Question about 2005 GMC Envoy

Open Question

2005 gmc envoy xl p064d replaced throttle oil sencor accelerator pedal go in to limp mode and now is stall at start

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 401 Answers

SOURCE: how do i get the spare tire from the bottom of the

take your jack handle out from the left rear compartment like 3-4 pieces
join them together
on the right side you will see an acess hole
there is a square end the jack handle fits into then turn the jack handle counter clock wise and the tire will lower
hope this helps

Posted on Nov 13, 2009

Ad

SOURCE: How do you remove the starter off a 2005 GMC Envoy

1st, remove the positive lead to the abttery. Next disconnect the wires from the starter one at a time. I recomment you wrap each with a layer of black electrical tape to protect them. After the wring is removed, remove the bolts to any brackets that are attached to the starter and the two large bolts holding the starter into the transmission housing. Remove the starter. Reverse order to install new starter. Test before your close the hood. It isn't very difficult. If you run into problems, ask me, and I will assist you.

Posted on Apr 07, 2010

  • 1857 Answers

SOURCE: i have a 2003 silverado that gets a reduced engine

So the only other option is to go to mitchell online search mitchell diy

Pay the ten bucks for the wiring diagrams and the testing procedures.

It seems you have addressed all the obvious option. Now you need to diagnose this as per manufacture instructions.

Posted on Apr 11, 2010

  • 201 Answers

SOURCE: 2005 GMC Envoy XL 4x4 4.2l PO172 enigne too rich

Well the first mistake you did was not take it to your GMC car dealer and let them check it out. It could be a computer problem inside the dash somewhere. Hope this helps!?

Please rate solution - Thanks.

Posted on Apr 15, 2010

  • 31 Answers

SOURCE: 2005 GMC Envoy XL High Speed Blower not working

if the other speeds work it is probably the blower resistor; if applies varying resistance to the voltage running the blower; this allows the fan to run at different speeds; should be located very close to the blower motor; behind a panel under the passenger side of the dash

Posted on Jun 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2012 kia soul . Stalled started immediatley. Rpgs would not go up , or over30mph. No check engine light. Or code from dianostic.


May be in limp home mode due to the accelerator pedal position sensor or the electronic throttle body unit .

Dec 03, 2017 | Kia Cars & Trucks

2 Answers

07 trailblazer. replaced the throttle body actuator and still wont come out of limp mode. Rough idle. ???


Code's stored ? APP - Accelerator Pedal Position Sensors Electronic throttle control ! Do yourself a favor an take it to a qualified repair shop .
017 Accelerator Pedal Position Sensors

May 13, 2017 | Chevrolet TrailBlazer Cars & Trucks

4 Answers

What does this mean when engine light with down arrow and loses power


I am only able to shoot you a guess on this and hopefully it steers you the right direction. I believe your vehicle went into limp mode. This can be from over heating to emission problems to a bad piston. The vehicle does this to protect itself. The cheapest way to diagnose this one is to take it in. Remember, having it diagnosed does not mean you cannot fix it yourself. Just pay the fee and take it home if it is something you want to tackle.

Jun 05, 2016 | 2005 GMC Envoy

1 Answer

Using oil looking for possible fix on a 2005 envoy denali


GMC Envoy problems and GMC Envoy repair histories -- car repair descriptions reported ... by car, to see how many repairs each car required and where the car is located. ... 5.3L V8; 2006 291-horsepower 4.2L I6; 2005 275-horsepower 4.2L I6; 2004 ... Advised by OnStar not to drive and have it towed. ----------------------------------------------
galletto 1260

Dec 20, 2012 | 2005 GMC Envoy Denali

1 Answer

No codes, low idle, stubble during acceleration and when A/C is on.


Shotgunning this problem by replacing random parts will only cost you extra money. You need to have a technician diagnose the problem using a high-end scan tool to read the data that the computer is collecting. Also, the fuel pressure needs to be checked.

Jun 14, 2012 | 2003 GMC Envoy

1 Answer

2002 envoy stalled going down road started right back up but had no speedometer wouldnt shift and abs and brake light came on


I had same problem with 2005 Envoy XL 4.2L
After several trips to dealer with "No problem found"....I finally found a technician that determined my ignition switch was intermittently not reading the security chip in the key.
Replaced ignition switch and problem never re-occurred.

Aug 23, 2010 | 2002 GMC Envoy

1 Answer

2006 Envoy stalling when idels and won't stay running


Clean your Throttle body and pay attention to the Idle Air Control (IAC) valve passageway to try to clean the IAC. A dirty or faulty IAC will cause your engine to stall at idle, the job of the IAC is to open the passage way through the throttle body to regulate the amount of air to enter the engine to keep it from stalling when the Envoy is at idle.

Start with the simple and clean the throttle body and inspect any loose or damaged wire leads to the throttle body. Replace or repair any signs of damage.

Thank you for using Fixya and good luck.

Apr 10, 2010 | 2006 GMC Envoy Xl

1 Answer

2005 GMC envoy XL won't start It seems like its not getting gas. I turned the key on and pushed the gas pedal to the floor and nothing it won't start its not the fuel pump its fine


First, do not push the gas pedal at all when starting. There are many things that can cause a no start. A scan tool needs to be hooked up to see if there are any fault codes detected. This problem needs to be diagnosed by a trained mechanic.

Jun 30, 2009 | 2005 GMC Envoy Xl

Not finding what you are looking for?
2005 GMC Envoy Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...