20 Most Recent KitchenAid KSB3 Classic Work Top Blender Questions & Answers


The motor windings have failed. It needs the motor replaced, so it will need to go to a repair center near you. You can find all the information you need from their website.

KitchenAid KSB3... | Answered on Nov 16, 2017


Sounds like its overloaded. Feed it slowly

KitchenAid KSB3... | Answered on Oct 01, 2017


Either the coupling from the motor with the fingers on it is not really attached to the motor shaft or the drive on the blade that engages with it is not attached to the blade shaft. One other thing is that on some models if the rubber jar seal between the beaker and the blade carrier is in the wrong place it can raise the blade drive to not engaging properly with the motor coupling. The gasket goes between the jar and the blade carrier, not under the blade carrier.

KitchenAid KSB3... | Answered on Sep 06, 2015


the top rubber piece could be worn enough that it is not engaging the pitcher. look at it carefully and see if the "teeth" of the rubber disc on top of the base has not cracked and worn away. a picture of the new one can be seen on the parts websites to compare I spent $10.00 for my replacement but i found them at other sites for $6.00. you will need a very skinny 7mm open ended wrench to get the old one off and it is left handed threads that means clockwise will loosen not tighten the part.i ground down my wrench but an ignition wrench from an auto store will usually be thin enough to reach the flats on the shaft under the rubber disc

KitchenAid KSB3... | Answered on Jan 31, 2013


this part is broken. Ineed know the price and shipping and handling 1_19_2013_5_26_53_pm.jpg1_19_2013_5_27_09_pm.jpg1_19_2013_5_27_18_pm.jpg1_19_2013_5_27_39_pm.jpg

KitchenAid KSB3... | Answered on Jan 19, 2013


there is a voltage regulator inside the circuit board , this might have got wet some how . this circuit controls 1-10 speed from a touch of a button . will have to disassemble unit , Auth personal should check this , unless you know electronics

KitchenAid KSB3... | Answered on May 02, 2012


Have you tried the fuse first....

If it is the motor (quite rare), these people may be able to order you one:
http://kitchenaidblenders.co.uk/Home/tabid/36/c/KitchenAid-Blender-Spares/CategoryID/6/Default.aspx

KitchenAid KSB3... | Answered on Sep 03, 2011


It is very easy to fix. You will need a new coupler, which is part number 9704230. There is a set of instructions with video here:http://www.kaparts.co.uk/Howtoremoveablendercoupler/tabid/219/Default.aspx The part is available on Amazon as well as many other sites.

KitchenAid KSB3... | Answered on May 07, 2011


Hi. Our Bobby Blender jar broke and we can't find a replacement. We can part it out; do you still need the blades?

KitchenAid KSB3... | Answered on Nov 07, 2010


This is a common problem. This usually happens when either A) too many ingredients are added to the jar or B) the blade spokes do not sit properly in the coupling (the rubber piece). The coupling can be replaced easily. There is a great video on Applianceinsider.com on how to take the coupling off as recommended by KitchenAid themselves. The part can be found at 1800parts.com if you call them their reps are extremely knowledgeable and will be able to help you find the part in seconds. Or if you have the model number you can locate it right on their site.

KitchenAid KSB3... | Answered on Sep 15, 2010


look on ebay for a replacement second hand unit

KitchenAid KSB3... | Answered on May 14, 2010


Watch this video. If your jar has a lid that screws in rather than pushes in you unfortunately have to purchase a new lid, blade, gasket and collar.

KitchenAid KSB3... | Answered on May 13, 2010


Yes, it is very easy to fix. You will need a new coupler, which is part number 9704230. There is a set of instructions with video here: http://www.kaparts.co.uk/Howtoremoveablendercoupler/tabid/219/Default.aspx

KitchenAid KSB3... | Answered on Feb 13, 2010


Actually the drive gear was vulcanized onto the shaft during the production. If you can get glue to hold it on you're all set but I think you'll end up replacing the whole blender soon. Thank you, Dana

KitchenAid KSB3... | Answered on Oct 18, 2009

Not finding what you are looking for?
KitchenAid KSB3 Classic Work Top Blender Logo

33 questions posted

Ask a Question

Usually answered in minutes!

Top KitchenAid Blenders Experts

Appliance engineer

Level 2 Expert

153 Answers

eyecam

Level 2 Expert

96 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a KitchenAid Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

KitchenAid Blenders

  • KitchenAid Blenders

Most Popular Question

replace glass jug

  • Blenders
Loading...