Do you get anything at the push button? Might be worth checking the condition of the battery, the starter solenoid, the main fuse and the starter itself as this sounds like an electrical issue. See if you can get the battery tested 'under load' as the cold can make old batteries sluggish.
which i need to make faster. I have been looking at the peugeot jetforce moped which has a supercharger would it be possible to put a supercharger on mine?no chance....not unless its built for one....get better parts the supercharger wont do you any good. get a better exaughst,chain,gears,etc,,,
I am a Harley guy, but your bike might have a BAC sensor, it is made to shut the fuel off if you tip the bike. Simple test, is to get to the air breather, crack the throttle, use a spray bottle spray so gas in the breather inlet. Then try to start it, if if starts and runs just a bit and dies, it means you are not getting fuel and the is a sensor somewhere.
I've been told that if you disconnect the battery for 30 min. then reconnect, it coould reset it.
I hope this at least gives you a direction.
hi,i dont know why you would have to drain a battery but however,you have effectively flattened it by draining the electrolite out,DO NOT TRY AND CHARGE IT,IT WILL EXPLODE, the only thing you can do now is take the battery to an auto electrician have it refilled and recharged(if it still usable)if it is not still usable then you will be in for a new one,hope this helps
Hi, Heidiyoung26 before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. What To Do If Your Motorcycle Doesn Start 3 Things to Look for When Your Motorcycle Won Start The Allstate Blog http://www.banici.pl/bam/Tom/GV125/Instrukcje/GV125_SERVICE_MANUAL_EN.pdf https://alpha-sports.com/hyosung_parts.htm http://www.family-motorsports.net/GY6-50cc-150cc.pdf https://absolutelyscooters.net/pdf/CGEN_dawg_scooter_manual.pdf
Hi, Kalliope before testing any electrical component in the Turn Signal Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, "AGM" batteries fall into this category more so than lead-acid types, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If no turn signals are working the cause could be a faulty turn signal module/flasher or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If your turn signal comes on but takes several seconds before it starts flashing you may have dirty contacts in the turn signal switch/button, the switch needs to be opened up and cleaned also the flasher may be starting to fail. It should be noted that cold weather will only exacerbate the situation especially when temperatures drop down below freezing and the location of the component, turn signal switches on the handlebar are at the mercy of the oncoming freezing 70 mph wind and makes it hard for the contacts to do their job covered in frozen grease/grime
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first, look for, corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. https://safer-turn.com/smart-turn-system https://www.youtube.com/watch?v=zRJFz_O8FTI https://www.manualslib.com/brand/hyosung https://alpha-sports.com/hyosung_parts.htm http://mybikemanuals.com/hyosung
Hi, Anonymous before testing any electrical component in the Charging System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
2. To check the regulator unplug it from the stator. Take a test light and clip it to the negative terminal of the battery and then touch first one pin and then the other on the plug that goes to the regulator. If you get even the slightest amount of light from the test light the regulator is toast.
To do this with a meter: black lead to battery ground, red lead to each pin on the plug, start with the voltage scale higher than 12vdc and move voltage scale down in steps for each pin. Any voltage is a bad regulator.
3. On the other part of the disconnected regulator plug. Set the multimeter for Ohms x1 scale and measure for resistance across the pins of the stator. You should read something around 0.1 to 0.2 ohms for a 32 amp system.
4. Then check for continuity between each pin on the plug and frame/engine ground. The meter needle should not move (infinite resistance)(digitals will show infinite resistance) if the meter needle does move (indicating continuity)(digitals will show some resistance), recheck very carefully. If the meter still shows continuity to ground the stator is shorted (bad).
5. Set the meter to read A/C volts higher than 30 volts (the scale setting for voltage should always be higher than the highest voltage you expect or you may fry the meter). Start the bike, and measure from one pin to the other on the plug (DO NOT cross the multimeter probes! - touch them to each other). You should read roughly 16-20 vac per 1,000 rpm.
6. If the battery was good under load test, if the stator is NOT shorted to ground, and the stator is putting out A/C voltage, then the regulator is bad (most likely even if passed step 2)
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. http://korider.com/index.php?topic=25724.0 How to Fully Troubleshoot Your Motorcycles Charging System MotorcycleMD https://www.manualslib.com/brand/hyosung https://alpha-sports.com/hyosung_parts.htm http://mybikemanuals.com/hyosung