Question about Daewoo Matiz

Open Question

Dawoo matiz done clucth cambelt set timing mark Bi but no starting scranks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: cambelt change

went and got a manaul

Posted on Jan 11, 2009

Ad
Hightower971
  • 183 Answers

SOURCE: cam belt timing settings

Clean off the pulley and housing around it and line up the marks, then put the belt on.

Posted on Apr 26, 2009

Rebgagnon
  • 382 Answers

SOURCE: Timing marks for cambelt change

Ej-25 motor has 4 cams. Cam sprockets are marked as follows. Intakes have single hatch mark which point straight up and a double hatch mark that face straight down at double hatch mark on exhaust sprocket. The exhaust sprocket also has a single notch at 90 degrees which points to the outside edge and should line up with mark on cover. Take your time. Hope this helps and have a Great day.

Posted on May 11, 2009

stevenhurc
  • 459 Answers

SOURCE: Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin

these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

Posted on Jun 29, 2009

  • 1757 Answers

SOURCE: toyota 98 camry v6 cambelt timing marks

Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1998 Toyota Camry. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1998/make/toyota/model/camry/1998_toyota_camry_timing_belt_diagram_marks.htm

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My engine is a v6 03 land rover freelander timing mark is like showed in diagram on crankshaft but piston is not tdc


On the freelander it's done that way so none of the pistons strike the valves like when taking the cylinder head off as these pistons come very close to the valves on these engines but if you take off the crankshaft pulley wheel the true mark will be on the gear that the cambelt sits around use this mark on this gear if you want no1 piston at tdc and set the cams up with their irrelevant marks at the same time

Feb 07, 2015 | Land Rover Cars & Trucks

1 Answer

My 2003 freelander crankshaft mark is set as well the cams but piston is not on top dead center on safe mark on sude mark piston is on top but cant turn it gets stuck


I've worked on freelanders loads of times presuming yours is the petrol model when you set the timing up on these when working on them. all pistons are at the halfway mark in the bores this is so no pistons strike the valves when taking the cylinder head off. So the actual mark if you want it set at tdc you need to take off the crankshaft pulley wheel it won't do any harm just four little bolts if I recall when this crankshaft wheel is out of the way you still have the gear there what the cambelt sits round. It is on that gear where the true mark is to set up the timing with no1 piston at tdc. Infact the pulley wheel needs to come off when changing a cambelt make sure the timing marks are set up properly check twice if nessessary then turn engine over one revolution by hand slowly to make sure no internal parts are hitting and timing marks come back together

Feb 07, 2015 | Cars & Trucks

1 Answer

2007 huyndia tucson 2.0 i need the timing marks on exhaust cam and inake cam on the chain


Exhaust camshaft gear and Intake gears have dots on them, chain has colored links. Align colored links to dots or count 14 links from ex cam dot to intake dot. Make sure that the mark on the cambelt side is set first on ex side. Small hole on ex cam gear (cambelt) side to line up with mark on head.

Apr 07, 2014 | 2009 Hyundai Tucson 2.0

1 Answer

Can an engine rev when cambelt is taken off?


Hi

To answer your question directly......NO, the engine can not rev when the cambelt is removed, it won't even start. This is virtually impossible for any 4 stroke engine.

i will explain why....... The cambelt connects your camshaft with your crankshaft, when the engine was assembled, the camshaft and crankshaft was turned on the correct alignment marks and the cambelt was fitted. These marks on the cam and crankshaft allows the 4 strokes to happen at the correct time(intake stroke,compression stroke, power stroke and exhaust stroke) If the cambelt had to be removed, there will be serious damage done to your engine, in the first place, the car will not start if the cambelt was removed. the correlation between your camshaft and crankshaft will not correspond and the pistons will hit and damage the valves.

I hope the above description will help you.

Mar 25, 2013 | 2005 Kia Picanto

1 Answer

I have a dawoo matiz car .790cc year 2000.wich keeps blowing the e.c.m fuse and this cuts off the fuel supply. sometimes it starts ok then suddenly it blows again i checked the fuel pump and seems


Check exactly when you do have a blown fuse as you are driving and in turning or as you driving normally. Also check the wires between E.C.M and Engine. The fuel Supply cuts off surely as soon as the E.C.M Fuse is blown because the fuel supply is going through the E .C. M.

Aug 21, 2012 | Cars & Trucks

1 Answer

Dawoo matiz wont start smells fuely has new leads pops accasionly while turning it over


You have most likely crossed the leads try putting them back on in order, since it occosional pops it tells me you crossed the wires, and if it ran before this then that is your problem, you also could have broken the leads and would need to test with an ohm meter to see if you have.

Jul 06, 2010 | 2001 Daewoo Nubira

1 Answer

How do i set the timing after replacing the cambelt.


Put the engine at TDC compression stroke , Thats when the valves are both closed on No 1 cyl and the piston is on its compression stroke .then align all cam and crank marks. set dizzy on No 1 cylinder (rotor pointing at #1 plug wire) . rotate engine 2 revolutions and recheck all marks. Fire away

Aug 24, 2009 | 1989 Toyota Camry

2 Answers

Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin


these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

May 12, 2009 | 1999 Daewoo Nubira

1 Answer

Can any body help put cambelt back together


You need to rotate the cam until timing marks on the sprocket are in line with the head, then make sure crank shaft timing mark is lined up. Install the belt. Might have to loosen the timing belt tensioner. Put timing belt tensioner back on, rotate the crank shaft with a wrench first to make sure there's no interference. Next, check compression.

Jan 03, 2009 | 1994 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...