Question about 2002 Ford E350

2 Answers

I have a 2002 V10 ford chassis motorhome. Took it in to have exhaust manifold bolts replaced. Now will not start. No fuel. You can hear the fuel pump running but when cas line opened at inline filter under chassis very little trickle of gas comes out. Could the pump be running and not pumping or is there a filter prior to the pump in the fuel tank that is causing the problem??? Never had any sign of this problem till now.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,431 Answers

Yes it can run and produce low pressure, There is a non service filter in the tank that is part of thefuel pump, if the pressure is low a replacement is the fix for you

Posted on Jun 04, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 752 Answers

There is a strainer filter attached to the fuel pump in the tank however you really need to see how much gas is actually in your tank first. Sounds like a fuel line may be pinched.

Posted on Jun 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a motorhome 2002 V10 Ford Triton engine that is not starting. Engine turns over but it won't start, not getting fuel. Supposedly there is a fuel switch for the fuel pump. Does anyone know location


If it has an inertia switch, it should be on the passenger side near the door.
I would first check the pump relay to see if it is sending power to the pump thru the switch. And do you have a switch for dual tanks ?

Feb 16, 2014 | 2000 Ford F350 Super Duty Super Cab

1 Answer

2002 ford f 350 V10 cranks but will not start


Does the vehicle has a PATS - anti-theft system ? red light flashing on top of the instrument panel when trying to start ? Fuel pump relay is energized by the PCM - engine computer if no anti-theft system problems . Do you know how to test automotive electrical circuits using a wiring diagram an a DVOM - digital volt ohm meter ? Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info Year , make , model an engine . Under system click on engine then under subsystem click on fuel controls . Click the search button then the blue link. Scroll down to the #8 diagram . Watch these videos
Testing Electric Fuel Pump Problems with Voltage Drop Test
Fuel Pump Electrical Circuits Description and Operation

Feb 09, 2018 | 2003 Ford F350 Super Duty DRW SuperCab

2 Answers

Ford 460 loses power then dies. Starts back up. Idles fine.


It sounds like you might have a clogged catalatic converter on the exhaust system.

Apr 23, 2010 | 1999 Ford Super Duty F 450

1 Answer

How do i change a water pump in a 97 grand am with a 2.4 litre engine


2.4L Engine
See Figure 3
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Disconnect the oxygen sensor wiring.
  4. Remove the upper exhaust manifold heat shield.
  5. Raise and safely support the front end of the vehicle securely on jackstands.
  6. Remove the exhaust manifold brace bolt.
  7. Unbolt and remove the lower exhaust manifold heat shield.
  8. Break loose the manifold-to-exhaust pipe spring loaded nuts.
  9. Unbolt the radiator outlet pipe assembly from the water pump cover.
  10. Disconnect the exhaust pipe from the manifold.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
Do not rotate the flex coupling more than 4°. this could damage the component.
  1. Separate the radiator outlet pipe from the oil pan and transaxle.
    1. On manual transaxle, remove the exhaust manifold brace.

  2. Next, leave the lower radiator hose attached and pull down on the outlet pipe to detach it from the water pump. Allow the outlet pipe to hang.
  3. Lower the vehicle.
  4. Remove the exhaust manifold-to-cylinder head nuts.
  5. Extract the manifold, seals and gaskets.
  6. Remove the timing chain cover. Refer to the procedure later on in this section.
  7. Remove the timing chain tensioner. Refer to Timing Chain removal later in this section.
  8. Unbolt the water pump from the cylinder block.
  9. Extract the pump assembly-to-timing chain housing nuts.
  10. Remove the water pump and cover assembly.
  11. Separate the pump from the cover.
  12. Clean all mating surfaces of gaskets and sealant materials.

To install:
Prior to installing the water pump, read the entire procedure. Pay special attention to the tightening sequence to avoid component damage and ensure a proper seal.
  1. Attach the water pump to the cover and hand-tighten the components.
  2. Lubricate the splines of the water pump drive with chassis grease or equivalent, then install the pump and cover assembly. Hand tighten the cover-to-block bolts.
  3. Install the pump-to-chain housing nuts and hand-tighten.
  4. Lubricate the O-ring on the radiator outlet pipe with an anti-freeze solution and slide the pipe into the water pump cover, install and hand-tighten the bolts.
  5. With the specified gaps, tighten in sequence as follows:
    1. Pump assembly-to-chain housing nuts
    2. Pump cover-to-pump assembly
    3. Cover-to-block, bottom bolt first
    4. Radiator outlet pipe assembly-to-cover

  6. Install the exhaust manifold using new gaskets.
  7. Install the manifold-to-cylinder head nuts, follow the tightening sequence and tighten to specifications.
  8. Raise and support the front of the vehicle.
  9. Index the exhaust manifold-to-exhaust pipe flange bolts.
    1. Turn bolt bolts in evenly to avoid cocking the exhaust pipe and binding the bolts. Turn the bolts in until they are fully seated.

