Kenwood KM400 / KM410 Chef Classic Stand Mixer - Answered Questions & Fixed issues


where we can get Blinder spare parts
sheikhmn@gmail.com

Kenwood KM400 /... | Answered on Aug 26, 2018 | 907 views


Hi, the new style tools do not fit old style mixers, yours probably had the small circlip on the shaft, the new ones dont have this, and it's this what held your tool in place

Kenwood KM400 /... | Answered on Jan 11, 2014 | 85 views


Hi, Can you please send me copy of A701A service manual. My email address is bhaymes@engineer.com
Thanks

Kenwood KM400 /... | Answered on Jan 11, 2014 | 630 views


I think you should contact a service rather than opening and cleaning your device for you to be sure that your device will be fixed correctly...

Kenwood KM400 /... | Answered on Aug 30, 2013 | 188 views


I have read on other posts that it is the nut at the top of the beater that is causing the problem. You need to rotate it downwards toward the beater in order to have sufficient room to push and rotate the beater out. This didn't work for me, nor did attempting to remove the whole plate by undoing the lug beside the beater insert. Now that I have worn the lug and the nut I cannot get it repaired at a Kenwood service specialist as I have attempted the repair myself.
My advice is to go straight to a professional. Whatever they charge it will be cheaper than being stuck with a machine you can only use some of the time and have to replace!

Kenwood KM400 /... | Answered on Jul 15, 2013 | 375 views


Hi, this is the drive pinion, have a look on ebay uk

Regards

Kenwood KM400 /... | Answered on Nov 23, 2012 | 217 views


A failed SCR or triac will not always show visually any sign of failure. Chances are good that is all that is wrong. If mixer had been plugged in when it got wet, that is all it takes. Also check the transient voltage supressors if the chef has them. They would be identified on the circuit board. as TVS or MOV along with a number. Only number to use is the one on the component.

If you can find ratings for the old devices, just matching the basic ratings should do. Just guessing, but the SCRs should be 20 amp and 400 volt, If the old ones are a lower rating than my guess, there is no problem with using the higher ratings, if my guess is low, go with the original's ratings. Manufacturer of device does not matter as long as ratings are at least comparable.

Kenwood KM400 /... | Answered on Feb 21, 2012 | 534 views


check the plunge of the kenwood by tracing the connector wire may it remove or if not so then the kenwood has got burnt.

Kenwood KM400 /... | Answered on Nov 05, 2011 | 87 views


I couldn't remove the K-Beater as when I tried to turn it the whole mechanism turned with it. I couldn't even remove the splashguard! I was going to take it to the Kenwood factory (a few miles from home) but then I thought I'd give it one more go and this is what I did...
  1. Next to where the K-Beater attaches in the middle of the circular plate is a lug with a pointed-shape bolt on the end. Remove this with a spanner and the beater plus gear cog can be removed.
  2. Place some mole grips or wide pliers on a worktop and sit the cogged gear in to it and grip so that it won't turn.
  3. Now you should be able to remove the K-Beater!
Perhaps someone can suggest how to stop it happening again. I haven't attached anything since but will update this post if I have any other helpful tips.

Kenwood KM400 /... | Answered on May 30, 2019 | 9,085 views


UK Kenwood / De'Longhi Authorised Repairer Locator:

http://www.kenwoodservice.co.uk/agents/agent-locator2.htm

Kenwood KM400 /... | Answered on Mar 19, 2011 | 375 views

Not finding what you are looking for?
Kenwood KM400 / KM410 Chef Classic Stand Mixer Logo

102 questions posted

Ask a Question

Usually answered in minutes!

Top Kenwood Food Mixers Experts

Peter GW Fleming

Level 1 Expert

3 Answers

Treefrog15
Treefrog15

Level 2 Expert

130 Answers

Yitz Diss

Level 1 Expert

9 Answers

Are you a Kenwood Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...