Question about 1992 Oldsmobile 88

1 Answer

1999 olds 88. I have replaced the fuel pump, sending unit, filter, mass air flow senson, spark plugs and wires, fuel pressure regulator. The car idles fine but when you apply pressure to the gas pedal it bogs down. I also disconnected all of the lines and blew them out. I am at an end what else can I do

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 8,980 Answers

Recommend you check your MAP sensor. You will need a voltmeter.
If you don't have a vacuum gage, just use your mouth to pull a vacuum on the hose and see if the voltage drops when you do.
Let me know if you have questions.


OPERATION The Manifold Absolute Pressure (MAP) sensor, used on 1996-99 vehicles, measures the changes in intake manifold pressure which result from engine load/speed changes, and converts this information to a voltage output. The MAP sensor reading is the opposite of a vacuum gauge reading: when manifold pressure is high, MAP sensor value is high and vacuum is low. A MAP sensor will produce a low output on engine coast-down with a closed throttle while a wide open throttle will produce a high output. The high output is produced because the pressure inside the manifold is the same as outside the manifold, so 100 percent of the outside air pressure is measured.
The MAP sensor is also used to measure barometric pressure under certain conditions, which allows the PCM to automatically adjust for different altitudes.
The MAP sensor changes the 5 volt signal supplied by the PCM, which reads the change and uses the information to control fuel delivery and ignition timing.


TESTING See Figures 1 and 2

  1. Visually check the connector, making sure it is properly connected and that all of its terminals are straight, tight and free of corrosion.
  2. With the ignition ON , check the voltage between terminals A and B (probe the back of the connector to connect to these wires). It should be above 4 volts. Apply 15 in. Hg of vacuum at the MAP vacuum port and check the voltage again. The voltage should be 2 volts now.


1999 olds 88.  I - jturcotte_326.gif

Fig. Fig. 1: Manifold Absolute Pressure (MAP) sensor circuit
When pumping up and releasing the vacuum, check to make sure the voltage readings are smooth. When applying vacuum to the sensor, the change in voltage should happen instantly. A slow change in voltage could point to a faulty sensor.



Fig. Fig. 2: MAP sensor voltage specifications

  1. If the sensor voltage is not within specification, check for a 5 volt reference at terminal C. If the reference signal is found, the sensor is faulty.
  2. If the sensor and circuits are functional, the PCM may be faulty.


REMOVAL & INSTALLATION

3.8L (VIN K) Engine
See Figure 4
On these engines, the MAP sensor is mounted to the PCV valve cover.

  1. Disconnect the negative battery cable.
  2. Detach the MAP sensor electrical connector.
  3. Carefully bend the locking tabs holding the MAP sensor to the PCV valve cover, just enough to remove the MAP sensor.
  4. Pull the MAP sensor straight out of the PCV valve cover.
jturcotte_328.gif

Fig. Fig. 4: On the 3.8L (VIN K) engine, the MAP sensor (1) is mounted in the PCV valve cover (2)

To install:

  1. Make sure that the seal is installed on the MAP sensor and that it is not damaged.
  2. Position and install the MAP sensor to the PCV valve cover. Make sure the locking tabs engage to hold the sensor to the cover.
  3. Attach the sensor electrical connector.
  4. Connect the negative battery cable.

Posted on Nov 27, 2010

  • Andrea Lock
    Andrea Lock Nov 27, 2010

    Hello JT

    I would jut like to inform you that i have read a couple of your solutions, and i am really impressed by the great solutions you manage to post with such a great detail.

    Keep on the good work.

    Kind regards
    Lock123

  • Jeffrey Turcotte
    Jeffrey Turcotte Nov 27, 2010

    Thanks Lock!! I'll have to read some of yours...

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 OLDS 88 TROUBLE STARTING IT, STALLS AT IDLE AND IN DRIVE SOMETIMES IN REVERSE


#1 check fuel pressure after car is running should be 33-38 psi shut off and pressure should hold pressure if it does not then test regulator by removing return line and installing a piece of hose to a container turn key on do not start pressure rises and drops off and container is empty then the fuel pump is bad. fuel in container then regulator is bad. all good then test the mass air flow meter it is in throttle body black in color with 3 wires going to it. located in front of throttle plate tap on plastic cover gently like tapping that annoying service bell at the hotel if engine falters then replace it. good luck.

Jun 19, 2014 | 2006 Chrysler Pacifica

1 Answer

2005 isuzu ascender random misfires code


Po300 codes are system generated caused by computer can not locate real failure condition. Coil on plug engines the coil boots fail and wider gap spark plugs wrong spark plugs by design, secondary ignition wires, vacuum leaks, poor fuel quality, plugged fuel filter, low fuel pressure , leaking pressure regulator, unmetered air between mass air flow sensor and throttle body, crankcase ventilation leak.

Nov 07, 2013 | 2004 Isuzu Ascender

1 Answer

Wont start unless I spray starting fluid into air cleaner. run great after that but if you turn it off you have to use starting fluid again . have put new wires plugs rotor cap distb. capand K&N...


A poor spray pattern in the injectors can cause starting issues. Have you tried a good (read not really cheap) fuel injector cleaner like Chevron Techron or Valvoline Synpower fuel system cleaner? A weak ignition system (worn spark plugs, leaking wires) can cause starting issues. You mentioned that it has a K&N filter on it. These filters use an oil in a cotton media to filter out dirt. Sometimes that oil can get out of the filter and contaminate the mass air-flow sensor. Follow the air tube after the filter box and you'll find a sensor in the tube with several wires running from it. It is made from aluminum and the wire housing is plastic. Remove it from the tube and clean it with a mass air-flow sensor cleaner. You HAVE to use a mass air-flow sensor cleaner specifically made for mass air sensors. Don't use anything else like carb, brake, or throttle body cleaner. Those cleaners will leave a residue on the sensor and just cause you more issues.

