj0x-5-0.jpg

Mar 10, 2015 | 1999 Lexus RX 300

1 Answer

You answered my question about my 1994 Lexus es 300. I changed out the two sensors. On the transmission. I ohms out the wires and it ohms out .so I changed the gauge cluster an


Check the wheel speed sensor it could be dirty with metal shavings or crusted brake fluid not allowing it to work properly

Oct 28, 2017 | 1994 Lexus Es 300

1 Answer

BAS/ESP lights remained illuminated imediately after changing the battery


Yes, until you reinstall all your codes, this is the reason mobile battery men have a small battery they connect when they change batteries, to prevent this

Jan 05, 2014 | 2005 Chrysler 300

1 Answer

My tire pressure symbol thats pops up but my tires are good


tire monitor system has a sensor in each rim. damage to these senors, or replacement of compete rim and wheels without reinstallation of sensors will cause light to come on. if nothing was changed, possible long life battery in tire senors is bad.

Dec 15, 2012 | 2008 Volkswagen Jetta

1 Answer

2005 chrysler 300c trouble codes p0344, p0016 p0061c


Trouble Code: P0344

Camshaft Position Sensor Circuit Intermittent

Possible Causes:


.Wiring harness fault.5v supply circuit open or shorted to ground.Tone wheel/pulse ring is damaged or corroded.CMP Sensor has failed.CMP Sensor signal circuit is open, shorted to ground or battery. voltage or 5v supply.CMP Sensor ground circuit is open.PCM has failed.Trouble Code: P0016

Crankshaft/Camshaft Timing Misalignment

Possible Causes:


.Base engine problem (i.e., the camshaft timing is not correct).Intermittent condition.CKP or CMP Sensor signal is erratic (check with lab scope).Tone wheel or pulse wheel is damaged or contains debris.CKP or CMP Sensor, harness or connector has failed.PCM has failed.Trouble Code: P0061

Engine Temperature Control Level 2 RPM Performance

Possible Causes:


PCM need to be reprogrammed.PCM has failed.

Oct 27, 2012 | 2005 Chrysler 300

1 Answer

2006, 300 wheel sensors location


TPMI sensors are mounted inside the tire. That's what makes an extra set of wheels for your winter tires so damned expensive.

Sep 28, 2012 | 2006 Chrysler 300 Touring

2 Answers

The VSC and Check engine light turn on for lexus 1999 the cood is p0500


Toyotas and Lexus cars have some unique feaures. If your fuel cap is loose or the O2 sensors on the exhaust are faulty this results in an emission problem and the engine computer unit (ECU) engages the check engine light and disables the VSC (the VSC light comes on to warn you that it has been disabled). However you have p0500 code which says the car has no speed sensor signal. The seed sensor is located on the side of the final drive from the transmission and its job is to measure the speed of rotation of the output shaft. The ECU will compare the signals from this shaft along with the speed sensors in the wheel hubs. If there is a difference between these signals the VSC is engaged to apply braking effort to which ever wheel is slipping (running faster) than the other or that the transmission speed sensor would warrant.
So you either have an emission fault has fed back to the VSC and speed sensor missing (p0500) condition, or you have a faulty sped sensor which has tripped the VSC light and in turn the CEL.
Check your fuel filler cap is on tight, turn radio off and disconnect the negative lead to the battery for 5 minutes (this should clear the ECU memory of the code error). If p0500 error and CEL and VSC lights come back on then check the electrical connection to the speed sensor. Ensure it is clean and making a good contact, check the wiring for continuity. If everything else looks good consider changing the speed sensor.

Sep 14, 2010 | 1999 Lexus ES 300

1 Answer

Do you need to change sensors when you change the break pads (2001 300 es)?


if you are talking about your abs wheel sensors no just make sure you clean everything well

Nov 25, 2009 | 2001 Lexus IS 300

1 Answer

2002 Yukon XL


i serviced my 2004 yukon for abs light came on they told me it was the right front abs speed sensor wire , which is sold sepratly or with wheel hub cost$ 300 or 57$ for just sensor wire, i did all brakes changed sensor and for awhile the stayed off but comes on and at about 20 mph it turns off ?

Jan 25, 2009 | 2002 GMC Yukon XL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22331 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...