20 Most Recent GE (PSS26MSRSS) Side by Side Refrigerator - Page 6 Questions & Answers


did you replace the entire control board?

GE (PSS26MSRSS)... | Answered on Aug 17, 2014


Have you checked the light switch. It is common for the light switch to also keep the icemaker from driving the ice through the door. It shouldn't keep the icemaker from making ice though. It could be the icemaker being bad or the water valve being bad.

GE (PSS26MSRSS)... | Answered on Aug 17, 2014


your drain line may be plug up therefore is going above the level make sure you see water on the bottom tray next to the condensing coil under the refrigerator.
thanks.

GE (PSS26MSRSS)... | Answered on Aug 12, 2014


It has a pan but with most GEs the pan as part of the frame and are not removable.

GE (PSS26MSRSS)... | Answered on Aug 02, 2014


The inlet line is either kinked or the line is frozen up which would require a total defrost e.g turn it off for a day. the other reason could be the water valve itself.

GE (PSS26MSRSS)... | Answered on Jul 27, 2014


probably a dish rattling against something else when door closed

GE (PSS26MSRSS)... | Answered on Jul 26, 2014


It circulates cold air throughout the freezer, so everything's about the same temperature. Without the fan, the bottom of the freezer would be colder & the top would be warmer.

It's also important for the automatic defrost timer - it makes defrosting last MUCH less time.

GE (PSS26MSRSS)... | Answered on Jul 26, 2014


The water valve solenoid of the refrigerator has gone bad.

GE (PSS26MSRSS)... | Answered on Jul 14, 2014


If the freezer is cold enough to freeze food hard, look for a problem in the water line, water inlet solenoid valve, or possible ice build up on the ice maker itself that does not the allow the ice maker to complete it eject cycle and start a new ice making cycle.

GE (PSS26MSRSS)... | Answered on Jul 14, 2014


Possible blockage in the water line at the water inlet valve. Possible blockage in the line tapping valve on the cold water line. Possible bad solenoid coil located on top of the water inlet valve.

GE (PSS26MSRSS)... | Answered on Jul 14, 2014


CHECK THIS LINK
http://www.partselect.com/Models/GSS22JFMCWW/

GE (PSS26MSRSS)... | Answered on Jul 14, 2014


Seal around the door should be "warm" not "hot" in my opinion... Only purpose for the electric heat in door seal is to evaporate moisture that will condense on the otherwise cold surface of the door seal causing drippage or if door seal on freezer to prevent frost buildup. In design of unit no reason that engineers would want or need to have this seal 'hot" because a mild temperature say 50 F would be adequate to do the job. Perhaps some physical damage to the electric wire in this circuit causing a short and more current to flow making it heat up???


Maybe not a baffle problem at all...... To me the baffle is such a simple device it would be hard to imagine how it would get screwed up. The one on my old Norge is almost 50 years old.... [ Yeah, I know, I waste probably twice the KWH that you guys do.... but my wife insists on keeping this old coppertone fridge and I keep rep[airing it over the years.]

GE (PSS26MSRSS)... | Answered on Jul 11, 2014


I assume water dispenser works. One possible solution: the plug under the plastic cover has come out of the socket. Remove the plastic cover next to the ice cube maker and reseat the plug.

GE (PSS26MSRSS)... | Answered on Jul 10, 2014


I had a different problem recently on a different model GE refrigerator. My Fridge was up to about 45-50F. Check in the freezer. Is there frost on the back panel inside the freezer? Mine had about a half inch of frost on it. It\'s an indication that the defrost cycle is not working which was due to a temperature sensor on the evaporator that had gone bad. It\'s an inexpensive part that is easy to replace. Most GE\'s use part #AP3185407 (WR55X10025). It was around $9 plus shipping from appliancepartspros.com. First, unload the fridge and freezer and defrost it. Remove the back inside panel of the freezer and the evaporator will probably be caked with frost. Use a hair dryer to remove the rest of the frost. You\'ll see a small white bulb with a double white wire coming off it clipped to the top of the evaporator. Cut the wires and remove the old sensor. Attach the wires of the new sensor to the wires you cut from the old sensor (either solder or use a crimp but connector or similar). Put it all back together and you are in business. I hope this helps.

GE (PSS26MSRSS)... | Answered on Jul 09, 2014

Not finding what you are looking for?
GE (PSS26MSRSS) Side by Side Refrigerator Logo

3,776 questions posted

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

Brad Goodale

Level 2 Expert

106 Answers

Matt Sicignano

Level 1 Expert

7 Answers

JP Meneide
JP Meneide

Level 3 Expert

483 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Refrigerators

  • GE Refrigerators

Most Popular Question

freezer sound like cessna when fan goes

  • Refrigerators
Loading...