As for your fuel pressure, the system pressure with the key on, engine off is 60-66 psi. Do you really think you could visually tell the difference between 60 psi and 40 psi? I know I couldn't. You'll have to use a fuel pressure gauge to verify the pressure. For my money, I think your pressure is low. But, cleaning the MAF is much easier then putting a tester in, and it wouldn't hurt, so I would do that first.

Dec 07, 2011 | 1999 Chevrolet Tahoe

1 Answer

New fuel pump, new cap, plugs and wires, clean air filter. My 98 Jimmy sounds like its missing, it boughs down. Mass air flow regulator? Fuel regulator? Also using a lot of gas lately.


You are right, all of the symptoms are pointing to a fuel pressure regulator. Also try inspecting your vacuum line going to your fuel pressure regulator.
Matt

Jun 24, 2011 | 1998 GMC Jimmy

1 Answer

VERY ROUGH IDLE NO EXCELERATION


Try a few if these ideas...

Priority Action Part Type Cause
1 Inspect Spark Plug Fouled, Damaged, or Broken Spark Plug(s).
2 Inspect Hose (PCV) Clogged or Collapsed PCV Hoses.
3 Inspect Wireset Worn, Damaged or Faulty Spark Plug Wire(s).
4 Inspect Distributor Worn, Damaged or Faulty Distributor.
5 Inspect Catalytic Converter Clogged or Faulty Catalytic Converter.
6 Inspect Fuel Pump Low Fuel Pressure.
7 Inspect TimingSet Slipped TimingChain or Worn TimingGear(s).
8 Inspect Knock Sensor Improperly Connected or Faulty Knock Sensor.
9 Inspect M.A.P. (Manifold Absolute Pressure) Sensor Faulty M.A.P. Sensor.
10 Inspect Throttle Position Sensor Faulty or Incorrectly Connected Throttle Position Sensor.
11 Inspect Mass Air Flow (MAF) Sensor Damaged, Loose, or Faulty Mass Air Flow Sensor or Circuit.
12 Inspect Air Cleaner Temperature Sensor Damaged or Faulty Air Cleaner Tempature Sensor.
13 Inspect Fuel Injector Pressure Regulator Faulty Fuel Injector Pressure Regulator.
14 Inspect Piston Ring Set Worn or Broken Piston Rings.
15 Inspect Timing Specification Incorrect Ignition Timing.
16 Inspect Fuel System Pressure Incorrect Fuel Pressure Being Delivered to Carburetor or Fuel Injection System.
17 Inspect Fuel Filter Clogged or Dirty Fuel Filter.
18 Inspect PCV Valve Plugged or Damaged PCV Valve.
19 Inspect Valve Burned, Worn, or Sticking Exhaust Valves.
20 check idle stop solenoid - if faulty, could cause rough idling
21 inspect distributor cap/rotor - if burnt, could cause loss of acceleration

Apr 18, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

1999 olds alero is sputtering i replaced the plugs and wires its still sputtering i get a po300 code


CODE PO300 MULTIPLE ENGINE MISFIRE DETECTED CONDITIONS. POSSIBLE CAUSES.WEAK FUEL PUMP.STOPPED UP FUEL FILTER.CHECK FUEL PRESSURE SHOULD BE 41 - 47 PSI. THE MASS AIR FLOW SENSOR CONTAMINATED CAUSE VERY LEAN CONDITIONS.EGR VALVE STUCK OPEN OR PVC VALVE HAS VACUUM LEAK. THE EVAP SYSTEM CANISTER FUEL SOAKED.

Mar 12, 2011 | 1999 Oldsmobile Alero

3 Answers

The fuel pump pumps but on start up it dies


Flel regulator will only affect max fuel pressure only will not cause it to not start. try replacing fuel filter first if still does not get fuel then you need to see if it is fuel related or if you have a spark at the spark plugs, pull off a spark plug boot and put screw driver in it hold 1/4 inch away from bare metal and crank engine if you get a spark then it's fuel relateed if no fuel it can be the crank shaft sensor or the cam shaft sensor. let me know if it has fire.

Aug 30, 2009 | 1995 Ford F250

2 Answers

1999 Ford Taurus mechanical problem


Hello,
your problem appears to be the idle control motor located on the air intake manifold it is a small motor that goes bad quite often. Other items that can cause this is a bad /clogged air filter or a tune up (spark plugs and wires), or clogged fuel injectors. to clean the injectors you can buy a container of fuel system cleaner and pour it into the gas tank and as you drive it cleans the system.

Once the fuel system is cleaned via a tankful of cleaner & gas then the idle controller motor would be next on the list to be replaced.

Good Luck !
Rich Lilja

Dec 03, 2008 | 1999 Ford Taurus

1 Answer

I have a 1999 oldsmobile intrigue that is misting a lot. It idels rough, and runs rough. I can still take off it is a little slow, but I can still go pretty fast, but it still mist at the high speeds...


fuel pressure regulator on the fuel rail is probably it or the egr valve is stuck open allowing burnt fuel to flood the intake, im leaning towards the fuel pressure regulator because the o2sensor is probably reading rich or if its reading lean then i would choose the egr valve . good luck

Jul 06, 2008 | 1999 Oldsmobile Intrigue

Not finding what you are looking for?
Cars & Trucks Logo

1,113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...