Question about 2003 Mitsubishi Lancer

Open Question

I've installed the instrument panel with rev counter in my Lancer GL 1990, which actually comes with simple speedometer, water n fuel gauge... I did the jumper wire thing, using the screw behind the rev counter (n to be on a safer side, traced it to rev counter circuit too) but it's still not working... I connected the other end with the negative of distributor... Is it the problem... Plz help me... M dying to c the rev count...

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Instrument panel gauges don't work

I had this same problem with a 2001 mirage. Remove the bezel around the instrument cluster by taking out the two screws at the top out then gently pull. Remove the instrument cluster .Four screws two upper and two lower. Again pull cluster towards you gently. This will unplug the cluster. Once out you will find a very cheap paper type circuit board at the back of the gauges. A trace at the lower middle part of the cluster folded under has cracked right under a plastic clip. I solder in a small wire to by pass the break in the trace, or you can order a new paper circuit board from Mitsubishi part #mr444589 cost about 60.00$

Posted on Nov 22, 2008

Ad
  • 24 Answers

SOURCE: Instument Guages

well the issue is youe enitre gauge cluster i do understand that your speedometer is working but it is a cable speedometer not electronic like everything else in the gauge cluster so first i would recomend checking the voltage getting to your gauge cluster then just replace the guagecluster they are really cheap i a salvage and not hard to install at all but the cluster itself is not very comon to go out so make sure you check voltage to it first i wouldnt want you to go through buying and replaceing the cluster and that not fix it

Posted on Mar 25, 2009

alicantecoli
  • 22484 Answers

SOURCE: I wish to fit an electrical rev counter to my

lots of old cars were + earth but not all .dont think this will make any difference ,is this rev counter for a 6 pot or four?? check terminals on back of unit??does one look as though it the earth ?? if not then one goes to earth and the other goes to the points side of the coil.easy

Posted on Apr 11, 2009

  • 150 Answers

SOURCE: lancer gl 2004

You will need to replace the timing belt and the balance shaft belt (if applicable). Your car may not have a balance shaft belt. Mitsubishi did away with that belt, but I can't remember what year it started. At 60,000 miles. And again at every 60,000 miles. You should also replace the accy drive belts at that time. If you don't replace the timing belt and it breaks, severe engine damage WILL happen. Hope this helps. Good luck.

Posted on Jun 20, 2009

  • 7 Answers

SOURCE: 99 lancer,speedo tacho n gauge problem.

probably burnt or cracked circuit board on back of gauge cluster

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 3.2 DI-D GLS SWB Auto 4x4 and have a problem which started suddenly 2 days ago. None of the instruments come on when switching the ignition key. I have checked the fuse #2 and it is not


Your problem may be in the ignition switch. There is a lot of stuff going on when you turn the key. There is an actuator in the ignition. Normally the car won't turn over when they go bad, but I can't know everything!!!!

Jan 01, 2015 | Cars & Trucks

1 Answer

Electrical failure of instruments (temp & fuel gauges, speedometer & rev counter) on 52reg ford focus. All fuses intact. What's the problem?


Check the temp sensor wire that goes to the engine. They will short out to engine and make the dash do strange things.

Nov 07, 2010 | 2003 Ford Focus

2 Answers

Speedometer stopped working.


The speed sensors will not fix it. This is something that these cars will do in hot weather. The instrument cluster need to be removed and the contacts from the printed circuit to the connector need to be cleaned. Over time they will lose contact and affect the fuel gauge or speedometer. You may have to replace the speedo cluster. Sometimes if you hit the dash just above the fuel gauge it will start working too. Been there done that, fixed mine as the printed circuit was coming apart at the harness connector.

Jun 03, 2010 | 1990 Buick LeSabre

1 Answer

My fuel gauge rev counter speedometer and temperature gauge needles are not workin


I'm dealing with the same issues on mine: check the speedo cable is properly hooked up on the back of the instrument panel and at the sender on the transmission. Check your electrical connections and fuses are ok for all the other instruments.

Jan 04, 2010 | Fiat Strada Cars & Trucks

1 Answer

Just bought a used 1995 Honda Prelude and the Tach and speedometer work along with the clock but I can't see any other gauges. (Gas, oil, temp and whatever else might be there. What is the problem?


Since you just bought the car, I thought that you might not be aware of the instrument lighting control. I apologize if you know this:
The dial on the dashboard to the left of the instrument panel controls the brightness of the instrument panel lights. Turn the dial to adjust the brightness.
To reduce glare at night, the fuel and temperature gauges dim when you turn on the parking lights or headlights. You then adjust their brightness when you adjust the instrument panel brightness. Turn the dial up as far as it will go to return the fuel and temperature gauges to their daytime brightness.
Hope it's that simple.

Nov 25, 2009 | 1995 Honda Prelude

1 Answer

Back lights are dim on speedometer, odometer


You probably checked this, but sometimes we forget.
The dial on the dashboard to the left of the instrument panel controls the brightness of the instrument panel lights. Turn the dial to adjust the brightness. Also, to reduce glare at night, the fuel and temperature gauges dim when you turn on the parking lights or headlights. You then adjust their brightness when you adjust the instrument panel brightness.
Turn the dial up as far as it will go to return the fuel and temperature gauges to their daytime brightness.
I hope helps and it's that simple for you.

Nov 03, 2009 | 1996 Honda Prelude

2 Answers

Instrument panel on my vauxhall astra does not work


i think vauxhall used the canbust system on this car and you cant cut into the wiring m8 you can buy a repair kit from internet but it might be expensive

Sep 04, 2009 | 2003 Hummer H2

2 Answers

My instrument panel dashboard lights are out how do i fix them?


can ne 1 please help me, i disconnected my battery and then when i connected it again i noticed that my instrument panel was not lit up nor is my heater dials or my rev counter how do i fix this please please

May 04, 2009 | Chevrolet Beretta Cars & Trucks

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...