Question about 2003 Mitsubishi Lancer

1 Answer

2003 Mitsubishi Lancer es question cant figure out

2003 Mitsubishi Lancer es question cant figure out where the inlet heater hose is located. need to find it for my flush kit.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 383 Answers

Unfortunately, I do not think you will be able to use the flush kit on your car. There are two lines with very short hoses. The one you are looking for is only a few inches long. SORRY.

Posted on Jun 16, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Mt car blows cold air but not hot i replace the thermostat and added antifreeze but it still no hot air its for a Mitsubishi lancer 2003


there are two hoses than run through the firewall to the heater core. With the car fully warmed up those two hoses should be about the same temp. If one is hot and one is significantly cooler that the heater core is likely plugged. The hoses can be removed and the heater core can be backflushed with a garden hose. do this several times alternating between the inlet and outlet of the heater core. reconnect the hoses and see what happens. Worse case scenerio you'll need to replace the heater core.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Nov 29, 2015 | Mitsubishi Cars & Trucks

2 Answers

Where is the inlet heater hose located on a 2005 Hyundai Elantra?


You wouldn't even be able to see it from this angle. It will be on the firewall. There will be two hoses (rubber) next to each other that are the same size. They are likely 5/8" hoses. The inlet is typically on the passenger side. Make sure the hoses are rubber. The A/C lines run into the firewall near that area but they are metal.

Dec 29, 2014 | 2005 Hyundai Elantra

1 Answer

Im trying to flush the cooling system on a '97


Not positive about that engine, but the usual method is the heater inlet will come off the cylinder head somewhere and to the firewall, and the heater outlet (the return hose) will be at same place on the firewall and go to the water pump, very close or at the fitting where the lower radiator hose attaches to the water pump inlet.

Jul 21, 2013 | Cars & Trucks

1 Answer

Need help finding inlet heater hose from fire wall to engine


The inlet going TO the heater core should be the top one (I think) but in any case it would be the one with the heater control valve on it (see picture below) Hope this is what you were looking for....

3_5_2012_4_38_32_pm.jpg

Mar 05, 2012 | 1998 Lexus ES 300

1 Answer

I'm installing a Prestone coolant flush kit and need to find the heater inlet hose. Which one is it?


with the engine running it is the hottest one, it is also the largest of the 2 small heater core hoses going to the firewall from the engine.

Aug 21, 2010 | 2003 Oldsmobile Silhouette

2 Answers

How to drain and flush radiator


at the bottem on the left or the side there is a small key like screw ( righty tighty lefty lucy } then u must remove the radiator cap and also remove the themastate be sure to attach the therma housing and hose and unatch it at the top of the radiator the put water hose in the open cap area and flush for 20 mins turn on engine and let run for 2 min and repeat flushing untill all antifrez desapears. be sure to put every back tack pitchures as you remove so to put back the same way it might be good to get new thermastate

Jun 25, 2010 | 1998 Ford Taurus

1 Answer

2004 Mitsubishi lancer es stop light switch


the brake lighr switch located : the top of the brake pedal.

May 04, 2010 | 2004 Mitsubishi Lancer

1 Answer

WHERE IS THE FUEL FILTER ON A 2003 MITSHBISHI LANCER ES ENGINE 2.0


The fuel filter/strainer is part of the fuel pump assembly located in the gas tank for the Mitsubishi 2.0L

Dec 04, 2008 | 2003 Mitsubishi Lancer

1 Answer

FUEL FILTER


Most modern day fuel injected cars have the pump located inside the gas tank. It's the safest place to put it, it can't ignite any fumes because it's submerged in the liquid.

Dec 04, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

Related Topics:

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...