Question about 2011 Ford Focus

Open Question

Torque on knuckle for a ford focus 2011

Torque for all connected bolts to replace the knuckle

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: head bolt torque for a 1996 ford ranger 2.3liter

it is in the haynes repair manuel and chad is right

Posted on Apr 05, 2009

Ad
  • 1392 Answers

SOURCE: head bolt torque spec

Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Posted on Aug 16, 2009

  • 277 Answers

SOURCE: torque wrench settings for ford focus thermostat

There is a set spec, but for the DIY mechanic,,
Using a !/4 " drive, with the correct long socket, apply a FIRM effort on the wrench, but obviously not too much, as to sheer the studs. Always use a NEW gasket on all mating surfaces.
Regards,DT

Posted on Aug 28, 2009

Testimonial: "a specific torque setting would be better !!"

tburtk
  • 158 Answers

SOURCE: torque on 3.0 ford taurus head bolts

40 ftlbs then 73 ftlbs then recheck at 73 ftlbs

Posted on Feb 06, 2010

kirkx
  • 2019 Answers

SOURCE: whats the torque specs on a 2001 ford focus 2.0

You need to buy the manual, because you also need to know the order in which to torque them.
http://www.car-stuff.com/mmparts/ford-focus/repair_manual.html
usually you start at the middle and circle outward.
But they can differ. Some cars you always need to put in new head bolts. Others are done in several stages. This is too critical to take chances on.
If you really can't afford $19 for a manual, go to the library and xerox the pages.

Posted on Feb 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Control arm replace


to replace control arm, you need place jackstands under the frame and lower vechicle so the weight of the vechicle rests on the jackstands and not on the control arms, then remove the front wheel remove ball joint and nut, remove steering knuckle from the lower ball joint using tool KM 507 B. remove control arm to crossmember nut and bolt, remove rear crossmember to body bolt and remove control arm.torque control arm to crossmember nut and bolt 81 ft lbs, torque ball joint to steering knuckle bolt nut 44 ft lbs.torque crossmember to body bolt to 145 ft lbs.

Feb 15, 2012 | 2001 Daewoo Nubira

1 Answer

How do i fix front right ball joint for 2001 mazda protege lx?


SAFELY RAISE SUPPORT FRONT OF VECHICLE ON JACK STAND MAKE SURE VECHICLE PARKED ON SOLID LEVEL GROUND. REMOVE WHEEL OR TIRE. REMOVE BALL JOINT STUD PINCH BOLT AND NUT FROM THE STEERING KNUCKLE.REMOVE BALL JOINT BY PRYING IT FROM THE KNUCKLE.REMOVE BALL JOINT TO LOWER CONTROL ARM BOLT AND NUT. INSTALL NEW BALL JOINT TO LOWER CONTROL ARM.TORQUE THE BOLT TO 86 FT LBS INSTALL BALL JOINT TO THE STEERING KNUCKLE TORQUE BOLT TO 43 FT LBS YOU MORE LIKELY NEED FRONT END REALIGNMENT AFTER THE JOB DONE.

Sep 09, 2011 | Mazda Protege Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

Need help changing balljoints


Found this article for you. Hope this helps

The ball joint is integrated into the lower control arm and cannot be replaced separately.
In many ways, that makes this project a lot less complicated (especially compared to the Taurus / Sable ;))

Before getting started, be sure to get an illustration of the front suspension - the linked Autozone Repair Guide is a good source.

Describing the scene & cast of parts:
  • The control arm connects to the frame with 1 large bolt/nut through a bushing on one end.

  • The other end has the ball joint stud sticking up that connects to the bottom end of the steering knuckle.

  • There's one more part involved: lower arm strut.
  • ** 1996-1998: This 'bar' connects to the middle of the control arm, and angles back and connects to the frame on the other.
    • 1999-2003: the end of the strut connects to the 'extension' coming off the control arm.

