20 Most Recent Champion International Champion Power Equipment 46515 3500 Watt 196cc OHV 4cycle Gas Powered Rv - Page 9 Questions & Answers


Likely you did not tighten it adequately. Use the wrench supplied to free up a stuck disposal, usually a dog leg 1/4" allen wrench. Insert it in the ring and tighten until it locks.

Electrical... | Answered on May 04, 2019


Can you check output for frequency with a meter? It tells me your frequency is high and needs to be adjusted alittle lower by adjusting the speed. The throttle needs to be adjusted! Can you find it? By the carb. The linkage adjusted alittle longer for less fuel to the engine. Good luck!

Electrical... | Answered on May 03, 2019


Sounds like a valve may be sticking open.

Electrical... | Answered on May 02, 2019


Low oil pressure is one of the common faults of generator. The method of quick troubleshooting is helpful to solve the problem in time.BelowJiangsu Starlight Electricity Equipment Co.,Ltd willteach you how to accurately find the cause of generator engine oil pressure problem.


https://www.dieselgeneratortech.com/generators/Cause-and-Solutions-for-Low-Generator-Oil-Pressure.html

Electrical... | Answered on Apr 25, 2019


Your governor is adjusted for the correct 60 hertz cycles. You may have lost residual voltage to excite the generator to produce ac. Being that it was sitting long time.
I could explain in lengthy conversations but you could just google : how to excite a generator and there is good write ups online as well if not better than what I could explain in detail.

Electrical... | Answered on Apr 25, 2019


Try disconnecting the battery for about ten minutes and reattaching positive cable and see if that resets it.

Electrical... | Answered on Apr 25, 2019


Make and Model where this brush and magnet resides?

Click COMMENT under my post.

Electrical... | Answered on Apr 23, 2019


There maybe a centrifugal switch that is stuck on the end cover of the Gen I think. Hope this helps.

Electrical... | Answered on Apr 23, 2019


Then most likely GenSet breaker trip is due to a ground fault. Isolate the fault as follows.

Open all breakers in the Winnie. Start generator without the power cable from the Winnie connected. Connect power cable from Winnie and wait a few seconds. If no trip, turn on main (disconnect) breaker in Winnie. Wait a few seconds, if no trip then proceed to turn on each circuit one at a time.

Comment here with results.

Electrical... | Answered on Apr 23, 2019


Champion RCJ8 (840) Copper Plus Small Engine Spark Plug, you can look online for socket size, usually 5/8 inch older ones are13/16

Electrical... | Answered on Apr 22, 2019


Browser search the term "drill fix generator" and follow instructions on how to use a regular electric drill to correct residual magnetism of a generator.

Electrical... | Answered on Apr 21, 2019


That model number is actually supported by Briggs & Stratton. The phone number to contact them for support is 1-800-274-4477.

Electrical... | Answered on Apr 21, 2019


Since you indicate that two remotes do not work, I am guessing the receiver on the opener is the problem. Verify that connections to the terminals (located where the wires from your hardline buttons are connected) are intact.

Electrical... | Answered on Apr 18, 2019

Not finding what you are looking for?
Champion International Champion Power Equipment 46515 3500 Watt 196cc OHV 4cycle Gas Powered Rv Logo

26 questions posted

Ask a Question

Usually answered in minutes!

Top Champion International Electrical Supplies Experts

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Gene Haynes

Level 3 Expert

5353 Answers

Brad Brown

Level 3 Expert

18072 Answers

Are you a Champion International Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Champion International Electrical Supplies

  • Champion International Electrical Supplies

Most Popular Question

only runs choke

  • Electrical Supplies
Loading...