Question about 2003 Mitsubishi Lancer

Open Question

I have a 2003 mitsubishi lancer automatic. The speedometer and odometer will not work. I had to wash the engine before this happened can anyone help me fix this problem. I replaced output speed sensor still nothing. does the computer have a protect mode that I need to reset. Thanks Eric

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: 2003 Mitsubishi Lancer

so u have a CH/CG lancer

you would need to remove the two 10mm bolts from the coil packs and leads and then stick the smaller version of spark plug socket in remove them, bear in mind if u have a mivec motor the spark plugs MUST be Platinum :)

Posted on Jan 02, 2009

Ad
  • 2 Answers

SOURCE: Ford Escort Odometer Not Working

these can also be caused by a bad alternator

Posted on Jan 09, 2009

  • 1 Answer

SOURCE: WHERE IS THE CAMSHAFT POSITION SENSOR ON A MITSUBISHI LANCER ES

It is right underneath your air cleaner.

Posted on Jan 15, 2009

  • 26 Answers

SOURCE: 1995 honda accord speedometer and odometer not working

Sounds like either your speedometer cable, your nylon gear on the side of the tranny where the cable ties in, or the odometer itself is shot. One of those three will set you straight. If you are able, remove the cluster, take the cable off the back, and pull it out of the sheath. You will see if its broken or not from there. If not, slide it back into the sheath, then you have to find out where the sheath meets the tranny, and pull it off of there. Then, you can get someone else to watch the speedo as you turn the cable from the bottom. If it works, great, if not, then its your cluster/odometer/speedo. If it does work, the small gear in the transmission is shot.

Posted on Feb 14, 2009

Molson02536
  • 3854 Answers

SOURCE: Speedometer/odometer/cruise control isn't working.

It's your speed sensor at the transfercase on the drivers side i believe. Check the wire and clip to the sensor for any break or loose contacts. 
Easy fix and is about a 30 min job to do with simple tools. Un-clip the wire conntection, remove the retainer bolt and slide and sensor out. To install just do everything in reverse and add transmisson oil if needed.

Most of the time, it's going to be the sensor. Keep in mind that there are two sensor's so make sure it's the one on the output shaft at the transfercase. The other one is closer to the front of the transmission on the same side with is the input Volosity speed sensor.
If it was your ABS sensor, you ABS light would come on in your dash.
Good luck and hope this helps

Posted on Apr 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install need diagram of timing belt replacement


2003 Mitsubishi Lancer 2.0L MFI 4cyl

zjlimited_403.jpg

Fig. Accessory drive belt routing-1.8L, 2.0L (SOHC), and 2.4L (4G69) engines


zjlimited_404.jpg

Fig. Accessory drive belt routing-2.0L (DOHC) engine




zjlimited_405.jpg



Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines


Hope helps (remember to rate this ansswewr).

Jan 05, 2011 | 2003 Mitsubishi Lancer

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

2 Answers

Problems with lancer MR speedo revs and odometer


exact same problem happened with my lancer i took it to an auto instrument shop and it cost me $330 to fix and hasnt stopped working since.

Oct 14, 2009 | 2003 Mitsubishi Lancer

2 Answers

I have 03 lancer es with a code of po506 any suggestions


There may be a vacuum leak; an restriction in the intake or exhaust; faulty PCV valve; bad or dirty throttle body; internal engine problem; or a failed PCM
This code is usually triggered on vehicles with electronic throttle controls instead of throttle cables. This code is more of an informational code and there should be other codes that show up to narrow down what the issue is

Sep 14, 2009 | 2003 Mitsubishi Lancer

1 Answer

Speedometer, odometer frozen


there is a steel braided cable located at the back of your speedo panel that connects it to the tranny, this cable rotates from the point it connects to the tranny and transmits it to your panel. this cable may have snapped. pull out the panel, take out the cable and replace.

Sep 02, 2009 | 2003 Mitsubishi Lancer

2 Answers

Gauges all Dead


i think that u have a problem with RPM cause this problem is not always being with ur car.

Jun 06, 2009 | 2003 Mitsubishi Lancer

1 Answer

2003 Mitsubishi lancer es


I has this problem after i had recently changed out the stereo. Chech to see if the illumination wire that runs to the stereo is hooked up correctly. If you have an aftermarket stereo you may need to ground it to the body of the car.

I believe that the fuse is located in the engine compartment but check your car manual to find the exact location.

Aug 21, 2008 | 2003 Mitsubishi Lancer

3 Answers

1997 CE Lancer speedometer


i had the same problem on my g/f's 2000 lancer GLXi, (with tacho),
i fixed the problem by putting a jump wire on the back of the instrument cluster,
the fault was in the wiring to the tacho part & i drew up my own wiring diagrams for the cluster unit,
then traced the fault,
looking @ the back of the cluster unit, the top right hand screw for the speedometer,,, follow the track on the circuit-board, there is a link wire UNDER the board (there is a dotted line on top where it goes, i think its the left 1,,, there is 2) this track then goes to the bottom left screw on the tacho,,,
i soldered a small gauge wire from the bottom of the link solder joint (MAKE SURE ITS THE CORRECT LINK, THERE IS 2 SIDE BY SIDE) to the bottom right track on the vertical plug socket (its common pos for the warning lights) this is where the "MIRAGE" & other "CE LANCER" (without tacho) gets its speedometer & gauges power from,

kind regards waz
if anyone needs a photo i will pull out the dash again lol its only 6 screws

Jul 17, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...