Removal Procedures:
Preliminaries: jack the car up, use a jack stand, chock the wheels, take the front wheel off - leave the key in the ignition so the steering wheel is unlocked.
  1. Remove the lower arm strut nut and dished washer from the end that goes through the middle of the control arm.

    NOTE: take notice of which way the dishing of the washer is pointing - you'll want to remember that for reassembly.

  2. Remove the 'pinch' bolt from the bottom of the steering knuckle that holds the ball joint stud in place - punch it all the way out of the knuckle.

  3. To make separating the control arm from the knuckle easier, you can use a small pry bar, or other handy tool to open up the 'pinch' point around the ball joint stud.

  4. I use a good length of 2x2 to leverage the control arm down - separating the ball joint stud from the knuckle.

  5. Last step - remove the control arm-to-frame bolt - and wiggle control arm off the end of the arm strut.

  6. Sit back and have a cup of coffee - 1/2 way there...

Installation:
  1. Put the end of the arm strut through the the control arm connecting point (middle for or control arm extension - model year dependent)

  2. Reattach control arm to frame - torque bolt to 85-97 ft lbs

  3. Ball joint stud to steering knuckle -

    * A second pair of hands really come in handy for this part
    * Line up the stud to the same angle as the opening in the bottom of the steering knuckle
    * I usually reach for the 2x2 to lever the control arm down far enough to get the stud lined-up and back into the steering knuckle

  4. Insert ball joint pinch bolt -

    NOTE: Don't start hammering the bolt back through the hole! There's a groove in the ball joint stud that must be lined up in the bolt hole - may have to tap the control arm up / down to get it "just right". Bolt slides in a whole lot easier then.
    Torque bolt to 46-52 ft lbs

  5. Reinstall strut washer & nut - this is where you were supposed to remember which way the washer 'dishing' was pointing!
    Torque to 85-97 ft lbs
Don't forget to put the wheel back on, and drop the van back to the ground.

Now is the time for the beer... Pricing Price references: Autozone, 1996-1998 $60, 1999-2003 $102

Aug 19, 2010 | 1999 Ford Windstar

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

2 Answers

Had a transmission line pulled off when being towed and need to replace it. Is there any thing I can see to help me?


no, this is one of those situations where you either have the parts to splice it back together or you need to replace the whole line. . Its a dealer part unless you can remove it and go to a autoparts house and match it up.

Aug 03, 2010 | 1995 Buick Riviera

2 Answers

Im trying to replace the rotors and im having a Hard time getting it off. HELP


You might want to spray some WD-40 around the center of the rotor and the wheel lugs. Usually on Honda's, the rotors will have 2 threaded holes to put in bolts. Screw in each bolt equally to help push the rotor away from the hub.

May 12, 2010 | 1995 Honda Accord

1 Answer

How do you replace a rear passenger side torison bar on an oldsmoblie alero 1999


SAFELY RAISE AND SUPPORT REAR OF CAR ON JACK STANDS. REMOVE THE TORSION BAR TO KNUCKLE BOLT WASHER AND BUSHING.REMOVE TORSION BAR TO CHASSIS BOLT.REMOVE BAR FROM THE CHASSIS.TO INSTALL.INSTALL TORSION BAR TO THE CHASSIS TORQUE THE NUT / BOLT TO 48 FT LBS.PLUS ADDITIONAL 120 DEGREE TURN.TORSION BAR TO THE KNUCKLE TORQUE THE BOLT TO 51 FT LBS.

Sep 24, 2009 | 1999 Oldsmobile Alero

1 Answer

Replacing a front wheel bearing


here is a step by step instructions on how to replace your bearing. please copy and paste the link into your browser for an image.

please do not forget to rate and comment about your experience with fixya today.

