20 Most Recent Husqvarna Rose Questions & Answers


The Rose has a sensor on the presser bar assembly that is giving you the grief. The machine thinkss the presser foot is in the raised position.There is a small metal flat spring that has gone bad and causing the error. Find an autorized service center to repair the problem.

Husqvarna Rose | Answered on Mar 07, 2019


Hello

The machine is indicating that it "wants" you to move the hoop into position P2 or P3 according to what is blinking. This is normal.

Once that colour is completed stitching, the machine will communicate again for the nest Position.

Happy Stitching
Sewingirl/

Husqvarna Rose | Answered on Mar 20, 2017


I am sorry to inform you that Husqvarna # 1 embroidery unit does not fit onto the Rose machine. The terminals on the Rose is upright, while on the H # 1 it is flat. If you want to do embroidery on the Rose, you will have to purchase the embroidery unit.

Sad but true

Husqvarna Rose | Answered on Mar 16, 2017


You must slide the feed dog up/down switch over (consult your manual).

If you slide the switch over, the feed dogs will not come up. It is only when the machine makes a full rotation that the mechanism engages and the feed dogs return to the sewing position.

If the feed dogs will still not raise, then you will need to take it to your dealer.

Husqvarna Rose | Answered on Feb 04, 2017


try this and see if it will work for you
When you set the switch for the feed dogs in the up position
turn the handwheel 1 complete revolution and see if
they come up

Husqvarna Rose | Answered on Jul 08, 2016


What Viking is it ? Have you cleaned between the feeders? If all is clean, try this test. Remove needle. Turn hand wheel so that feeders are up. Put fabric in machine. Lower presser foot. Make sure presser foot pressure is set at normal. Try pulling the fabric towards the front of the machine. It should be hard to pull. If it is easy to pull you need new feeders. They are worn down.

Husqvarna Rose | Answered on May 03, 2015


It thinks the presser foot is in the up position. Will need to be repaired by experienced service tech (preferably a certified Viking service tech). There is a clamp that may just be out of place or it could be more involved. Good luck.

Husqvarna Rose | Answered on Apr 03, 2015


you probably need to have an authorized Viking repair person check your machine.

Husqvarna Rose | Answered on Feb 09, 2015


When the bobbin is wound with too much tension it crushes the inside and won't come off the spindle. You need to pull all the thread off the bobbin and replace it. Make sure you wind the bobbin at slow speed and the presser foot is up if you wind through the needle.

Husqvarna Rose | Answered on Oct 30, 2014


The flashing E means the design is either too big for the sewing field limit (about 3.93 x 3.93") or not centered. From the sound of your description, most likely the design is not centered. Check the design size in software and center it before transferring to the card.

Husqvarna Rose | Answered on Sep 10, 2014


Take a small screw driver and slide it under the bobbin and apply a little pressure and it should pop off.

Husqvarna Rose | Answered on Jul 13, 2014


You might try eBay.

Husqvarna Rose | Answered on Jul 13, 2014


Try this link for free manual for the Viking Rose machine -

http://new.husqvarnaviking.com/SiteMedia/Products/Machines/Support/Rose_605_manual_EN.pdf

There are 2 models called 'Rose'. The original Rose is the manual above. The newer Rose is called the Eden Rose. You can find most user manuals for Viking machines on their website. Here's how:

website: http://www.husqvarnaviking.com/us
Go to bottom of page on righthand side and click on 'Machine Updates'.
If your machine is not listed click on 'All Machines"
Scroll down until you find your machine and click on the name of your machine.
The link should take you to a page with a picture of your machine and a link to Download the manual which is a PDF file.

Good luck.

Husqvarna Rose | Answered on Jul 13, 2014


Your user manual should explain how in detail with pictures. It is sometimes hard to get the bulb out without breaking it. But try this -
With machine unplugged/power off lay machine on it's back. Locate the light bulb. You probably have a little rubber device in your accessory case that has a suction cup on each end. One end will say In and the other will say Out. Use the suction cup to grab the bulb and pull straight out. Use the other end to install the new bulb in the machine.

If you need a manual - Try this link for free manual for the Viking Rose machine -

http://new.husqvarnaviking.com/SiteMedia/Products/Machines/Support/Rose_605_manual_EN.pdf

There are 2 models called 'Rose'. The original Rose is the manual above. The newer Rose is called the Eden Rose. You can find most user manuals for Viking machines on their website. Here's how:

website: http://www.husqvarnaviking.com/us
Go to bottom of page on righthand side and click on 'Machine Updates'.
If your machine is not listed click on 'All Machines"
Scroll down until you find your machine and click on the name of your machine.
The link should take you to a page with a picture of your machine and a link to Download the manual which is a PDF file.

Good luck.

Husqvarna Rose | Answered on Jul 13, 2014


try these sites
sew usa
sewing manuals.com
ebay

Husqvarna Rose | Answered on Jul 13, 2014


Try this link for free manual for the Viking Rose machine -

http://new.husqvarnaviking.com/SiteMedia/Products/Machines/Support/Rose_605_manual_EN.pdf

There are 2 models called 'Rose'. The original Rose is the manual above. The newer Rose is called the Eden Rose. You can find most user manuals for Viking machines on their website. Here's how:

website: http://www.husqvarnaviking.com/us
Go to bottom of page on righthand side and click on 'Machine Updates'.
If your machine is not listed click on 'All Machines"
Scroll down until you find your machine and click on the name of your machine.
The link should take you to a page with a picture of your machine and a link to Download the manual which is a PDF file.

Good luck.

Husqvarna Rose | Answered on Jul 13, 2014


Your local Husqvarna Viking dealer can order one for you.

Husqvarna Rose | Answered on May 15, 2014


Are you sure the floppies are corrupt? I suggest you locate a computer professional that sells used computers and tell them what you want done. I'll bet they can transfer the files to a new hard drive for your old computer or to another computer. Be aware that the older embroiderary software is not compatable with Windows Vista, 7, or 8 so don't plan on getting a new computer as part of this update.

Husqvarna Rose | Answered on Apr 15, 2014

Not finding what you are looking for?
Sewing Machines Logo

187 questions posted

Ask a Question

Usually answered in minutes!

Top Husqvarna Sewing Machines Experts

radcal

Level 2 Expert

196 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

220 Answers

Tally Girl
Tally Girl

Level 3 Expert

1134 Answers

Are you a Husqvarna Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Husqvarna Sewing Machines

  • Husqvarna Sewing Machines

Most Popular Question

viking rose sewing machine starts stops

  • Sewing Machines
Loading...