  10. Install and secure the radiator outlet pipe to the transaxle and oil pan.

On manual transaxles, install the exhaust manifold brace.
  1. Install the timing chain tensioner and chain cover.
  2. Attach the lower heat shield.
  3. Lower the vehicle.
  4. Attach the exhaust manifold brace. Tighten the manifold-to-exhaust pipe nuts to specification.
  5. Attach and secure the upper heat shield.
  6. Connect the oxygen sensor wiring.
  7. Fill the radiator with coolant water mixture until it reaches the heater hose coolant outlet, then install the hose and continue to fill. This will assist with the complete cylinder block fill.
  8. Connect the negative battery cable.
  9. Start the engine and top off the cooling system and check for leaks.
ec6ae2e.jpg

Dec 28, 2009 | 1997 Pontiac Grand Am

1 Answer

My ford v10 engines hesitates under load. It


1 Ignition system not operating properly
2 Dirtyor clogged fuel injector(s).
3 Low fuel pressure. Check for proper operation of the fuel pump and for restrictions in the fuel filter and lines.
4 Fuel injectionor engine control systems malfunction.
5 Vacuum leak at the intake manifold or vacuum hoses.
6 Restricted air filter.
7 Fuel pump or pressure regulator defective.

Dec 19, 2009 | 2000 Ford Excursion

2 Answers

Need the step by step instructions and pictures on how to replace an water pump on an 2002 Oldsmobile Alero 2.4L


Removal & Installation

2.2L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Exhaust manifold, if equipped with n automatic transaxle Right front wheel Splash shield Water pump sprocket access plate from the timing cover

    fcd00e0.jpg

    Fig. Remove the water pump sprocket access plate from the timing cover -2.2L engine
  5. Attach Water Pump Sprocket Holding Tool J 43651to the sprocket using the access plate bolts to secure the tool to the engine front cover.
    Sprocket to water pump bolts Engine block to water pump bolt Engine front cover to water pump bolt Thermostat housing to water pump feed pipe 2 water pump to engine block bolts Water pump

    30965cd.jpg

    Fig. Water pump mounting-2.2L engine
To install:
  1. Use a threaded stud in the water pump hub to align the hub to the water pump sprocket.
    Water pump and bolts Thermostat housing to water pump feed pipe Engine front cover bolt and engine block to water pump bolt. Tighten the bolts to 15 ft. lbs. (20 Nm) 2 of the water pump sprocket to water pump bolts
  2. Remove the threaded stud.
    Last water pump sprocket to water pump bolt and tighten the sprocket bolts to 89 inch lbs. (10 Nm).
  3. Remove the tool.
    Water pump sprocket access plate to the timing cover and tighten the bolts to 89 inch lbs. (10 Nm) Splash shield Right front wheel Exhaust manifold, if removed
  4. Fill the cooling system.
  5. Connect the negative battery cable.
2.4L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    WARNING Do not rotate the flex coupling more than 4 degrees or damage may occur. Oxygen Sensor (O 2 S) electrical connector Exhaust manifold heat shield Coolant inlet housing bolt through the exhaust manifold Exhaust manifold brace-to-manifold bolt Manifold-to-exhaust pipe studs Coolant inlet housing-to-water pump cover bolt Exhaust pipe from the exhaust manifold by pulling it downward Coolant inlet pipe from the oil pan Brake vacuum pipe from the camshaft housing Exhaust manifold from the cylinder head Heater hose from the heater outlet pipe Timing chain cover and tensioner Water pump cover-to-engine bolts 3 water pump-to-timing chain housing nuts Water pump and cover assembly Water pump cover from the pump

    f9cdfa8.jpg

    Fig. Exploded view of the water pump mounting-2.4L engine
continue...

Oct 22, 2009 | 2002 Oldsmobile Alero

1 Answer

1987 Fleetwood 26C motorhome is on a Ford E350 Starting Problem


if it was me i would start with a new fuel filter and some STP gas treatment if you let it sit for a long time there maybe water in the gas tank and try these websites to see if they have your motorhome listed its www.autozone.com and the other one is www.alladtadiy.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your motor home

Jun 07, 2009 | Ford E-350 Cars & Trucks

2 Answers

How to replace the water pump on 1993 oldsmoblie achieva.


2.4 enigine is the harder of the 3 enignes. it will need a timing chain to be removed and a coolant tube in the back of the engine to be removed. this job on the book calls for almost 7 hours.

if its 3.3 or 3100 its alot easier.

3100 is just 4 10mm pulley bolts and 5 or 6 small 8mm water pump bolts.

3.3 is alittle more work, but same concept as 3100 engine. more owkr only cause its in a tighter area.

good luck,
michael

Apr 29, 2009 | Oldsmobile Achieva Cars & Trucks

2 Answers

Fuel pump does not work- 1999 ford super duty class a motorhome


Check your vehicles safeties. Your ECM is probably programed for engine shutdown if it senses low oil pressure or low coolant level. Do a preliminary check.

Apr 28, 2009 | 1999 Ford Super Duty F 550

4 Answers

Static throttle misfire


Possible bad fuel pump or fuel pump relay.

Dec 03, 2008 | 1994 Ford F350 Crew Cab

Not finding what you are looking for?
2002 Ford E350 Logo

386 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...