Removal & Installation
  1. Apply the brakes and hold in place.
  2. Raise the vehicle.
  3. Remove the front tire and wheel assembly.
  4. Remove the cotter pin, lock nut and spring washer from the hub nut.
  5. While the brakes are applied, loosen and remove the hub nut on the end of the driveshaft.
  6. Release the brakes.
  7. Remove the front disc brake caliper and adapter as an assembly, and the brake rotor from the steering knuckle.
  8. Remove the nut attaching the outer tie rod to the steering knuckle. To do this, hold the tie rod end stud with a wrench while loosening and removing the nut with a standard wrench or crowfoot wrench.
  9. Remove the tie rod end from the steering knuckle using Remover, Special Tool MB991113.
  10. Remove the tie rod heat shield.
  11. Remove the nut and pinch bolt clamping the ball joint stud to the steering knuckle.

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during removal. Hold the bolts stationary in the steering knuckles while removing the nuts, then tap the bolts out using a pin punch.
  12. Remove the two bolts attaching the strut to the steering knuckle.

    NOTE Use caution when separating the ball joint stud from the steering knuckle, so the ball joint seal does not get cut.
  13. Separate the ball joint stud from the steering knuckle by prying down on lower control arm and up against the ball joint boss on the steering knuckle.

    NOTE Do not allow the driveshaft to hang by the inner C/V joint; it must be supported to keep the joint from separating during this operation.
  14. Pull the steering knuckle off the driveshaft outer C/V joint splines and remove the steering knuckle.

    NOTE The cartridge type front wheel bearing used on this vehicle is not transferable to the replacement steering knuckle. If the replacement steering knuckle does not come with a wheel bearing, a new bearing must be installed in the steering knuckle. Installation of the new wheel bearing and hub must be done before installing the steering knuckle on the vehicle.
  15. If the wheel bearing and hub need removal. Do not reuse the wheel bearing.
    http://www.chiltonlibrary.com/content/images/32050/images/32050_ptcr_g0035.gif The separation of the ball joint and the knuckle
To install:
  1. Slide the hub of the steering knuckle onto the splines on the driveshaft C/V joint.
  2. Install the steering knuckle onto the ball joint stud aligning the bolt hole in the knuckle boss with the notch formed in the side of the ball joint stud.
  3. Install a new ball joint stud pinch bolt and nut. Tighten the nut to a torque of 70 ft. lbs. (95 Nm).

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during installation. Install the nuts while holding the bolts stationary in the steering knuckle.
  4. Position the lower end of the strut assembly in line with the upper end of the steering knuckle and align the mounting holes . Install the two attaching bolts. The bolts should be installed with so that the nuts face towards the front of the vehicle once installed. Install the nuts. Holding the bolts in place tighten the nuts to a torque of 40 ft. lbs. (53 Nm) plus an additional 90° turn after the specified torque is met.
  5. Place the tie rod heat shield on the steering knuckle arm so that the shield is positioned straight away from the steering gear and tie rod end once installed. Align the hole in the shield with the hole in the steering knuckle arm. Install the outer tie rod ball stud into the hole in the steering knuckle arm. Start the tie rod attaching nut onto the stud. Hold the tie rod end stud with a wrench while tightening the nut with a standard wrench or crowfoot wrench. To fully tighten the nut to specifications, use a crowfoot wrench on a torque wrench to turn the nut, and a wrench on the stud.
  6. Tighten the nut to a torque of 40 ft. lbs. (55 Nm). Install the brake rotor, disc brake caliper and adapter.
  7. Clean all foreign matter from the threads of the driveshaft outer C/V joint. Install the hub nut in the end of the driveshaft and snug it.
  8. Have a helper apply the brakes. With vehicle brakes applied to keep brake rotor and hub from turning, tighten the hub nut to a torque of 180 ft. lbs. (244 Nm)
  9. Install the spring washer, lock nut and cotter pin on the hub nut. Wrap the cotter pin ends tightly around the lock nut.
  10. Install the tire and wheel assembly. Install the wheel mounting nuts and tighten them to a torque of 100 ft. lbs. (135 Nm).
  11. Lower the vehicle.
  12. Set the front toe on the vehicle to required specification.

Apr 17, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
2011 Ford Focus Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...