DISH Network ES190482 Remote 40.0 ES190482 - Page 5 - Answered Questions & Fixed issues


You must take apart the two halves of the remote .
Remove the rubber buttons bad (It usually is one piece)

Get a bottle of 99% iso alcohol at any pharmacy and let the whole rubber pad soak for 2 mins.

While it is soaking, take the end of a rubber pencil, and use it to clean the pc board by rubbing in circles on the printed resistor ink pads individually.

Remove the rubber button pad from the alcohol and dry well.

Take the pencil eraser and rub each individual black resistor ink with it.
Then dip a Q tip in the alcohol and do ALL of the resistor ink on both the pc board and the rubber pad.

Re assemble and there you have it!

Usually when you open the remote and pull the rubber all in one button key pad out, it will be sticky, so clean the button holes on the top piece of the remote (The Insides Individually) or the problem will continue.
The rubber keys will eventually return to rubber and the small black resistor ink on the opposite side will also wear in time.

I have seen this in the shop now for almost 30 years, and it is 95% the same every time!

I hope this will help!

DISH Network... | Answered on Jan 06, 2015 | 58 views


If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/
http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/

DISH Network... | Answered on Dec 29, 2014 | 80 views


557 634 811 626 633 try one of these

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/laura_08254539050d64db

DISH Network... | Answered on Dec 27, 2014 | 49 views


Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician

DISH Network... | Answered on Dec 26, 2014 | 333 views


micromax mm-e73 biss cod

DISH Network... | Answered on Jul 30, 2018 | 601 views


which Dish Receiver do u have. if it is a Dual Tuner (322,625,622, 722) u run a RG6 Coax from the Dish to the back of the Receiver. on back of the receiver there should be two ports (Dish 1,, and Dish2) u will need two short pieces of coax and a Separator ,(which should have come with the Receiver. u hook the coax from the outside Dish to the single port of the Separator , now u run a coax (or RCA or what ever) to the TV. Turn on TV and Receiver.
on the Dish remote u hit the Menu button and hit #6 then #1 and #1 again (wait for each screen to change ) u should see a signal bar at the bottom. U will need to get someone to turn the dish a little at a time till u get a signal. once u get a strong signal u hit the Check Switch and let it program.

DISH Network... | Answered on Nov 12, 2014 | 153 views


Use your TV remote "input" "source" or "tv video" input button. If using the.Dish remote press the clear tv button then input. Repeat to go back to HDMI. Make sure you press sat to change channels once you get back on the HDMI input for dish

DISH Network... | Answered on Oct 28, 2014 | 87 views


Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/
http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/

DISH Network... | Answered on Oct 13, 2014 | 91 views


Take out the batteries immediately. Your remote control need cleaning. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/
You can get details about how to clean a remote control.

DISH Network... | Answered on Oct 09, 2014 | 67 views


You can check out this link for directions on programming your remote: http://www.mydish.com/support/program-non-hopper-to-receiver. Let me know if you have any other questions!

Sarah J.
DISH Social Media Representative

DISH Network... | Answered on Oct 01, 2014 | 119 views


Most likely the cooling fan bearings are going out meaning that you need a new box. Dish should send you one at no charge unless it was a purchased box from a 3 party.

DISH Network... | Answered on Sep 18, 2014 | 151 views


Reset it once again. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience.
http://electro-medical.blogspot.com/
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/

DISH Network... | Answered on Sep 15, 2014 | 169 views


If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience.
http://electro-medical.blogspot.com/
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/

DISH Network... | Answered on Sep 14, 2014 | 242 views


0029,0026.
Try these codes. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience.
http://electro-medical.blogspot.com/
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/

DISH Network... | Answered on Sep 13, 2014 | 567 views


Sounds like a broken power relay.

DISH Network... | Answered on Sep 11, 2014 | 161 views


according to which receiver u have.. some of the dual receivers have the MODE button hidden behind a pop open door on front of the Receiver.. and some have the Mode button under or very near the green and blue light. make sure that BOTH lights are lit.

DISH Network... | Answered on Sep 04, 2014 | 168 views


Channel 1 has always been set aside for emergency freq. (at least that has been true on all TV's in the past..

DISH Network... | Answered on Sep 04, 2014 | 53 views


Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the site linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Pull up older posts.
http://electrohelponline.blogspot.com/
http://remotesearch.blogspot.com/

DISH Network... | Answered on Aug 23, 2014 | 171 views


0281,0288,0280.
Try these codes. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience.
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/

DISH Network... | Answered on Aug 13, 2014 | 26 views


If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience.
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/

DISH Network... | Answered on Aug 09, 2014 | 29 views

Not finding what you are looking for?
DISH Network ES190482 Remote 40.0 ES190482 Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top DISH Network Televison & Video Experts

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Are you a DISH Network Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...