HP 5070-2583 & 5070-2584 Remote Control IR Receiver IR Blaser Cable Kit - Answered Questions & Fixed issues


does tv device have a hdmi-1 input
does laptop have a hdmi-1 output port
https://en.wikipedia.org/wiki/HDMI

HP Televison &... | Answered on May 03, 2019 | 24 views


All HP iq77x all-in-one PCs suffer from the same problem of a faulty motherboard. This is primarily a soldering issue on the graphics chip,which develops cracks in the solder balls. The PCs contained a separate graphics card, which goes faulty first. This can be removed and the display connector can be moved on the motherboard to use the on-board graphics. This will eventually show the same issue. A short term fix was to heat the graphics chip with a hot air gun or other means (plenty of suggestions can be found on-line) which sometimes works for a few weeks at most. The only 'permanent' fix is to have the chip professionally removed and re-soldered; an expensive option.
If you are lucky, your PC is still wired to use the add-on graphics card, in which case you might be able to remove this and rewire for the motherboard graphics.

HP Televison &... | Answered on Mar 21, 2019 | 37 views


look on your f buttons f5 on mine

HP Televison &... | Answered on Mar 21, 2019 | 23 views


Sounds like The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
https://electronicshelponline.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.
Search the site by type in the "brand name" to your device; [Exclude the model number], in the "Search box at the top right of the display window of the Homepage" to get gathered related posts. See the site by a desktop. Mobile view has no search box. If you are viewing it by your mobile, see it in webview./

HP Televison &... | Answered on Nov 08, 2018 | 33 views


The first thing to do is go into the device manager and delete the drivers for the display and let windows reinstall them. It may be a bad or out of date driver. So when you restart the computer it will put the driver back. Since you did not post the operating system, there is not a lot more I can tell you. If this does not help, you can try an external monitor to see if the problem is present there. If it is then it may be a display chipset issue.

HP Televison &... | Answered on Jul 15, 2018 | 81 views


What is a grlyb-0311 ??

HP Televison &... | Answered on Feb 08, 2018 | 429 views


you cannot connect them an all in one computer does not support a separate monitor

HP Televison &... | Answered on Jan 26, 2018 | 29 views


If those bars are vertical are going up and down and not horizontal that means the lower circuit board that connect to the plasma panel are bad most likely this is an LG TV but this is not something that can be fixed you can take it apart while at least an hour after it's unplugged before you can touch ID cards along the long circuit board see if there's any connection connection connection that you can disconnect and reconnect and very carefully clean up possibly this could be the problem but usually when you have that type of line which is a vertical line you have a bad panel and that's not good and I'm betting this is an LG TV

HP Televison &... | Answered on Jan 26, 2018 | 26 views


try a laser disc cleaner. https://www.ebay.co.uk/i/162805447175?chn=ps&adgroupid=52097426788&rlsatarget=pla-445083143997&abcId=1058846&adtype=pla&merchantid=115136089&poi=&googleloc=9046354&device=c&campaignid=863276125&crdt=0

HP Televison &... | Answered on Jan 13, 2018 | 356 views


you mean tv turns off ? if so probably power suppy. ebay your model number and you will see board price. youtube model number and there maybe instructional to help you replace diy

HP Televison &... | Answered on Dec 03, 2017 | 24 views


It could be as simple as a fuse

HP Televison &... | Answered on Jul 15, 2017 | 208 views


Maybe there http://h10032.www1.hp.com/ctg/Manual/c04763947

HP Televison &... | Answered on May 30, 2017 | 42 views


If you wish to get some details; visit the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ Faults & possible causes to LCD & Plasma screen are given with illustrations. You can get an idea about the fault to an extent. Faults to all LCD & Plasma screen are similar, irrespective of its brand and screen size.
Search the site by type in the "BRAND NAME" of your device; (Exclude the model number), in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

HP Televison &... | Answered on Jan 26, 2017 | 59 views


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://homenol.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.

HP Televison &... | Answered on Jan 19, 2017 | 43 views


There are many reasons for this fault. If you wish to get more details, visit the site linked here. Screen faults to plasma and LCD TVs are given with illustrations. You will get an idea about the fault to your TV, I'm sure.
http://electronicshelponline.blogspot.com/

HP Televison &... | Answered on Jan 16, 2017 | 34 views


A driver for the monitor may be available, but not likely for Windows 10. Chances are that you have upgraded this machine to Windows 10 and did not get it originally this way. What happens with some of the older systems (and they don't have to more than 2 or 3 years old for this) is that there is no specific video driver found for your onboard (or add-on) video card and Win 10 uses the standard VGA driver. This driver has limited resolution options. You need to investigate and determine what video card you have (nVidia, ATI), and what model the card is. Then go to the appropriate site and download the latest drivers from that site for the card you have. Do not worry if they do not list Windows 10 support. Chances are they will work. Install the updated driver package and see if your resolution issues vanish. To see what driver you currently have, right-click on the Windows Icon in the lower left and select Device Manager. Look under Display Adapter to see what Windows 10 has installed for your machine. If it the Standard VGA (generic), you should try to update it as explained above.

HP Televison &... | Answered on Nov 17, 2016 | 35 views


Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board..

HP Televison &... | Answered on Nov 14, 2016 | 68 views

Not finding what you are looking for?
HP 5070-2583 & 5070-2584 Remote Control IR Receiver IR Blaser Cable Kit Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top HP Televison & Video Experts

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Edward Easley
Edward Easley

Level 2 Expert

97 Answers

Are you a HP Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...