Question about Zongshen 985 C3 V4 Motorcycles

2 Answers

I have no spark on a sunl 250 4 wheeler i have replaced coil,voltage regulator,and cdi box?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 70 Answers

If you have replaced all that it sounds like it is the stator. its an alternator for small engines. get one on ebay cause factory are always expensive. its located behind the pull start. take that off then the side case cover.

Posted on Jul 09, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hey mate I'd start by bridging all your kik switches n interlocks before buying a stator

Posted on Jul 22, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my 97 Honda 4 wheeler not getting fire


There are three items that are connected together needed to create spark on your 1997 Honda 4-wheeler, regardless of which model it is.
Before we go through a checklist of these three important parts, look for a black wire with a white stripe that runs to the ignition switch and kill button from the CDI box. Disconnect this wire before it gets to the ignition switch and kill button, then check for spark. The most likely cause is a broken kill switch on the handlebar, or shorted ignition switch. Such a condition grounds this wire and kills the spark.
If this test did not restore the spark, continue reading...
Here is what is required to create a spark.

First, the alternator has one coil which generates a high voltage--about 125 Volts AC for the CDI ignitor box.

Second, there is a pulse voltage generated once every revolution of the engine that goes to the CDI box. This pulse causes the CDI to dump its stored energy from the 125 volt line into the primary of the ignition coil.

Third, If the two connections of the wire that runs from the CDI to the Coil are BOTH SHINY clean, the ignition coil will generate a spark.

If any one of these 3 don't happen, the spark will go away. Of these three, item 3 -- one or two tarnished and/or dirty connectors -- is the most likely cause. Just an added resistance of 0.3 Ohms or more in the CDI to Coil connections will cause the ignition to fail. No other wires have to be this clean.

Sep 26, 2014 | Motorcycles

1 Answer

No spark but motor turns over on 1987 honda fourtrax 250


possibly the rectifier faulty or stator coil

Sep 04, 2014 | Motorcycles

1 Answer

No spark at the plugs


the things i would check are the pickup coil, the ignition coil, cdi box, the ignition switch and the kill switch. I just purchased a 4 wheeler that they changed everything electrical on it. come to find out the kill switch was melted onto the muffler causing it to be always activated. if you get a repair manual or look hard on the internet you can get the proper readings to ohm test your pickup coil, ignition coil and cdi box. the ignition switch can be tested with a test light and the kill switch should not be grounded unless activated. (hook a test light up to the positive side of the battery and then touch the kill switch wire. if it lights up there when not in the kill position you have a problem)

Jun 05, 2014 | 2004 Honda CMX 250 Rebel

3 Answers

My Rm 250 wont spark need to know the volts from stator to cdi plug. Got brand new cdi, stator , rotor and pick up coil but it still wont spark.


The Voltage From The Stator To The CDI Should Be Around 40 Volts(AC) At Cranking Speed. Be Sure Your Meter Is Set For (AC) Not (DC). The CDI Changes The (AC) Input Voltage To (DC) Output Voltage To The Primary Terminal At The Coil. An Electrical Shock Hazard Exist If Stator Voltage Is Checked With Engine Running. Always Perform This Test At Cranking Speed (R.P.M.) For SAFETY. 120 Volts (AC) Can Be Present With Engine Running.

May 22, 2011 | 2003 Suzuki RM 250

2 Answers

Hi,i have a sunl slu-6k,its not getting any fire.I have changed the coil,stator,cdi,key switch,voltage regulator and the wiring harness.Can you give me some help with this because im lost. thanks steve


Chances are it is a grounded kill switch on the handlebars or a side-stand / center-stand kill switch that has gone bad or is out of position.
Stick in a new spark plug also.

Sep 13, 2009 | 2005 Kymco Xciting 250

1 Answer

Low voltage at coil on 1983 DR 250


Check for a short, or partially broken wire between CDI and coil. If your wiring is goodbetween there, check between CDI and pick up.

Jul 25, 2009 | 2001 Suzuki DR-Z 250

1 Answer

No spark


There are a # of things that can take your spark out, first I would see if you have power to your ignition coil (100V+). If none there you need to isolate your ignition switch (unplug it or take it out of the equation) and jump your starter solenoid manually or try pushstarting the bike. If still nothing check for voltage going into your CDI box, if none check for voltage out of your stator (over 100V) and your trigger or pulse coil (over 3V). If you find voltage at the stator and not the trigger replace the trigger and vice versa. If there is voltage for both replace CDI box (but be cautious to verify good ground for CDI box and ignition coil). If you find voltage out of your CDI box (over 100V) replace your ignition coil. Good luck!

Apr 11, 2009 | 1992 Suzuki GSX-R 600

1 Answer

Benelli vevet 125 /02 no spark changed coil/lead/plug..?


see if you have ac voltage from the stator coil when cranking motor.if you do,try swiching cdi box out.also check for power to ign. coil.

Feb 11, 2009 | 2008 Benelli Caf? Nero 250

2 Answers

4 wheeler won't start


The Sunl's are notorious for the stator going out. Check with your dealer for specs on testing the stator. It could also be the CDI unit too! I hope this helps

Mar 13, 2008 | Audio Players & Recorders

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

662 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zongshen Experts

Joseph Hoffmann

Level 3 Expert

1755 Answers

Tom Chichester

Level 3 Expert

54195 Answers

Terry
Terry

Level 3 Expert

10337 Answers

Are you a Zongshen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...