20 Most Recent Mitsubishi WD-52525 52" Rear Projection HDTV - Page 5 Questions & Answers


the lamp eng it bad you need to replace the dmd or the hole thing the eng, whear the lamp in stall at and i done a lot of them to and that cost a lot 1000.00 plus the core you need to send back to mitsubishi you may whant to call them to see if it under wearenty if not that will till you how much it cost to have it replace..it a big job it chang them to about 2hours to replace them the lamp eng ..good luck i hope this help you out...me my self don,t like a dlp at all the lamp cost to much to replace for lasting just a year. lamp should last about 2 years but i not seen a lamp last that long at all..the samsung is just as bad... will good luck

Mitsubishi... | Answered on Nov 25, 2013


I had another problem kinda the same and emailed ctechnicians.com and they gave the fix.

Mitsubishi... | Answered on Nov 25, 2013


IT IS VERY EXPENSIVE. AND THE TV HAS MANY YEARS?/

Mitsubishi... | Answered on Nov 17, 2013


SOUNDS LIKE CONVERGENCE PROBLEM, COMMON ON PROJECTION TV'S. MAYBE $300 REPAIR. FIND HONEST TV TECH

Mitsubishi... | Answered on Nov 17, 2013


try pressing the small reset button on the TV the light should blink rapidly for about a minute and then stop if it does not stop you will need to have the TV repaired

Mitsubishi... | Answered on Nov 04, 2013


am sure the lamp is fine. first thing replace the lamp thermal sensor if this does not work check the lamp ballast (aka) lamp power supply.

Mitsubishi... | Answered on Oct 09, 2013


The WS is a picture tube type rear projection first produced as a 2003 model year set.

A few questions and then a offer if needed.

Did this happen suddenly or after a power loss?

By reboot do you mean the recessed reset button on the front of the set?

I will presume if you turn color off completely the screen is some other color than black and white?

the offer: have you tried the Option menu this set has hidden, I can explain if needed.

Mitsubishi... | Answered on Sep 02, 2013


replace the converge ic's

Mitsubishi... | Answered on Aug 17, 2013


try to reset press menu 123 enter if not sounds like a engine big bucks.

Mitsubishi... | Answered on Aug 02, 2013


you must test the power supply inside. See if the fan is working, and thermostat is ok. test it.
God bless you

Mitsubishi... | Answered on Aug 01, 2013


I have the exact same problem.
TV was working fine (if you call having to deal with blinking lights of death and multiple starrt up errors...) - but I powered through it all.
This TV is 6 years old and started acting up after the 4-year extended warranty ran out.
This morning I went to turn it on and nothing.
Hmmm... Got my manual to count the blinking light code...
Whoops. No lights. Nothing. Checked plug. Checked power.
Uninstalled and installed lamp. Checked plug and power again.
Nothing.
Not one stinking light. No power to fan. Nothing.

How does a TV just DIE???

Mitsubishi... | Answered on Jul 24, 2013


If you wish to get more details, check this site linked below. Pull up older posts there. Check the site with patience, as it has over 2400 posts now. All are related to electronic equipment repair help. If you search the site in Timeslide option, which can be selected from the drop down list at the top left of the display window, it will be easy to locate the related post. You can also do a search by type in the brand name to your device into its search box at the top right of display window. Your problem post haven't enough details to provide a solution.http://electronicshelponline.blogspot.com/

Mitsubishi... | Answered on May 02, 2013


there's a blue switch that needs to be actuated when you put the 2 lamp covers on.

Mitsubishi... | Answered on Apr 20, 2013


You're asking the way to access the ballast board, I assumes and posts this solution. You have to disassemble the set. If you wish to get more details, check this site. Pull up older posts there. Check the site with patience, as it has over 2250 posts now. All are related to electronic equipment repair help. Search the site by 'Timeslide' option. It will make search easy. Or, type in the brand name to your device into its search box, and press "Enter" Disassembley procedure is given in detail with illustrations. I can't include all that illustrations and descriptions here by this window.

Mitsubishi... | Answered on Apr 11, 2013


The lamp cover is not installed properly or the lamp door switch isnt working thats what causes the 32 error.

Mitsubishi... | Answered on Apr 08, 2013

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

1,606 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76100 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WD Mitsubishi

  • WD Mitsubishi

Most Popular Question

bulb goes out after few minutes

  • Televison & Video
Loading...